1. SIP Trunking Goldtel Aria – iP 60 ARIA IP - 60
What connection ? CO via GW or VoIB Card?
ARIA IP - 60

2. Introduction
This document explains the configuration that is required on ERICSSON-LG PABX systems when
SIP trunks are configured using the Goldtel SIP trunk service.
Basic call setup (Incoming & Outgoing calls) was tested with CLI (Calling Line Identification)
presentation.
Please note that this document is Service Provider specific (Goldtel Telecom) and some of the
Details below are used as examples only.
This document is only applicable to the ERICSSON-LG range of PABX systems.
Test Setup Configuration
Goldtel Service Provider Details
The following information was received from the Service Provider (Goldtel) to complete the tests:
 SIP/Proxy/Registrar IP: and
SIP Port Number : 5060 (UDP)
Sip account
Authorization Name
Password
Phone Number
cNxxxxxxxx

3. If we require 8 VoIP lines then this setting = 8
Slot Configuration
PGM
Right Click
If we require 8 VoIP lines then this setting = 8

5. Numbering Plan
PGM
What if theis is not [1]

6. IP Settings PGM 108 Gateway IP = Router IP PABX IP Address
ADSL Router IP Address
The same range as the PBX

7. CO Line Configuration
PGM 140/141/143/146

8. CO Line Configuration
Co grp 1 = Voip / SIP Trunks on Slot 10 (1st Choice o/g)
Telkom or other SP lines will be allocated to CO Grp2

9. CO Line Configuration Mode 141 Mode 146 Mode 142
This parameter defines the DID digit conversion process for DID digits received from the ISDN or IP CO line.
After removal of digits, Flexible button 5, the DID number treatment can be a simple conversion (0), no conversion (1) or simple conversion with table look-up (2). PGM231
FK1 COLP Connected Line Identity Presentation
This parameter defines the index to the COLP Table (PGM 201) used to determine the COLP sent by the system. If the index is 50, the COLP is determined from PGM 114, Flexible button 5.
CLIP Connected Line Identity Presentation
Calling Line Identification Presentation
FK4 ISDN Conversion Type This parameter defines the DID digit conversion process for DID digits received from the ISDN or IP CO line.
After removal of digits, Flexible button 5, the DID number treatment can be a simple conversion (0), no conversion (1) or simple conversion with table look-up (2).
(PGM146)
1 = Use digits as is
2 = Flex DID Table (PGM231)
FK5 DID Remove No This parameter defines the number of digits to remove from the DID number received. After digit removal, the ip can process a 2 to 4 digit DID number.
Digits are removed starting with the first received digit.
FK6 ISDN Enblock send If this parameter is ‘On’, dialed digits are sent using Enblock Sending, all digits are sent at once (user dials # or Enblock timer –PGM 182 Flexible button 10 expires). Otherwise, digits are sent using Overlap Sending, digits are sent as dialed. IP lines
must be assigned Enblock Sending.

10. CO Line Configuration Mode 146 CO Attr |||
FK1 When enabled (On), the My Area and Prefix codes (PGM 200, Flexible buttons 9 &10) are inserted in front of received CLI for incoming calls
FK2 When enabled (On), the My Area and Prefix codes (PGM 200 Flexible buttons 9 &
10) are inserted in front of the CLI for outgoing calls.
FK5 This parameter defines the number of DID digits the system expects to receive after digit removal (PGM 143, Flexible button 5).
FK6 DID Digit Mask
This parameter defines the DID digit conversion process (Digit Mask) for Type ‘0’ and ‘2’ DID Conversion/PGM231 (PGM 143, Flex 4). ‘# * * *’
2 to 4 digits 0 ~ 9, * and # # = delete digit

11. Station Configuration
PGM 111 for all extension
This parameter determines the caller id for a station when employing SIP for a call.
When using SIP, the caller id is based on the CLIP/COLP (PGM 143 Flexible button 1 and 2) or the User ID defined from the SIP User ID Table index (PGM 501) entered here.{500&501 with 340}
Invalid entry Message- Mode 111 FK23 = 1 Sip User ID
Also Mode The last 3 digits = 184 Open
Now set day & night destination ringing = 100

12. Station Configuration
PGM 111 for fax in and out going call

13. Station Configuration
PGM 114

14. VOIP Configuration PGM 340/341 Firewall IP = WAN IP of the Router
IP address of the Gateway Card VoIB
ADSL Router IP Address

15. PGM 340 SIP ATT 1 (Actually PGM 500)
VOIP Configuration
PGM 340 SIP ATT 1 (Actually PGM 500)

16. SIP Trunk Registration
PGM 340 SIP ATT 11 (Actually PGM 501)

17. Net working CO line configuration
PGM 322

18. COLP Table configuration
PGM 200/201

19. Flexible DID Table
PGM 231
Invalid entry Message- Mode 111 FK23 = 1 Sip User ID Error code “Cause 400”
Also Mode The last 3 digits = 184 Open
Now set day & night destination ringing = 100

20. COLP Table configuration
PGM 450 Flex 15
N.B. After this step please reset IP60 system

21. Mode 200 Mode 201 Mode 231 087 6300 551 Mode 143 – DiD=2 DiD REM = 1
DiD Enblock =1 On
Mode 146 – DiD RCV =3
DiD Dig = #***
#1**
Mode 231 – 550 – Ring Sta 100=150

22. END