1. Training

2. Terminology
Port- The connection to the server or pc. On sateon pro this is always ip field network-a group of controllers connected to port usually on 485 line header- an Ethernet/485 converter unit that allows a line of 485 controllers to be connected to a pc Enclosure- a power supply unit that allows up to two controllers or one controller and one ip board to be mounted in it.

3. Sateon Pro Controllers
System Setup Part 1 - Hardware
Cable Types
Data Comms
485 Data Comms
Ethernet Data Comms
Sateon Pro Controllers
485
Ethernet
Sateon Pro Enclosures

4. Line Header to Panel (Comms Converter)
Cable Types
Line Header to Panel (Comms Converter)
2 Pair Belden (or equivalent) # m per Segment
Cat 5 – Use Twists – Not for electrically noisy environments – 200m
Panel to Reader
See Reader Documentation 50m (if using Keypad Interface)
External Inputs
2 Core Cable (Alarm) m
Locks
Use suitable gauge cable for current draw and volt drop Current Draw (Amps) x Distance (Meters) x Wire Resistance per Meter (Ohms) = Voltage Drop (Volts)

5. Data Comms
485 Data Comms
SATEON PRO MINI PC
Ethernet Door Controllers

6. 485 Panels

7. 10 Panels on a line maximum Max 1200m No T taps / loops
Sateon Pro 485
RS-485
Two wire (plus Ground) – 1 Pair
10 Panels on a line maximum
Max 1200m
No T taps / loops
Each pair should be twisted
All controllers will need an Ethernet Line Header

8. Ethernet Line Header
Sateon Pro Line Header
Can be mounted in standard Enclosure

9. Data Line Overview
485 Panels are Polled 1 2 3 4
….. 10
Addresses do NOT have to be sequential
PORT connects a SATEON Comms Engine to Panels
SEGMENT - 1,200m length of Belden (2 or 4 wire)
Field Network - Cable from LINE HEADER to last Panel
10 Panels - address range 1 to 63

10. Ethernet Panels

11. Sateon Pro Ethernet
Panels are Polled and will immediately Synchronise with SATEON
Each IP Panel has it’s own IP address and connects directly to the network via a RJ45 Plug

12. Panel decides to unlock the door (or not)
PRO485 vs PRO ETHERNET
PRO 485 (Card Access)
Present Card
Panel decides to unlock the door (or not)
Waits for next Poll from SATEON PRO
Tells SATEON PRO about the card and access was allowed
PRO ETHERNET (Card Access)
Present Card
Panel decides to unlock the door (or not)
Tells SATEON about the card and access was allowed
485 (Input to Output on another Panel)
Activate input on Panel 1
Panel 1 waits for next Poll from SATEON PRO
Panel 1 tells SATEON PRO about the input activation
SATEON PRO broadcasts to Panel 2 to activate the output
PRO ETH (Input to Output on another Panel)
Activate input on Panel 1
Panel 1 tells SATEON about the input activation
SATEON broadcasts to Panel 2 to activate the output

13. Request To Exit contact must be N/O
Sateon Pro Panel Break Glass Monitoring
Request To Exit contact must be N/O
Break Glass Unit contact must be N/O

14. Sateon Pro Summary Intelligent Door Controller
485
TCP/IP
2 doors read in. 1 door read in/out
Additional alarm input
Card capacity 500 users
Real-time processing at door
LED and sounder outputs
Memory buffer whilst off-line (4,000 Events)
Upgrade flash whilst system is working
Volt Free Changeover output for Locks
Can be mounted in any PSU

15. Sateon Pro Controller Connections

16. Sateon Pro Lock Connections

17. Sateon Pro Reader Wiring

18. Sateon Pro Door Monitor Wiring
Door Sensor – Normally closed
Door Sensor – Normally closed - Monitored
Dual Door Sensor – Normally closed - Monitored

19. Request To Exit contact must be N/O
Sateon Pro Break Glass Monitoring
Request To Exit contact must be N/O
Break Glass Unit contact must be N/O

20. Sateon Pro Input Wiring
Input – Normally closed or Normally Open
Input – Normally closed or Normally Open

21. AES Encryption on eSeries Real-time processing
Sateon Pro Input / Output IO
RS485
TCP/IP
AES Encryption on eSeries
Real-time processing
Memory buffer whilst off-line (4,000 Events)
Upgrade flash whilst system is working
8in / 4out
Can be mounted in any Enclosure

22. Sateon Pro Input / Output 485 & Ethernet

23. EZ Enclosures

24. Sateon Pro Mains Enclosure
2 x Sat Pro board or 1 x Sat Pro board and 1x IO board
1 x 7Ah Battery
Built in tamper to lid
Built in power supply (3A) with 2A available for external equipment, i.e. locks and readers

25. Sateon Pro Mains Enclosure

26. Sateon Pro POE+ Enclosure
2 x Sat Pro Panel or 1 x Sat Pro Panel & 1x IO board
1 x 7Ah Battery
Built in tamper to lid
Built in power supply with 2A available for external equipment, i.e. locks and readers
POE 802.3af 44VDC 350mA 15.4W 900mA
POE at 44VDC 1700mA 25.5W 2000mA

27. EZ POE Enclosure

28. IP Panel IP Panel IP Panel Sateon Pro Hardware Overview
Up to 10 x RS485 Panels

29. Q&A Were you listening???
Question 1 - How long can a segment of the Comms line be?
Question 2 - What is the value of the EOL resistor that should be fitted to the beginning and end of the Comms line.
Question 3 - How many cards does the Sateon Pro board hold?
Question 4 – How many controllers does it support?
Question 5 - Can you wire a Sateon Pro485 board to a Sateon Pro IP?
Question 6 - How many Sateon Pro boards fit in an Enclosure?
Question 7 - What is the max Amps available for locking in an Enclosure?

30. Add a eSeries (IP) Panel Update the Firmware in a Panel Add a Door
System Setup Part 1 - Software
Install SATEON PRO
Licence SATEON PRO
Add a 485 Panel (I/O Board)
Add an Input
Add a eSeries (IP) Panel
Update the Firmware in a Panel
Add a Door
Add a Reader
Add a Person
Add Access
Add a Token
Unlock a door

31. Must change password on first logon Can change to sateon if you wish
SATEON - LOGON
Username : admin
Password : sateon
Must change password on first logon
Can change to sateon if you wish

32. SATEON Main Screen

33. Visitors not included on Sateon Pro
SATEON Hubs
Access Control
Control Centre
Reports
Event Configuration
System Configuration
Visitors not included on Sateon Pro

34. Apply the licence Verify the licence Setup the Token Type
SATEON – Initial Tasks
Apply the licence
Verify the licence
Setup the Token Type
Setup the Site Name
Setup the Comms Engine

35. Access Control – Token Management – Token Types - Add
SATEON – Create the Token
Access Control – Token Management – Token Types - Add

36. Access Control – Device Management - Site – Main Site
SATEON – Create the Site
Access Control – Device Management - Site – Main Site

37. SATEON Create the Comms engine
Access Control – Device Management - Comms Engine – Add

38. Will assign an address in 169.254.?.? Range if no DHCP available.
SATEON Programming Pro Devices
IP Panel or Line Header.
When supplied are DHCP.
Will assign an address in ?.? Range if no DHCP available.
Use the eSeriesDeviceProgrammer tool to set the IP address.
Encrypted devices will not come on line until ‘seeded’ using the eSeriesDeviceProgrammer tool with access to a valid SATEON licence.
eSeriesDeviceProgrammer will find devices in the same subnet and allow you to program them.
eSeriesDeviceProgrammer can be run from (and set the encryption of an Ethernet device) from any SATEON client machine (Config required)

39. SATEON EseriesDeviceProgrammer.exe

40. SATEON

41. A 485 Panel wires to a Field Network
SATEON
A 485 Panel wires to a Field Network
Each field network has at least one Port, the Port is the physical connection between the LAN / WAN and the Field Network.
A Field Network may have many Ports.
A Field Network may have 10 Panels.
Access Control – Device Management – Field Network– Add
Access Control – Device Management - Port– Add
Access Control – Device Management - Panel– Add

42. SATEON

43. SATEON

44. SATEON

45. Access Control – Access Management – Access Groups
SATEON
Access Control – Access Management – Access Groups

46. SATEON
Time schedules are used to define the periods during which things can happen within the SATEON access control system. For example;
When access is permitted at certain doors
When events are reported
When actions can occur.
A time schedule is set up as a combination of time patterns, where each time pattern defines one or more periods of time.
Each individual period of time with a defined start and end time is an appointment. Appointments can consist of an entire day.

47. Update the Firmware in a Panel Add a Door Add a Reader Add a Person
Recap
Install SATEON PRO
Licence SATEON PRO
Add a 485 Panel
Add a PRO(IP) Panel
Update the Firmware in a Panel
Add a Door
Add a Reader
Add a Person
Add Access
Add a Token
Unlock a door