1. SCIPP R&D on Long Shaping- Time Electronics SLAC SiD Workshop October 26-28, 2006 Bruce Schumm

2. Faculty/Senior Vitaliy Fadeyev Alex Grillo Bruce Schumm Abe Seiden Post-Docs Jurgen Kroseberg Students Greg Horn Gabriel Saffier- Ewing The SCIPP/UCSC ILC HARDWARE GROUP Lead Engineer: Ned Spencer Technical Staff: Max Wilder, Forest Martinez-McKinney (Students are undergraduates from physics)

3. Alternative: shorter ladders, but better point resolution The LSTFE approach would be well suited to use in short-strip applications, and would offer several potential advantages relative to other approaches Optimized for LC tracking (less complex) More efficient data flow No need for buffering Would require development of 2000 channel chip w/ bump bonding (should be solved by KPiX development)

4. ~1  s shaping time; analog readout is Time-Over-Thresh Process: TSMC 0.25  m CMOS The LSTFE ASIC

5. 1/4 mip 1 mip 128 mip Operating point threshold Readout threshold

6. Electronics Simulation Detector: 167 cm ladder, 50  m pitch, 50  m readout Analog Measurement: Employs time-over- threshold with 400 ns clock period; lookup table provides conversions back into analog pulse height (as for actual data) RMS Gaussian Fit Detector Resolution (units of 10  m) Essential tool for design of front-end ASIC

7. FIFO (Leading and trailing transitions) Low Comparator Leading-Edge-Enable Domain Proposed LSTFE Back-End Architecture Clock Period  = 400 nsec Event Time 8:1 Multi- plexing (  clock = 50 ns)

8. DIGITAL ARCHITECTURE: FPGA DEVELOPMENT Design permits real-time accumulation and readout of hit information, with dead time limited only by amplifier shaping time

9. FPGA-based control and data- acquisition system INITIAL RESULTS LSTFE-2 chip mounted on readout board

10. Comparator S Curves Vary threshold for given input charge Read out system with FPG-based DAQ Get 1-erf(threshold) with 50% point giving response, and width giving noise Stable behavior to V thresh < 10% of min-i Q in = 0.5 fC Q in = 3.0 fC Q in = 2.5 fC Q in = 2.0 fC Q in = 1.5 fC Q in = 1.0 fC

11. Noise vs. Capacitance (at  shape = 1.2  s) Loaded with Capacitor Measured dependence is (noise in equivalent electrons)  noise = 375 + 8.9*C with C in pF. Connected to Ladder Noise is approximately 30% worse; are currently exploring long shaping-time shielding requirements Observed Expected 1 meter

12. Preamp Response Power Control Shaper Response Power Cycling As designed: Achieve 40 msec turn-on due to protection diode leakage Injecting small (< 1nA) current: Achieve 0.9 msec LSTFE2 will incorporate active feedback to maintain bias levels of isolated circuitry when chip is “off”.

13. LSTFE2 The LSTFE2 is currently under development; submission expected by end of year Retain 1.0-1.5  s shaping time Further S/N optimization (still geared towards long ladders) “Off” state feedback to achieve power cycling goal (< 1 msec switch-on) 64-128 channels, with multiplexing of compar- ator outputs (pad geometry)

14. SCIPP Simulation Studies for the SiD Design SLAC SiD Workshop October 26-28, 2006 Bruce Schumm

15. Personnel: B.S. plus three junior undergrads Lori Stevens (worked over summer) Tyler Rice (work over summer) Chris Meyer (new) We are: continuing the study of the use of Tim Nelson’s AxialBarrelTracker as a clean-up algorithm (Lori, Tyler) trying to implement and verify new tracking algorithms (which ones?) - Chris

16. AxialBarrelTracker Studies Still “cheating”: eliminating all hits from the 95% of tracks that originate within 2cm of origin Trying to do full classification of remaining hits (non-prompt tracks, loopers, backgrounds, etc.) Looking for remaining non-prompt tracks with p t >0.75 GeV/c and |cos  | < 0.5 Have verified that circle-fit Chisq behaves like a chisq (tracking conventions?); use chisq cut, but not very effective Require 4 or more hits; found track can have at most one hit from a different MCTRUTH source; otherwise labeled as fake

17. 263 “findable” tracks e + e -  qq at sqrt(s) = 500 GeV