Presentation is loading. Please wait.

Presentation is loading. Please wait.

Tutorial: Assembly Drawing Chapter 8. Standard Views INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009.

Published by Modified over 9 years ago

Similar presentations

Presentation on theme: "Tutorial: Assembly Drawing Chapter 8. Standard Views INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009."— Presentation transcript:

1 Tutorial: Assembly Drawing Chapter 8

2 Standard Views INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

3 Importing Dimensions INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

4 Design Intent: Assembly-Level Dimensions In an assembly drawing, only assembly-level features are dimensioned Showing component dimensions on an assembly drawing would be redundant. Double- dimensioning should always be avoided INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

5 Adding Exploded View INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

6 Hole Callout INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

7 Adding Bill of Materials INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

8 Adding Balloons Balloons relate bill of material items to components on drawing INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

9 Finished Drawing INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009

Download ppt "Tutorial: Assembly Drawing Chapter 8. Standard Views INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009."

Similar presentations

Chapter 12 Working Drawing

Chapter 12 Working Drawing
2010-2011.  Design Process  Technical Sketching  Line Conventions  English and Metric Measurement  Conversion in  mm & mm  in  Dial Calipers 

 Design Process  Technical Sketching  Line Conventions  English and Metric Measurement  Conversion in  mm & mm  in  Dial Calipers 
Introduction to Engineering Dimensioning - 3 Agenda Dimensioning cylinders and cones Locating holes and other features General guidelines.

Introduction to Engineering Dimensioning - 3 Agenda Dimensioning cylinders and cones Locating holes and other features General guidelines.
Dimensioning part 2 with SolidWorks

Dimensioning part 2 with SolidWorks
Tutorial: Bracket Chapter 3.

Tutorial: Bracket Chapter 3.
Dr Simin Nasseri, SPSU Tutorial: Pulley Chapter 2 Dr Simin Nasseri, SPSU Copyright of Howard and Musto, 2009.

Dr Simin Nasseri, SPSU Tutorial: Pulley Chapter 2 Dr Simin Nasseri, SPSU Copyright of Howard and Musto, 2009.
Engineering 1182 College of Engineering Engineering Education Innovation Center Feature-Based Modeling Part Editing Rev: 20140122, AJPFeature Based Modeling1.

Engineering 1182 College of Engineering Engineering Education Innovation Center Feature-Based Modeling Part Editing Rev: , AJPFeature Based Modeling1.
SDC PUBLICATIONS © 2011 Chapter 11 Assembly Drawings and Blocks Learning Objectives:  Create an Assembly Drawing from Part files.  Using AutoCAD with.

SDC PUBLICATIONS © 2011 Chapter 11 Assembly Drawings and Blocks Learning Objectives:  Create an Assembly Drawing from Part files.  Using AutoCAD with.
Tutorial: Advanced Assemblies

Tutorial: Advanced Assemblies
Tutorial: Business Card Holder

Tutorial: Business Card Holder
Tutorial: Handlebars Chapter 5. 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION.

Tutorial: Handlebars Chapter 5. 3-D Sketches Lines can be drawn in any of the three principal planes Use tab to toggle between XY, YZ, and ZX planes INTRODUCTION.
Tutorial: Hatch Assembly

Tutorial: Hatch Assembly
Tutorial: Drawing with Design Table Chapter 4. Multiple-Configuration Drawings Common for small components such as screws, nuts, O-rings, etc. Allows.

Tutorial: Drawing with Design Table Chapter 4. Multiple-Configuration Drawings Common for small components such as screws, nuts, O-rings, etc. Allows.
Tutorial: Drawings Chapter 2. Choose a Paper Size/Format Leave Unchecked for Plain Sheet INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009.

Tutorial: Drawings Chapter 2. Choose a Paper Size/Format Leave Unchecked for Plain Sheet INTRODUCTION TO SOLID MODELING USING SOLIDWORKS 2009.
Tutorial: Pulley Chapter 1.

Tutorial: Pulley Chapter 1.
Tutorials: Swept Geometries Chapter 5. Swept Boss/Base Two sketches are required: the path and the profile INTRODUCTION TO SOLID MODELING USING SOLIDWORKS.

Tutorials: Swept Geometries Chapter 5. Swept Boss/Base Two sketches are required: the path and the profile INTRODUCTION TO SOLID MODELING USING SOLIDWORKS.
Exploded View Extracting Drawings

Exploded View Extracting Drawings
Introduction to Assemblies Chapter 6. Assemblies Assembly files consist of multiple parts and the mates that define constraints between parts By default,

Introduction to Assemblies Chapter 6. Assemblies Assembly files consist of multiple parts and the mates that define constraints between parts By default,
Week 6 - Lecture Product Documentation

Week 6 - Lecture Product Documentation
Creating Solid Models Parametric Modeling Concept

Creating Solid Models Parametric Modeling Concept

Similar presentations

Ads by Google