1. AUMA Electric Actuators

2. AUMA scope of supply
Actuators for valves requiring multi turn actuation:
Gate valves
Sluice gates
Globe valves
Pinch valves
Actuators for valves requiring quarter turn actuation:
Butterfly valves
Ball valves
Plug valves
Actuators for valves requiring linear actuation:
AUMA offers actuators for all types of valves. 2

3. AUMA provides a complete range of electric actuators
Multi turn output up to 60,000 ft lb torque / 900,000 lb thrust
Quarter turn output up to 498,000 ft lb torque
Linear output up to 48,825 lb thrust
Actuators are available for small and larger valves.

4. AUMA offers three actuator control configurations
Conventional actuator
Limit switches
Torque switches
Without controls – AUMA NORM
Conventional actuator
Limit switches
Torque switches
Conventional controls
AUMA Matic (AM)
Plant owners and operators in various industries have a wide variety of requirements of actuators. AUMA has a solution for virtually all of those requirements.
The AUMA offering covers all types of actuator configurations including actuators without integral controls, with conventional controls and with microprocessor-based controls.
Non-intrusive actuator
MWG – encoders sense position & torque
Microprocessor- based controls
AUMATIC (AC)

5. A solution for any environmental / ambient application
Watertight applications
NEMA 4 / 4X
IP67
Explosionproof applications FM
CSA
ATEX
Other global approvals
High & low ambient temperature
As high as +250º F (+120º C)
As low as -76º F (-60º C)
Submersible applications
NEMA 6
IP68
Automated valves are located in all types of locations and ambient conditions. AUMA has a solution for most of those requirements.

6. Model SA multiturn actuator
Drive - motor (or hand wheel) drives a worm/worm wheel gearset which turns a hollow output drive shaft.
The SA is AUMA’s primary product line. A motor drives a worm shaft that in-turn drives a worm wheel, then the actuator output shaft. A handwheel drives the opposite side of the worm shaft in case manual operation is required. The actuator incorporates modular design. An example is how the motor can be easily removed by loosening 4 bolts and disconnecting a plug & socket connection at the motor – all without requiring access to the grease-filled gearcase. As with all AUMA electric actuators, it’s watertight with O-ring seals to meet the enclosure standard IP67 or NEMA 4X/6 – suitable for submersion in 6 ft of water for 30 minutes.

7. Model SA multiturn actuator
11 sizes
output torque from 7 to 23,600 ft lbs
thrust acceptance up to 450,000 lbs
speed from 4.8 up to 216 rpm (at 60 Hz, in 12 increments - speed selections reduced for larger actuators)
This wide range of sizes and output speeds enables the SA actuator to serve many valve automation applications. Versions are available for modulating service (SAR), high ambient temperature (SAH) low ambient temperature (SAT) and enhanced submersion protection (IP68). The SAExC is available for environments where hazardous gases or dust are present.
SA07.2 – SA16.2
SA25.1 – SA48.1

8. SA Multiturn Actuator coupled with GK or GHT Multiturn Gearbox
SA actuator / GK gearbox
Up to 11,900 ft lb torque
Up to 309,000 lb thrust
An SA multiturn actuator coupled with a GK bevel gearbox or GHT gearbox can be used in applications where high torque is required or high thrust must be accepted. Usually. The actuator / gearbox combination is more cost-effective than a larger direct mount actuator.
Multiturn actuator/gearbox combinations can be provided with thrust capability of up to 900,000 pounds.
SA actuator / GHT gearbox
Up to 60,000 ft lb torque
Up to 900,000 lb thrust

9. Plug & socket electrical connection
Screw / compression connection (no special tools required)
Field wiring can be performed prior to actuator / valve installation
Once wired, field wiring can be unplugged
Can be utilized as a disconnect or supplied with a disconnect switch
Safe terminals
Optional ring-tongue terminals
The plug and socket electrical connection is a big favorite of plant owners and valve assemblers.

10. Easily to set-up / commission
Easily settable position limit switches
Just a few turns of a slotted shaft
No declutch shaft
Easy torque switch adjustment
Test knobs to check limit & torque switches
AUMA’s switch setting procedure is the simplest in the industry. 10

11. User friendly design offers actuator configuration flexibility
SA actuators can be furnished as conventional or non-intrusive actuators
The tried and proven SA range of actuators can be supplied as either a conventional or non-intrusive actuator.

12. SA actuators can be furnished as ‘non-intrusive’ actuators
What is a non-intrusive actuator?
An actuator whose parameters can be set without gaining access to the inside of the unit.
Non-Intrusive
Non-intrusive actuators are preferred by some end users, particularly in industries where hazardous gases or dust are present. In non-intrusive actuators, position and torque are mechanically sensed as in conventional actuators, but instead of switches, encoders are used. AUMA uses reliable absolute encoders that do not require a battery to store current valve position data or record actuator travel when normal power is not available. The encoders work with a microprocessor to control the position and torque limit functions. The encoder / microprocessor also provide plant operating personnel with a broad range of information on the automated valve. The microprocessor is provided with the AUMATIC actuator control package which must be included when a non-intrusive actuator is furnished.

13. Non-intrusive actuators - 3 ways to set parameters
Manipulate local controls
Wirelessly via laptop
Wirelessly via Windows-based PDA

14. SA or SA/GK Multiturn actuator - Output Drives for many applicationsLE B AF A
A wide variety of output drives allow the SA multiturn actuator to operate many valve types.
Also available:
D / DD / B3D
IB3 AK 14 14

15. SG05.1 – 12.1 Quarterturn Actuator
4 sizes (SG SG12.1)
up to 880 ft lbs output torque
capable of ‘open/close’ service and ‘positioning’ or ‘modulating’ service up to starts per hour
variable operating time (single phase)
separate splined coupling
plug & socket electrical connection
double seal available
non-intrusive version available
version available for hazardous locations according to FM, ATEX or CSA standards
AUMA’s SG.1 series of quarterturn actuators is available in 4 sizes with output torque up to 880 ft lb.

16. SG.1 Quarterturn Actuator
Motor drives a three-stage planetary gear set which drives a worm/worm wheel gear set and finally a splined coupling. Hand wheel drives planetary gear housing then worm and coupling.
The motor drives a 3-stage planetary gear which in-turn drives a worm/worm wheel gear set. A handwheel is available for manual operation. A separate splined coupling transmits torque from the actuator to the valve stem. The SG.1 series can also be furnished in a non-intrusive version.

17. AUMA GS worm gearbox models
12 sizes
GS50.3 – GS250.3
GS315 – GS500
GS630.3
Output torque up to 498,000 ft lbs
Wide variety of primary spur gear reducers
VZ on GS100.3 – GS125.3
GZ on GS160.3 – GS630.3
GS 50.3 – 125.3
GS – 250.3
AUMA offers a wide range of worm gearboxes primarily for part-turn or quarterturn applications.
GS 315 – 500
GS630.3

18. Model GS worm gear - Applications
Manual operator
Meets AWWA Standard C for manual butterfly valves (when properly selected)
Electric actuator for quarter turn applications
Electric actuator for guillotine damper applications
Electric actuator for diverter damper applications
Electric actuator for tainter gates
The GS is suitable for manual operation according to AWWA C With the standard 360 degree worm wheel, it is also a good fit for applications requiring more than one output revolution – such as a guillotine damper or tainter gate.

19. SA/GS Quarterturn Actuator
Multiturn actuator (model SA) directly coupled
worm gearbox (model GS)
worm gearbox / primary reducer combination (model GS/GZ)
Up to 498,000 ft lbs output torque for quarter turn applications
Combined features of SA actuator and GS worm gearbox
The wide range of primary gear reducers makes the GS the perfect gearbox for electric operation when furnished with an SA multiturn actuator.

20. AM integral actuator controls
Used as the motor controls with SA, SAR and SG actuators.
Every motor must be controlled. AUMA offers two motor/actuator control packages. The actuators shown on this slide have AUMA Matic controls.

21. AM integral actuator controls
Standard features:
reversing starters
plug & socket electrical connection – at field terminals and NORM actuator
power supply / transformer
phase correction
monitor relay
local controls
standard interface (contact closure/discrete inputs)
Options:
optional control system interfaces
Positioner – accepts 4-20 mA signal
Pulse timer board – extends operating time
Digital communications boards
solid state starters
The AUMA Matic includes reversing starters, phase correction, monitor relay, local controls, plug & socket at the field terminals and NORM actuator in addition to a control system interface capable of accepting discrete open and close signals. Optional interfaces include an analog positioner.

22. AM integral actuator control package
Local controls:
3 pushbuttons (OPEN – STOP – CLOSE)
3 indicating lights (OPEN – FAULT – CLOSED)
Selector switch (LOCAL – STOP – REMOTE)

23. AM with fieldbus
The Matic is also available with PROFIBUS & Modbus digital communication interfaces.

24. AM Triple Play with fieldbus
Standard features:
Reversing starters for motor control
Plug & socket electrical connection at field terminals and at NORM actuator
power supply / transformer
phase discriminator
local controls
Option:
solid state starters
DeviceNet
The Triple Play Matic is capable of interfacing with DeviceNet and Modbus.

25. AC01.2 integral actuator controls
Required for non-intrusive SA, SAR and SG.1 actuators
Can also be used as the motor controls for conventional SA, SAR & SG actuators.
The AUMATIC is AUMA’s microprocessor-based control package. The actuators shown on this slide have AUMATICs.

26. AC01.2 actuator controls Standard features: Options
Reversing starters for motor control
Plug & socket electrical connection at field terminals and at NORM actuator
Power supply / transformer for control power
Phase correction
Monitor relay
Programmable output relays (45 parameters available)
standard interface (contact closure / discrete inputs)
Local controls with LCD display
Diagnostics
Operational data logging
Electronic nameplate
Configurable via local controls or Bluetooth
Options
Adaptive positioner
Solid state starters
Digital communications / fieldbus / two-wire control
The AUMATIC offers the features found in the Matic with the addition of a 4-line LCD display in plain text, programmable relays and programmable local indicating lights.

27. AC01.2 - local controls Push-buttons: OPEN-STOP-CLOSE, RESET
5 indicating lights – programmable with 45 parameters available, for example:
End position CLOSED
End position OPEN
Fault
Selector switch in REMOTE
Actuator moving
Selector switch: LOCAL-OFF-REMOTE
Display on LCD
Valve position indication
Running indication
Setting menu
Status indication
Diagnostic information
Programmable lights mean we can program the lights to indicate a wide range of actuator outputs.

28. AC01.2 with fieldbus
The AUMATIC is also capable of communicating via one of four digital communication protocols.

29. Commissioning / programming
From laptop or PDA via Bluetooth® interface
Connects actuator to AUMA PC software ToolSuite – Commissioning & Diagnostic Tool

30. Additional user- friendly features

31. Double-seal at terminal compartment
Available on all AUMA actuators
The SA multiturn actuator is an automation solution that can be used in many applications.
Seals terminal compartment from balance of actuator enclosure

32. AM and AC.....flexible mounting
AM and AC can be rotated on the NORM actuator.
Terminal compartment can be rotated on the actuator.
Local controls can be rotated on the AM or AC.
An AUMA exclusive feature!

33. Remote Mounting
Both the AM and AC can be remote mounted using an available wall bracket.
Remote mounting is a good idea when vibration or environmental conditions prevent the use of integral controls at the actuator.

34. A solution for any valve automation application
Spur gearboxes
Pedesatal mounted linear thrust units
Pedestal mounted/lever output actuators 34

35. Electric actuators for all applications
AUMA Actuators
Electric actuators for all applications
Actuators for all valve types and sizes and a wide range of control system interfaces make AUMA the logical choice for valve automation applications.