Presentation is loading. Please wait.

Presentation is loading. Please wait.

Tutorial: Handlebars Chapter 5. 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION.

Published by Modified over 9 years ago

Similar presentations

Presentation on theme: "Tutorial: Handlebars Chapter 5. 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION."— Presentation transcript:

1 Tutorial: Handlebars Chapter 5

2 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

3 Path Sketch Lines drawn and dimensioned in ZX-plane: INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

4 Path Sketch (cont.) Lines drawn and dimensioned in YZ-plane: INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

5 Path Sketch (cont.) Sketch fillets added: INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

6 Profile Sketch INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

7 Swept Base INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

8 Mirrored Feature INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

Download ppt "Tutorial: Handlebars Chapter 5. 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION."

Similar presentations

3.5 Graphs in Three Dimensions 2.Graphing Equations in Three Dimensions.

3.5 Graphs in Three Dimensions 2.Graphing Equations in Three Dimensions.
YZ XY Z X Y First eighth. YZ XY Z X Y second eighth.

YZ XY Z X Y First eighth. YZ XY Z X Y second eighth.
SolidWorks Week 2-3.

SolidWorks Week 2-3.
Tutorial: Bracket Chapter 3.

Tutorial: Bracket Chapter 3.
Feature-Based Modeling and Optional Advanced Modeling

Feature-Based Modeling and Optional Advanced Modeling
Ken YoussefiPDM I,SJSU 1 Sweep Command – Sweep along a Guide Guide Section Insert → Sweep → Sweep along Guide Or select Sweep along from the toolbar Sweep.

Ken YoussefiPDM I,SJSU 1 Sweep Command – Sweep along a Guide Guide Section Insert → Sweep → Sweep along Guide Or select Sweep along from the toolbar Sweep.
Sean Dalton www.itsligo.ie/staff/sdalton. Features Toolbar Select tool Select tool Sketch tool Sketch tool Material Addition Material Addition Material.

Sean Dalton Features Toolbar Select tool Select tool Sketch tool Sketch tool Material Addition Material Addition Material.
Dr Simin Nasseri, SPSU Tutorial: Pulley Chapter 2 Dr Simin Nasseri, SPSU Copyright of Howard and Musto, 2009.

Dr Simin Nasseri, SPSU Tutorial: Pulley Chapter 2 Dr Simin Nasseri, SPSU Copyright of Howard and Musto, 2009.
STOVE BURNERS YOU CANNOT MAKE A FLAT TOP ELECTRIC STOVE GAS BURNER ON SLIDE 6.

STOVE BURNERS YOU CANNOT MAKE A FLAT TOP ELECTRIC STOVE GAS BURNER ON SLIDE 6.
Geometry Control – Modifying and Relimiting; Using Axes and Transformation Ideas Chapter 2: 2.4 & 2.5 R. Lindeke IE 1225.

Geometry Control – Modifying and Relimiting; Using Axes and Transformation Ideas Chapter 2: 2.4 & 2.5 R. Lindeke IE 1225.
Ken YoussefiIntroduction to Engineering – E10 1 Sweep Creates a solid with uniform cross section Profile Path Loft (sweep and blend combined Creates a.

Ken YoussefiIntroduction to Engineering – E10 1 Sweep Creates a solid with uniform cross section Profile Path Loft (sweep and blend combined Creates a.
Tutorial: Advanced Assemblies

Tutorial: Advanced Assemblies
Tutorial: Business Card Holder

Tutorial: Business Card Holder
SolidWorks Session 2 Ferdowsi University of Mashhad Dr. Behnam Moetakef Imani Winter 2011.

SolidWorks Session 2 Ferdowsi University of Mashhad Dr. Behnam Moetakef Imani Winter 2011.
Tutorial: Hatch Assembly

Tutorial: Hatch Assembly
Tutorial: Drawing with Design Table Chapter 4. Multiple-Configuration Drawings Common for small components such as screws, nuts, O-rings, etc. Allows.

Tutorial: Drawing with Design Table Chapter 4. Multiple-Configuration Drawings Common for small components such as screws, nuts, O-rings, etc. Allows.
Tutorial: Drawings Chapter 2. Choose a Paper Size/Format Leave Unchecked for Plain Sheet INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009.

Tutorial: Drawings Chapter 2. Choose a Paper Size/Format Leave Unchecked for Plain Sheet INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009.
The Hong Kong University of Science and Technology MECH 251 CAD/CAM MECH251 LABORATORY CLASS SolidWorks & MasterCAM learning.

The Hong Kong University of Science and Technology MECH 251 CAD/CAM MECH251 LABORATORY CLASS SolidWorks & MasterCAM learning.
Tutorial: Pulley Chapter 1.

Tutorial: Pulley Chapter 1.
Tutorials: Swept Geometries Chapter 5. Swept Boss/Base Two sketches are required: the path and the profile INTRODUCTION TO SOLID MODELING USING SOLIDWORKS.

Tutorials: Swept Geometries Chapter 5. Swept Boss/Base Two sketches are required: the path and the profile INTRODUCTION TO SOLID MODELING USING SOLIDWORKS.

Similar presentations

Ads by Google