Presentation is loading. Please wait.

Presentation is loading. Please wait.

Meshal Al-Rumaidhi Meshal Al-Rumaidhi Hassan Ghanim Ali Al-Haddad Hassan Ghanim Ali Al-Haddad Abdulrahman Habib Abdulrahman Habib Supervised by: Prof.

Similar presentations


Presentation on theme: "Meshal Al-Rumaidhi Meshal Al-Rumaidhi Hassan Ghanim Ali Al-Haddad Hassan Ghanim Ali Al-Haddad Abdulrahman Habib Abdulrahman Habib Supervised by: Prof."— Presentation transcript:

1 Meshal Al-Rumaidhi Meshal Al-Rumaidhi Hassan Ghanim Ali Al-Haddad Hassan Ghanim Ali Al-Haddad Abdulrahman Habib Abdulrahman Habib Supervised by: Prof. : Mohammed Fahim Prof. : Mohammed Fahim Eng. : Yousif Ali Eng. : Yousif Ali

2 Agenda Introduction Introduction Chlorohydrin Chlorohydrin Saponification and PO Recovery Saponification and PO Recovery By‐Product Disposal Section By‐Product Disposal Section Problem Involved Problem Involved The Principal Results The Principal Results Conclusion Conclusion

3 Introduction We estimated many factors and balances in the production of propylene oxide (PO) (50,659 Ib/hr) through propylene (C 3 H 6 ), chlorine (Cl 2 ) and water (H 2 O). These estimations will be simulated into HYSYS. Many data were collected from different resources to simplify the process.Our process consist of three sections: Chlorohydrin, Saponification and by-product disposal. We will describe each process briefly in the following slides.

4

5 Chlorohydrin Section

6 Chlorohydrin The first section is the chlorohydrin. we will describe the preparation of propylene chlorohydrin (PCH) which will converted to PO in the next section (Saponification section). Main: Sides:

7 Assumption Reactor: conversion 97%, 40 psia, 60 o C. Suitable fluid package used Wilson. Propylene and propane are recycled back. ComponentsMass Flow Rate (lb/hr) Propylene41,101 Propane3,744 Chlorine69,027 Water1,646,566

8 HYSYS Description The feed of chlorine and propylene is separated in fraction in (TEE‐100‐101); to produce specific value of PCH.

9 Chlorohydrin Section

10 In reactors (CRV‐100‐103) the feed enters at 40 o C and 60 psia with an assumed overall conversion of 97%; there are three reactions involved, the main one produce propylene chlorohydrins (PCH) but the two sides reaction produce propylene dichloride (PDC) and di-chloro-di-iso-propyl-ether (DCIPE). Since the liquid phase from each reactor is hot (Because the reaction is exothermic) so it cooled by heat exchanger (E‐100‐102) to 40 o C.

11 Chlorohydrin Section

12 The vapor phase are collected from above of each reactors in stream 4 (mainly H 2 O,HCl and un-reacted propane and propylene)

13 Chlorohydrin Section

14 The vapor stream is treating with two splitters (X‐100-101) to separate water and PDC by using NaOH and DCIPE respectively. the propylene and propane un‐reacted are recycled (Raw material cost)(# iteration 3)

15 Chlorohydrin Section

16

17 Saponification and PO Recovery

18 We will describe the production of propylene oxide (PO); by using the propylene chlorohydrin (PCH) formed in (Chlorohydrin) section.

19 Since data was insufficient, we were compelled to assume the conversion rate of the reactors as 99.9%. Pressure of feed that enters the conversion reactor is 22 psia and temperature of 99 o C. Assumptions Distillation Column

20 HYSYS Description We use conversion reactor and splitter instead of the try column because it consists of reaction and separator. The conversion reactor (99.9%) (CRV‐104), work at 99 o C 22 psia. there are two reaction involved, the main is to produced PO (Main product) and the other is to treat HCl acid produced in the first section. The vapor and liquid streams from the reactor are sending to splitter (X‐102) to separate undesired component such as: water and NaCl (Stream 15).

21 Undesired component such as: water and NaCl (Stream 15) Waste

22 The upper stream is cooled in (E‐104‐105) to make the liquid more; which will be the feed of distillation(T-100) and the vapor less; which will vented to atmosphere by using two phase separated (V‐100‐101); in first separator (V‐100) the liquid recycled(# iteration 3) to increased purity, but the vapor is sending to (V‐101).

23 There are three distillations columns in this section. First one (T-100) Used to separate PDC, DCIPE and Water from PO Assumption: (1) Reflux ratio 4, (Trays 22). (2) Distillate rate 57,500 Ib/hr (Vapor). (3) Recovery of PDC & DCIPE (0.999) and H 2 O (0.7) in liquid (LDIS 1). (4) Recovery of PO (0.99) in vapor (VDIS 1). (5) Press. drop 5 psia

24 Saponification and PO Recovery

25 Second distillation(T-101) used to separate PO from other component Assumption: (1) Reflux ratio 4, (Trays 22). (2) Distillate rate 54,700 Ib/hr (Vapor). (3) Recovery of other component (0.99) in liquid (LDIS 2). (4) Recovery of PO (0.999) in vapor (VDIS 2). (5) Press. drop 5 psia

26 Saponification and PO Recovery

27 Third distillation (T-102) used to achieved PO purity of 99.9% Assumption: (1) Reflux ratio 4, (Trays 10). (2) Distillate rate 50,700 Ib/hr (Liquid). (3) Recovery of other component (0.999) in vapor (Vent*). (4) Recovery of PO (1) in liquid (18). (5) Press. drop 5 psia

28 When the distillation process was complete, the exiting stream contained 50,659 Ib/hr of PO with purity of 99.9% (Near to what we have to get it 50,686 Ib/hr of PO with 99.9% purity) which mean the goal is achieved.

29

30 By-Product Section

31 By‐Product Disposal Section We will describe the separation of propylene dichloride (PDC) and (DCIPE) dichlorodiisopropylether. We separate these two components because we could sale and market them.

32 HYSYS Description The liquid distilled (LDIS1) is send to tow phase separator (V‐103); which used as a temporary storage for shutdown cases. The liquid stream is splinted by (X‐103) to purify PDC and DCIPE. Then we prepare the stream to send it to the distillations by cooling it with heat exchanger (E‐107) and use two phase separator (V‐104).

33 The first distillation(T-103) used to separate PDC and DCIPE from the other components Assumption: (1) Reflux ratio 4, (Trays 30). (2) Distillate rate 13200 Ib/hr (vapor). (3) Recovery of Water (0.8) in vapor (VDIS4). (4) Recovery of PDC & DCIPE (0.999) in liquid (DIS4). (5) Press. drop 5 psia

34 By-Product Section

35 The second distillation (T-104) used to separate PDC from DCIPE. Assumption: (1) Reflux ratio 4, (Trays 40). (2) Distillate rate 3750 Ib/hr (Liquid). (3) Recovery of PDC (1) vapor (22). (4) Recovery of DCIPE (1) in liquid (23). (5) Press. drop 10 psia

36 By-Product Section

37 When the distillation process was complete, the exiting vapor stream (22) contained 7217.8 Ib/hr of PDC is stored as by‐product. And the exiting liquid stream (23) contained 3708 Ib/hr of DCIPE which part of it stored as by‐product and the rest is recycled) (# iteration 3) to (X‐101).

38 Problem Involved First programming of PCH & NaCl in HYSYS: Adding a hypothetical component

39 Once we get the following screen, we build the structure of PCH C 3 H 6 OCl. We have to put the BP, MW, Tc, Pc, and VC

40 We add NaCl as solid hypothetical, so HYSYS need just molecular and density to identified the NaCl

41 Second problem, the pressure drop in reactors leads the vapor stream equal zero; to avoid this problem we decrees pressure and used internal heat exchanger in the reactor.

42 Third problem, when we recycled un‐reacted propylene and propane; HCl appeared in this stream so the amount of it reached millions Ib/hr. To fix this problem we put purge stream to avoid the accumulation HCl problem.

43 Fourth problem, the saponifire reactor is Tray Column reactor in HYSYS this reactor is not contained; so we use conversion reactor then the vapor and liquid stream are mixed in component splitter.

44 Fifth problem, the DCIPE (in stream 23) is recycled to the organic splitter with amount of 2000 Ib/hr; so we used purge stream as by‐product DCIPE to avoid accumulation and the rest about 1,982.9 Ib/hr send to the organic splitter.

45 The Principal Results ComponentsMass Flow Rate (lb/hr) Propylene41,101 Propane3,744 Chlorine69,027 Water1,646,566 Table. 1: Mass Flow Rate of Feedstock ComponentsMass Flow Rate (lb/hr) Propylene Oxide50,659 Propylene dichloride7,217.8 DCIPE3,708.7 Table. 2: Mass Flow Rate of Product & by-Products

46 The chlorohydrins process is useful technique to produce propylene oxide; this fact we noticed when we applied HYSYS simulation. In HYSYS we found the assumed amount of feed produce large quantity of PO, so we could sale this quantity and after that calculate the capital cost in the final report. Conclusion

47


Download ppt "Meshal Al-Rumaidhi Meshal Al-Rumaidhi Hassan Ghanim Ali Al-Haddad Hassan Ghanim Ali Al-Haddad Abdulrahman Habib Abdulrahman Habib Supervised by: Prof."

Similar presentations


Ads by Google