1. Update on SP02 design by Victor Golovtsov & Lev Uvarov Trigger Meeting at Rice August 2002

2. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 2 Outline l GTLP Backplane Termination l FPGA Configuration l Boundary Scan

3. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 3 GTLP Backplane Termination Rephrasing the “Recommendation on GTLP bus Implementation”: è As shown in fig below, Vref is set by an R/2R resistor network between VTT and GND. è The resistor network maintains balanced upper and lower noise margins for any termination voltage fluctuations. So è Vref should be generated locally on each card è Since the termination network and VTT resides on the backplane, the card resistor network should take VTT from the BACKPLANE through a CCB connector pin. è SP02 design expects VTT to be available through B11 pin.

4. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 4 FPGA Configuration Modes SP02 carries 7 Virtex-II FPGAs on the main board plus 1 Virtex-II FPGA on the Mezzanine Card. Configuration Modes (selected by switchers) FPGA Boundary Scan Master Serial Master SelectMAP FrontYes VME/CCBYes DDUYes Main (SP)Yes

5. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 5 Boundary Scan Two tasks for boundary scan interface: è Testing the JTAG-compatible hardware for shorts and opens per IEEE 1149.1 (All Xilinx devices plus all GSI SRAMs, 65 devices total) è Configuring FPGAs per IEEE 1532 (All Xilinx device, 20 devices total) Three options to port to a local JTAG chain (chains): è Header for Xilinx’ Parallel Cable IV (2 mm pitch) è National SCANSTA111 Enhanced SCAN Bridge (one per SP02, supports up to 3 local chains). Uses the VME64x T&Mbus, but requires Boundary Scan Master in a Crate. è National SCANSTA101 Boundary SCAN Master (one per SP02, supports just one local chain). Requires a fuse-based CPLD for an auxiliary VME interface in each SP02. Third approach (with older 5V devices) has been successfully implemented in the first SP prototype. Second approach has been implemented and tested by Nuno Vaz Cardoso and Jose Carlos Da Silva from HC group.

6. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 6 Boundary Scan - continue They ported the SCAN Master functionality in the HDL form in the CPLD, built the VME card, as well as several test cards that used SCANSTA111 devices. They also built a GUI (wrapper) around National’s ScanEase software. The software used by both approaches is just the same. It is National’s command line utility ScanEase (Rev.2.0). Building a wrapper is a user’s problem. Needs to be mentioned here that both SCANSTA101 and SCANSTA111 are available either in silicon or in the HDL form. In the HDL form, each occupies about 15K gates. So, a big enough CPLD would carry both VME interface and SCANSTA functionality. Alex M. already got in touch with Ken Filliter from National, who provides support for SCAN devices and SCANEASE software.

7. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 7 Boundary Scan - continue Second approach has been implemented already in SP02 design, counting on already existed Boundary Scan Controller design at CERN. ( they schedule to launch production of their board this fall, so they could have ordered extra boards). But this may change if the third option finally prevails. In this case the JTAG interface will be redone.

8. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 8 Mezzanine Card Mezzanine card interfaces, as well as its dimensions are fully determined 6 Samtec FOLC/MOLC connectors carry 780 signals, 16 power and 84 ground pins. The card can accept either XC2V4000 or XC2V6000 devices. It is designed with auxiliary power and JTAG connectors to facilitate testing. The card image can be found on the “SP02 layout” slide.

9. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 9 SP02 Layout slide shows current status of the board. What’s new: è Two stiffeners from both sides of Front FPGAs è Switchers added, one per Xilinx device, for debugging purpose. è Backplane connectors moved a little bit, to be closer to corresponding drivers/receivers è DDU FPGA jumped to the next package size (from fg256 to fg456) è Number of buffers added to segment long traces è JTAG port implementation seems to be the only unresolved issue.

10. PNPI / University of Florida Design Status Aug 22, 2002. Victor Golovtsov, Lev Uvarov 10 SP02 Board Layout Phi Local LUT Eta Global LUT Phi Global LUT DC-DC Converter Indicators DDU FPGA TLK2501 Transceiver Optical Transceiver VME/CCB FPGA Main FPGA PT LUT Stiffener Front FPGA EEPROM Mezzanine Card ME1-to-DT MB1-to-SP To MS From CCB FM RJ45