Presentation is loading. Please wait.

Presentation is loading. Please wait.

A seminar On Validation Of Ampoule Filling & Sealing Machine

Similar presentations


Presentation on theme: "A seminar On Validation Of Ampoule Filling & Sealing Machine"— Presentation transcript:

1 A seminar On Validation Of Ampoule Filling & Sealing Machine
Department Of Quality Assurance Maliba Pharmacy College 19 April 2017

2 Introduction Validation may be defined as,
“The documented act of demonstrating that any procedure, process, and activity will consistently lead to the expected results which includes the qualification of systems and equipment” 19 April 2017

3 The equipment validation process generally covers following steps..
Continued…. The equipment validation process generally covers following steps.. User Requirement Specification (URS) Preparation of Design Qualification (DQ) Installation Qualification (IQ) Operational Qualification (OQ) Performance Qualification (PQ) 19 April 2017

4 Stages of Qualification

5 The previous figure depicts the most commonly used approach to the qualification process as used in the pharmaceutical industry It shows a pyramid, which is the best way in which to plan a qualification/validation project Investing more time in the first phases will save time and money in later and critical phases 19 April 2017

6 Who should do Equipment Validation?
The vendor or the user ? User has the ultimate responsibility for the accuracy of the analysis results and also for equipment qualification DQ should always be done by the user While IQ for a small and low cost instrument is usually done by the user, IQ for large, complex and high cost instruments should be done by the vendor OQ can be done by either the user or the vendor PQ should always be done by the user because it is very application specific, and the vendor may not be familiar with these PQ should be done on a daily basis 19 April 2017

7 Validation of Ampoule Filling & Sealing Machine
19 April 2017

8 19 April 2017

9 19 April 2017

10 Validation Protocol The entire process of equipment validation is designed in the form of certain documented formats or protocols This helps in systematizing the study of equipment validation A validation protocol prepared by engineer or validation specialist The protocol sections contain required procedures and forms 19 April 2017

11 Each protocol package is divided into three section:
Continued…. The procedure describe “how” the system is to be validated, while the forms document these procedure and provide a written record of the performed qualification and validation processes Each protocol package is divided into three section: Installation qualification (IQ) Operational Qualification (OQ) Performance Qualification (PQ) 19 April 2017

12 User Requirement Specification
The user of the equipment has certain requirement about the equipment which he wants to use Some of the general requirements may be stated in the form of certain parameters like… Size of equipment Speed of equipment Availability of spares, change part, immediate service at reasonable cost 19 April 2017

13 Continued…. Low sound generation Lesser breakdowns Materials of construction Auto control system This requirements are generally discussed with the suppliers and based on this discussion the selection of the equipment is done 19 April 2017

14 The size of delivery tube depend on ..
Continued…. For example, In ampoule filling machine, a delivery tube provided for repetitively forcing a measured volume of liquid through the orifice of delivery tube designed to enter the constricted opening of container The size of delivery tube depend on .. the opening of container the viscosity & density of liquid speed of delivery desired 19 April 2017

15 Preparation of D.Q. and its Certification
If we are going to purchase an standard equipment then the preparation of D.Q. dose not become very important because we are accepting the manufacturer's design as it is However, if a particular equipment is to be fabricated as per our requirements then the detailed D.Q. document become very important and essential 19 April 2017

16 Continued…. It is advisable to work out the detailed equipment specifications by sitting together with the equipment manufacturer It may also be advisable to perform Factory Acceptance Test (FAT) at the manufacturer’s premises before dispatch of the equipment to the purchaser 19 April 2017

17 Installation Qualification
“Installation qualification establishes that the instrument is received as designed and specified, that it is properly installed in the selected environment, and that this environment is suitable for the operation and use of the instrument” 19 April 2017

18 The qualification involves,
Continued…. The qualification involves, Verification of approved purchase order Verification of invoice Check manufacturer and supplier Verification of model number and serial number Checking for any physical damage Confirm location and installation requirements as per recommendation of manufacturers Verify that the utilities required are available Installation shall be conducted as per instructions provided in the manual 19 April 2017

19 Ensure all relevant documentation is received like,
Continued…. Ensure all relevant documentation is received like, User manual Maintenance manual List of change parts Electrical drawings 19 April 2017

20 Operational Qualification
O.Q. is verification of performance of the system without load O.Q. section details the tests to be performed on the equipment to document that it operates correctly O.Q. involve, Verification of alarm control Perform calibration requirements identified in the manual or established by the validation team Operate the equipment at low, medium, and high speed as per operations manual to verify the operating control Verify that all switches and push buttons are functioning properly Establish procedures (SOP) for operation, maintenance, and calibration Establish training program for relevant staff 19 April 2017

21 Performance Qualification
P.Q. is verification of performance of system with load Filling studies will be run on all containers and fill levels The containers will be filled in triplicate runs If a placebo is used, it should have similar physical characteristics (viscosity, density, foaming) to the actual fill materials The study should be run at minimum, maximum and intermittent speeds (in terms of ampoules/minute) The filler must handle the containers without damage and without jams Accuracy and precision must meet specifications 19 April 2017

22 P.Q. of ampoule filling and sealing machine involve,
Wight variation test Filling volume accuracy Particle Contamination Leaker test Oxygen content 19 April 2017

23 Weight variation test :
In the absence of specific criteria, weight variation must conform to USP In summary, all 10 units must be within 85.0 to 115.0% of target content, with a %RSD ≤ 6.0%, or not more than 1 of the 30 units outside of the 85.0 to 115.0% and no units outside of 75.0 to 125.0%, with a %RSD ≤ 7.8% 19 April 2017

24 Filling Volume Accuracy:
Continued….. Filling Volume Accuracy: The filling accuracy should be within ±% of the adjusted and desired filling volume in accordance with the machine specification. eg. Attention limit: ±1% Action limit: ±2% 19 April 2017

25 Particle Contamination of Ampoules during Filling & Sealing Procedure:
Continued…. Particle Contamination of Ampoules during Filling & Sealing Procedure: Ampoules should be filled with water for injection and afterward be inspected on the contamination with particles (particle classes: ≤10 μm and ≤25 μm). The inspection can be performed with a particle counter. 19 April 2017

26 Continued…. Leaker test: Should capillary pore or tiny cracks be present, micro-organisms or other contaminants may enter the ampoule, or the content may leak outside. Leaker usually detected by submerged ampoule in a deeply colored dye solution (usually 0.5 to 1.0% methylene blue). Limitation is that capillaries of about less than 15 um not detected by this method. 19 April 2017

27 Continued…. Oxygen content, If the filler produces a nitrogen purge, the headspace gas should be analyzed for oxygen content 19 April 2017

28 Requalification Requalification of systems and equipment should be done in accordance with a defined schedule The frequency of requalification may be determined on the basis of factors such as the analysis of results relating to calibration, verification and maintenance There should be requalification after changes The extent of requalification after the change should be justified based on a risk-assessment of the change 19 April 2017

29 References... R. A. Nash & A. H. Wachter, “Pharmaceutical process validation”; Third edition Leon Lachman, H. A. Lieberman & J. L. Kanig, “The Theory and Practice of Industrial Pharmacy”; Third edition, Pg. No to 674 Manohar A. Potdar, “Pharmaceutical Quality Assurance”, Pg. No , 8.14 Syed Imtiaz Haider, “Validation Standard Operating Procedure”, Pg. No to 307 Syed Imtiaz Haider, “Pharmaceutical Master Validation Plan”, Pg. No. – 140 19 April 2017

30 THANK YOU…. 19 April 2017


Download ppt "A seminar On Validation Of Ampoule Filling & Sealing Machine"

Similar presentations


Ads by Google