1. “Manufacturing” From Refined Steel Material to Shaped Product CON 251 Metals Processing

2. Shaped Products The product may be intermediate, as in a rolled steel beam prior to “fabrication” The product may be final, as in a steel casting for a bridge saddle or a bollard

3. Manufactured Steel Products Two basic categories of manufactured steel products: Cast Steel Products made in one basic way in foundries. (Molten metal cast into finished shape) Wrought Steel Products made one of several methods in mills. (Shaped through deformation)

5. Casting Casting is generally performed by pouring molten steel into sand molds. Casting is used instead of wrought methods when the steel product to be made is of such size and/or complexity that it is uneconomical to produce by other methods. Example (big):Bridge saddles, ship anchors, mooring cleats, bollards

6. Cast Bars & Engine Block

7. Wrought Steel Products (Formed Through Deformation) Forging - ( Hammering into shape) Extruding - ( Squeezing through a shaped die) Hot Rolling - Progressive forming with various rolls. (with or without cold finishing)

8. Forging Forging: Method of forming hot metal by squeezing between heat-resistant dies. Open-Die Forging: A large press squeezes (not strikes) steel between two heat-resisting surfaces…can be used to shape very large steel ingots (the ingot may weigh several hundred tons, the forge can squeeze with a force of several thousand tons) Closed-Die Forging: A large hammer pounds the steel between two heat-resisting shaped dies until the product is in the desired shape

9. Forged Steel Parts

10. Extrusion Extruding: Method of converting semi-finished shapes into lengths of uniform cross-section by forcing preheated, plastic steel through a very tough, heat- resistant die (analogy: toothpaste) Bars, tubing, pipes, and many unusual cross-sections can be extruded. More complex shapes can be extruded than can be rolled. More economical for small quantities than other forming methods. A limitation is that cross-section must be uniform. Therefore, Plain round bars could be extruded or rolled, but Ribbed round bars (like rebar) could not be extruded, must be rolled

11. Aluminum Extrusions

12. Hot Rolling Hot Rolling: Used to make semi finished shapes as well as some finished products. May be started with reheating of large steel ingots from steel producer, or may be sequenced directly after the continuous strand casting process. Hot steel passes through a system of heat-resistant rolls which gradually, roll by roll, change the ingot or strand into one of three basic intermediate shapes: Slabs: Flat, rectangular shapes with width > 2x thickness; Will later become plates, sheets, strips, or products like pipe and tubing (made from plates, sheets, strips) Blooms: Rectangular cross-sections, generally larger than 36 sq. in.; Will later become structural shapes, rails, seamless pipe Billets: Rectangular cross-sections, less than 36 sq. in. Will later become bars (including rebar), rods, wire

13. Hot Rolling I & H Beams

14. Rolled Sheet & Rail

15. Coiled & Straight Re-bar

16. Hot & Cold Finishing Hot Finishing: (Hot Rolling) This is basically a continuation of hot rolling, where the semi- finished product continues while still hot through more rolls to become the finished structural shape, rail, plate, bar, sheet, etc. Cold Finishing: (Cold Rolling) Transition from semi-finished to finished product via room- temperature finishing processes such as rolling, reduction, drawing:

17. Cold Finishing Processes Prior to the cold finishing processes, the semi- finished products from the initial hot-rolling steps must be “cleaned up” by: Descaling: This is removal of the surface oxide scale, usually by a process involving dipping in sulfuric or hydrochloric acid (this process is known as pickling) Rinsing: with both hot and cold water Drying: usually using steam Oiling: as a temporary sealant and lubricant, in preparation for cold finishing

18. Cold Rolling Cold Rolling: passing the semi finished metal through another series of rolls to impart desired final shapes and/or mechanical properties and surface finishes Cold Reduction: actually another type of cold rolling, but specifically to drastically reduce the thickness of an already-flat hot-rolled product (such as sheets or strips) in order to improve strength, finish, flatness Example: Half-dollar thick, ¾-mile long steel strip + 20 minutes of cold reduction = playing-card thick, 2-mile long strip Cold Drawing: making smaller cross-sections (small bars or wire) from hot- rolled bars or rods by pulling the latter through a hard, abrasion-resistant die…cold drawn wire can achieve tensile strength of 500ksi.

19. Protective Finishes Protective Finishes: Metallic Coatings Vitreous Coatings Laminated Coatings Painted Coatings Needed to protect from corrosion

20. Metallic Coatings Hot dip processes (submerging in molten bath): Galvanizing – heavy coating with zinc Aluminizing – coating with aluminum/silicon Tin, others Electroplating (electrolytic metal transfer) Metallizing (spraying molten metal onto surface to be coated) Cladding (direct application of thin sheet of coating metal)

21. Vitreous Coatings Glass-on-steel linings for process piping, tanks Porcelain enamel coatings on building panels, plumbing fixtures

22. Laminated Coatings Thin, tough plastic films applied with thermosetting adhesives

23. Painted Coatings Petroleum Based Water Based Epoxy Based

24. Two basic types: Oxidation (Ferrous metals): Iron reacts with oxygen, forming iron oxide (rust) Galvanic (Dissimilar metals): Creation of an electrolytic cell (water & dissolved minerals are typically the electrolyte) One metal becomes the positive electrode (anode)… oxidation & loss of material One metal becomes the negative electrode (cathode)… reduction & gaining of material Corrosion

25. Magnesium, Aluminum Zinc, Iron Steel, Cast Iron Lead, Brass Copper, Bronze Nickel, Stainless steel Silver, Graphite Example: sacrificial zinc anodes on marine steel hulls Corrosion can be impeded by: coatings, alloying, and other methods Galvanic series

26. Sacrificial Anodes