1. Thermal Mapping Drone Jamyang Tenzin, Dylan Fallon, Stefan Totino, Jason Fellows Faculty Advisor: Prof. Joseph Bardin Department of Electrical and Computer Engineering ECE 415/ECE 416 – SENIOR DESIGN PROJECT 2015 College of Engineering - University of Massachusetts Amherst SDP15 System Process and Overview Results Acknowledgements Abstract Our system is a remote controlled drone capable of detecting significant temperature difference, with respect to the average temperature of an area below its flight path. Our intention is for homeowners to use the device as tool to scan their rooftop and identify areas of poor insulation. Utilizing emerging drone technology is a safer alternative to the current hand held instruments used for this type of application. Data from an IR- sensor complemented with a JPEG camera creates an intuitive map users can analyze. System Block Diagram QuadCopter: APM 2.6 with barometer, gyroscope, GPS & accelerometer sensor for flight Control with Lipo Batteries, electronic speed controller (ESC) and motors IR & Visible Light Cameras: MLX90620 IR Sensor, Adafruit TTL Serial JPEG camera UltraSonic Sensor for height measurement Radio Link: Nordic NRF24L0 Transceiver 3D printed Cover from M5 User Interface: Java/JavaScript/HTML Web Application Specifications SpecificationGoalActual Weight< 2000g1360g Flight time10 min5 min Power Consumption< 250 W239.5 W Cost< $500$1,100 Max flight altitude20 ft50 ft IR-sensor Temperature range-50C to 300C IR field of view (FOV)60° Radio link range>100 ft300 ft Pilot navigates to scan the roof If temperature difference of 5˚C with respect to average is found, LED light Signals pilot to stop Infrared and distance readings are transmitted from drone to receiver JPEG picture is taken and transmitted Data is received and displayed LED light shuts off signaling pilot to continue scanning We would like to thank Prof. Joseph Bardin for advising us on this project. Special thanks to Prof. Christopher Hollot, Prof. Christopher Salthouse & Fran Caron for your guidance. Successful flight with full load Temperature difference detection algorithm Transmission of IR data and 12KB JPEG over radio link USB driver on receiving end feeds incoming data to Java application Data processed and displayed via a web browser Jamyang Tenzin, EE Stefan Totino, CSE Prof. Joseph Bardin Jason Fellows, EE Dylan Fallon, EE

2. Cost Drone Radio Link IR Sensor Receiver Application Experiment Arduino Mega Power Module Flight ControllerMotor Unit IR- Sensor Unit RxTx Radio Controller Power Distribution signal Flight Controller APM 2.6 takes input signals from Radio Controller and Outputs required signals to Electronic Speed Controller (ESC) to do proper flight manuever Electronic Speed Controller (ESC) converts DC current to AC current depending on the signal coming from APM 2.6 1000KV brushless motor takes AC current from ESC to power itself with maximum total thrust 2480g 1800mAh Lipo Battery is used for powering both motor and flight controller QtyPartDevelopmentProduction 1Drone 330mm Frame$11.25$5.00 41000KV motors$66.60$60.00 4motor accessory$8.36$6.00 1Radio Controller$69.97 4Carbon Fibre Propellors$9.12 11800 mAh Lipo Battery$15.90 1APM 2.6 Flight Controller$159.99 4Electronic Speed Controller$103.96 1IR Sensor$87.60$50.00 1Arduino Uno$13.00 1Arduino Mega$29.00 1Transciever$12.00$4.00 1camera$ 39..99 $39.99 1ultrasonic sensor $10.99 1radio telemetry$23.86$15.00 4Drone legs$8.00$2.00 1Lipo Charger$21.35 1Lipo Charger adaptor$13.00$10.00 1shock absorber$10.00$5.00 Total$713.94$630.27 2 Nordic NRF2401+ transceivers Transmits data 32 byte packets at a time, IR data is permitted to transmit upon specified temperature difference, camera data is transmitted right after Data rate of 1 Mbps @ 2.4GHz Arduino Mega controls transceiver on drone, Arduino uno controls transceiver at receiver application Arduino Uno feeds incoming data into PC’s USB port Processing IDE mini app reads from port and writes data to a text file Text file contains 1 byte which represents drones height above target, 64 bytes which represent temperature readings, and about 12,000 bytes which represent a JPEG image file Java program creates a.jpg file out of the 12,000 image data bytes and sends the other 65 bytes up to the client side program using an HTTP API Client side program uses JavaScript/HTML/CSS to create a colored grid out of the temps, overlay the grid over the.jpg file and display the output in a web browser For our experiment we setup a section of our room to try to detect temperature differences. We laid a grid of the field of view of our IR sensor on a wall. We then put various objects of significant temperature difference’s on the gird and looked to detect them. The IR sensor was then moved further away to check the accuracy from different distances. In conclusion we were able to detect temperature differences with good accuracy, accuracy decreased as we increased the field of view for the IR sensor MLX 90620 contains 64 infrared pixels. Utilizes a Proportional To Absolute Temperature (PTAT) sensor to compare objects in its field of view to the ambient temperature of the chip itself. Outputs 16x4 array of temperature readings 1Hz refresh rate IR and PTAT data stored in internal RAM, accessed by Arduino through I2C interface