1. LoopBuster Hardware Loop Detection in Fast Mesh Ethernet Networks Uriel Peled and Tal Kol Guided by Boaz Mizrahi Advised by Gideon Kaempfer Digital Systems Laboratory Faculty of Electrical Engineering, Technion Winter 2007 – Spring 2009 Completion Presentation

2. Ethernet Drawbacks Tree Topologies For Loop Prevention A B C

3. LoopBuster Stop Loops Without Tree Topology A B C New Hardware Device: “LoopBuster” Improved Switches: Changed Learning Improved Switches: Changed Learning Mesh Topology: Loops Allowed!

4. Design Challenges LoopBuster Device Support very high throughputs Ethernet supports 1Gbps and 10Gbps links Implementation must be in hardware Use limited amount of on-chip memory Naïve implementation requires 10Mbit for a single 10Gbps interface Minimal effect on hosting network Remove looping packets quickly Minimize false positives Rely on existing standards / network equipment

5. packet packet packet packet packet packet packet packet packet packet Filter Conceptual Diagram LoopBuster Device Low memory filters in decreasing size Still effective – packet rate decreases We pay with N+1 mandatory loops

6. Project Milestones   Full Network Software Simulation pre-hardware implementation   Analyze Algorithm Parameters   Design LoopBuster Device macro, micro architectures, Verilog implementation   Board Bring-up board selection, cores, GbE   Testing, Validation and Debug   Demonstrate Working Prototype

7. Algorithm Parameters Performance-Cost Tradeoffs Number of filter chains Parallel chains for different MLTTs Different chains for different traffic types Number of filters in each chain Number of loops before terminating a packet Memory size of each filter in each chain Minimize false positives while saving memory Filter scheduling and control patterns Lock / unlock states, reset filter memory

8. Network Simulation in Software Minimal HW (1PC), C++, SW Timeline Real-world rates, real-world traffic Based on a genetic algorithm Genetic representation: filter size list ( 13,12,10,10,9,9,8,8,7,7,6) Improve a pre-defined fitness function False positives over real traffic + Total memory size Two-stage mutation General (add/remove filter, change filter size, switch filters) Specific (num filters, size of largest, create descending chain) Algorithm Analysis Empirical Param Selection

9. Theoretical algorithm performance analysis Probability model for a filter / filter chain C collisions with X packets through an N-bit filter Occupancy problem, numerical solution in C++ Algorithm Analysis Theoretical Param Selection

10. Modular Filter Chain Design Traffic sensitive Code / Runtime Configurable Parameters UART controlled lock/unlock/reset patterns 2 Clock Domains 125 MHz (GbE), 31 MHz (Processing) Packet Pipeline Processing No store and forward (untraditional MAC) Hardware only (no Power PC) Preliminary Design Decision Algorithm Analysis Conclusions

11. Architecture Board Block Diagram

12. Architecture General Block Diagram

13. Packet Transceiver Block Diagram 125 MHz clock boundary Ethernet data in 8-bit units 31 MHz clock boundary Ethernet data in 32-bit units

14. LoopBuster Filter Block Diagram

15. LoopBuster Filter Implementation Supports two concurrent packet paths Unique clock domain: 125 MHz lb_filter_memory (Memory) Filter BRAM wrapper (2 asynchronous ports) Wide write port for asynchronous reset (FSM) Narrow read/write port for filter memory access Supports lock/unlock states lb_filter_state_machine (Filter Logic) Mutual exclusion for memory access Fine-grained locking (cycle requirement per state)

16. Board Selection Selected Board Memec FF1152 Xilinx Virtex-II Pro Existing in lab ($0) 2 SFP Modules 1Gbps Eth. RJ45 Gidi (~$200) PCS/PMA Core Required for SFP Free from Xilinx ($0)

17. Board Functionally Test Download a full working Ethernet example project to test UART, SFPs, LEDs, FPGA, cable correct operation Working DCM Synthesize a working DCM with 125Mhz, 31.5Mhz clock trees. Output main control signals to LEDs (ticker, locked) Core Linkup Test Configure Xilinx gig_eth_pcs_pma CORE for 1GE functionality with correct parameters, timing constrains and physical locs Output CORE status signals to detect linkup Loopback Tests Perform CORE loopback test, Packet transceiver loopback, full data path loopback GbE Board Bring-Up Vertical Development Stages

18. Behavioral Simulations Pre-synthesis Verilog for logic functionality on ModelSim Post-Route Timing Simulations Post-synthesis Verilog for timing on Xilinx ISE 9.2 Automatic Simulation Test-bench Script-based scenario test-benches for core modules (like pt_rx) Automated ModelSim with debug textual log file ($fdisplay) On-Board Live Debugging Status signals to LED, R/W of debug registers with UART Custom event-based debug code (output to UART) System Integration Testing Stream raw Ethernet traffic through device, Packetyzer sniffer Testing and Validation

19. Planned / Actual Schedule Full Network Software Simulation PLAN: 2 months ACTUAL: 2 months Analyze Algorithm Parameters PLAN: 1 month ACTUAL: 1 month Design LoopBuster Device (micro-macro) PLAN: 3 months ACTUAL: 3 months Board Bring-up PLAN: 1 month ACTUAL: 3 months Testing, Validation and Debug PLAN: 2 months ACTUAL: 4 months Demonstrate Working Prototype PLAN: 1 month ACTUAL: 1 month TOTAL PLAN: 10 months ACTUAL: 14 months

20. Main Project Achievements Algorithm analysis and params based on software simulations Working LoopBuster prototype in hardware (FPGA) Testing and validation environment LoopBuster-PC communication and control platform Further Work LBP switch implementation with revised learning algorithm Complete network solution demonstration in hardware In-depth LoopBuster algorithm analysis and optimization with hardware-based results Achievements and Further Work