1. 04/26/2011Marshall Electronics, Inc. © 20111 H.264 Cameras and Servers Sales & Technical Training Presented By: Jim LucasNigel Hamley, MBKS Product ManagerManager – Technical Support & Pre-Sales Marshall Electronics

2. 04/26/2011Marshall Electronics, Inc. © 20112 H.264 Product Training Hands on Training How to Demo the Product to a Customer

3. 04/26/2011Marshall Electronics, Inc. © 20113 Point-to-Point Demonstration Check List 1. Marshall VS-540 Camera with Power Supply 2. Marshall VS-102 Server with Power Supply 3. Cisco 5 Port Switch with Power Supply 4. Marshall HDSDI Monitor with Power Supply 5. Power Strip 6. 3 or more Cat5 (RJ45-RJ45) Cables 7. 2 or more Video (BNC-BNC) Cables 8. True Manager Software (V1.0.2.8) 9. Computer with NIC Connection

4. 04/26/2011Marshall Electronics, Inc. © 20114 Hooking it Up (Don’t Connect it yet) Video SDI Network HDSDI 1 HDSDI 2

5. 04/26/2011Marshall Electronics, Inc. © 20115 Setting Up the Computer DHCP Vs Static IP DHCP means “Dynamic Host Configuration Protocol”, and for our purpose means that the IP (Internet Protocol) Address is set automatically by a Gateway or Router when you connect your Computer up to the Internet Static IP Addresses are Manually set. DHCP IP Address can change as they are automatically set, you take a computer off-line and add it back later after others have joined the Network and your address will not be the same. Static IP Addresses do not change. This is Important to us because we want our Camera/Server to always have the same address so we can easily find it on the Network.

6. 04/26/2011Marshall Electronics, Inc. © 20116 Hooking it Up Connect the Computer to the Switch Video SDI Network

7. 04/26/2011Marshall Electronics, Inc. © 20117 Setting Up the Computer Static IP Network Go to Control Panel and open Network Connections When you connect the Switch you will see your Computer Acquired the Device. The Computer in this example has a Dual NIC (Network Interface Card) so it can support both a Static and DHCP Network at the same time.

8. 04/26/2011Marshall Electronics, Inc. © 20118 Setting Up the Computer Static IP Network Right Mouse Click the Local Area Network Connection, highlight the Internet Protocol (TCP/IP) and Click on Properties It will reveal the Internet Protocol Properties Page, this is most likely how it will look set up for DHCP

9. 04/26/2011Marshall Electronics, Inc. © 20119 Setting Up the Computer Static IP Network Click on “Use the following IP address” and the fields will show up blank Fill in the IP Address 192.168.1.99 and the Subnet mask will populate automatically. Click OK, and OK again to close out of the next screen

10. 04/26/2011Marshall Electronics, Inc. © 201110 Hooking it Up Connect the Camera to the Switch Video SDI Network HDSDI 1

11. 04/26/2011Marshall Electronics, Inc. © 201111 Install True Manager Software (V 1.0.2.8) Make a File Folder using Windows Explorer on the “C” Drive that is called “True Manager” Copy the Program File “True Manager” from a CD or USB Drive into this File Folder. Right Click the Program File and Send to the Desktop (Create Shortcut)

12. 04/26/2011Marshall Electronics, Inc. © 201112 Using True Manager Setting up the Camera Click on the “True Manager” Icon you landed on the Desktop and click “Run”, it will launch the application below. Note the Menu Items on the Top, Click Server, then IP Discovery.

13. 04/26/2011Marshall Electronics, Inc. © 201113 Click on the “Discover” Button. IP Discovery populates with the Camera Details, the IP address from the factory is always the same 192.168.10.100. Using True Manager Setting up the Camera

14. 04/26/2011Marshall Electronics, Inc. © 201114 Using True Manager Setting up the Camera Highlight the Camera’s String of Data Click “IP Change and the IP Address Change Window will appear.

15. 04/26/2011Marshall Electronics, Inc. © 201115 Using True Manager Setting up the Camera Change the IP Address to : 192.168.1.140 and the Gateway to 192.168.1.1 Click “Change” and you will be returned to “True Manager’s” Home Page

16. 04/26/2011Marshall Electronics, Inc. © 201116 Using True Manager Setting up the Camera Go to the Menu, Server, and then IP Discovery. Highlight the String and Click “Select”. Now give the Server (Camera) a Name, VS-540_CAMERA_1, you can change the ID and Password but we’ll leave the Default ID = admin, Password = 1234. Click “Add” and Close the IP Discovery Window.

17. 04/26/2011Marshall Electronics, Inc. © 201117 Using True Manager Setting up the Camera We are returned to the “True Manager” Home Page and we can see our Server (Camera) is “Disconnected”. Check the Box in front of the IP Address.

18. 04/26/2011Marshall Electronics, Inc. © 201118 Using True Manager Setting up the Camera You can see here that the Camera is now connected to the Network and is “On Line”. We can exit True Manager. File, Exit.

19. 04/26/2011Marshall Electronics, Inc. © 201119 Setting Up the Camera From the Browser You can only use Internet Explorer as a Browser log into the Camera by entering this the Address Field http://192.168.1.140. Fill in the User name = admin and the Password 1234, if you want the Password to be remembered on this Computer, check the feature, click OK

20. 04/26/2011Marshall Electronics, Inc. © 201120 Setting Up the Camera From the Browser If this is the first time you’ve logged onto one of the H.264 products you will see the screen below asking you to Install the “Marshall ActiveX Application”. Click “OK”

21. 04/26/2011Marshall Electronics, Inc. © 201121 Setting Up the Camera From the Browser Note the ActiveX Information Bar, Click to Install, Select “Install ActiveX Control….” An Internet Explorer Security Warning will appear, Click “Install” to Install the Marshall Electronics ActiveX Application

22. 04/26/2011Marshall Electronics, Inc. © 201122 Setting Up the Camera From the Browser Should you have difficulty in opening the Web Page or you don’t get asked to Install the “Marshall ActiveX Application” you may have a corrupted “ActiveX” or it may be from an old Firmware Version. To solve this delete the “ActiveX” dll from the Windows System 32 Directory – “tvsl.dll” When deleted close out the Windows System 32 Directory and try to open Internet Explorer and Log onto the Camera.

23. 04/26/2011Marshall Electronics, Inc. © 201123 Setting Up the Camera From the Browser Only use Internet Explorer as a Browser log into the Camera by entering this the Address Field http://192.168.1.140. Click Setuphttp://192.168.1.140

24. 04/26/2011Marshall Electronics, Inc. © 201124 Setting Up the Camera From the Browser Set-up You can see a number of menu items across the top, System, Video, Audio, Network, Serial, Event, Preset, Record, User, and Camera. We will go through just the basics in this Training Session. Next we will set the System Page Up.

25. 04/26/2011Marshall Electronics, Inc. © 201125 Setting Up the Camera From the Browser Set-up Put a Name in for the System ID. VS-540_CAMERA_1, Click “Apply”. Change the Time, Click “Set Current Time” Change the “Time Zone” to Pacific Time, Click “Apply”. Click the Menu Tab “Video” at the top.

26. 04/26/2011Marshall Electronics, Inc. © 201126 Setting Up the Camera From the Browser Video - Part 1 You can change the Bitrate to 2000 You can change the Output Resolution by pulling down the tab on the right. The Preference is either Bitrate (CBR) or Quality (VBR). Most Cases use Bitrate. Switch on the Dual Encode for a send stream of H.264 at a lower Bitrate.

27. 04/26/2011Marshall Electronics, Inc. © 201127 Setting Up the Camera From the Browser Video - Part 2 In Information Display you can check “On” the “System ID” and Time. Go to “Live View” to see how they look.

28. 04/26/2011Marshall Electronics, Inc. © 201128 Setting Up the Camera From the Browser Video - Part 3 The H.264 Products offer either a Secondary H.264 Stream (Dual Encode) or a Local Video Output. Enable Video Preview from the Encode Menu. (Top) Set the desired Video Output – Resolution and Frame Rate from the “Output Format” Menu. (Bottom)

29. 04/26/2011Marshall Electronics, Inc. © 201129 Setting Up the Camera From the Browser Audio Not much to adjust here, however it’s important to remember which Audio Algorithm you used because the Decoder must be set the same way, even if there is no Audio.

30. 04/26/2011Marshall Electronics, Inc. © 201130 Setting Up the Camera From the Browser Network - Part 1 Not much to set here for normal operations Make sure that the Base Port is: 2222 HTTP Port is: 80 RTSP Port is: 554 Use this a Default Page

31. 04/26/2011Marshall Electronics, Inc. © 201131 Setting Up the Camera From the Browser Network - Part 2 If you were using this to encode a feed for “Multicast” you would insert the appropriate IP Address here.

32. 04/26/2011Marshall Electronics, Inc. © 201132 Setting Up the Camera From the Browser Serial If you have an external PTZ (Pan, Tilt and Zoom) Controller this is where you would set up the Communications Protocol.

33. 04/26/2011Marshall Electronics, Inc. © 201133 Setting Up the Camera From the Browser Event - Part 1 This Page is primarily for setting the Camera up in a Security Environment where Alarm Conditions can be set E-mail Notification can be set up if the Camera receives a Breach in Security.

34. 04/26/2011Marshall Electronics, Inc. © 201134 Setting Up the Camera From the Browser Event - Part 2 More Security features including the ability to upload Video to a Remote FTP Site

35. 04/26/2011Marshall Electronics, Inc. © 201135 Setting Up the Camera From the Browser Preset You can set up Preset Positions. Click the Radio Check Box in #1 Label, Zoom all the way out, Click Set. Click the Radio Check Box in #2 Label, Zoom all the way in, Click Set Click Save List Click either Position, Click Go to and it will go to that location.

36. 04/26/2011Marshall Electronics, Inc. © 201136 Setting Up the Camera From the Browser Record This is used to set up Video Recordings

37. 04/26/2011Marshall Electronics, Inc. © 201137 Setting Up the Camera From the Browser User This is page sets up more Secure Login Credentials to get into the Setup of the Camera.

38. 04/26/2011Marshall Electronics, Inc. © 201138 Setting Up the Camera From the Browser Camera This is the Setup of the Camera, Day & Night Mode White Balance Exposure ETC – Allow for the Digital Zoom to be switched off. As the Digital Zoom just increases Pixel Size, switching this feature off will be popular with the Broadcaster. As it maintains higher Quality

39. 04/26/2011Marshall Electronics, Inc. © 201139 Hooking it Up Connect the Decoder to the Switch Video SDI Network HDSDI 1 HDSDI 2

40. 04/26/2011Marshall Electronics, Inc. © 201140 VS-102 Setting up the Decoder We will now set up the VS- 102 which can be either a Encoder or Decoder (User Switchable by Software) Important, certain settings, including all applied settings when we go to the Browser create a Reboot. The Box has not completed its Reset until the “Status” Light is flashing, Usually the other Lights are also on.

41. 04/26/2011Marshall Electronics, Inc. © 201141 Using True Manager Setting up the Decoder Click on the “True Manager” Icon you landed on the Desktop, it will launch the application below. Note the Menu Items on the Top, Click Server, then IP Discovery.

42. 04/26/2011Marshall Electronics, Inc. © 201142 Click on the “Discover” Button. IP Discovery populates the Decoder Details, the IP address at the top, the IP address from the factory is always the same 192.168.10.100. Using True Manager Setting up the Decoder

43. 04/26/2011Marshall Electronics, Inc. © 201143 Using True Manager Setting up the Decoder Highlight the Decoder’s String of Data Click “IP Change and the IP Address Change Window will appear.

44. 04/26/2011Marshall Electronics, Inc. © 201144 Using True Manager Setting up the Decoder Change the IP Address to : 192.168.1.102 and the Gateway to 192.168.1.1 Click “Change” and you will be returned to “True Manager’s” Home Page

45. 04/26/2011Marshall Electronics, Inc. © 201145 Using True Manager Setting up the Decoder Go to the Menu, Server, and then IP Discovery. Highlight the String and Click “Select”. Now give the Decoder a Name, VS-102_DECODER_1, you can change the ID and Password but we’ll leave the Default ID = admin, Password = 1234. Click “Add” and Close the IP Discovery Window.

46. 04/26/2011Marshall Electronics, Inc. © 201146 Using True Manager Setting up the Decoder We are returned to the “True Manager’s” Home Page and we can see our Decoder is “Disconnected”. Check the Box in front of the IP Address.

47. 04/26/2011Marshall Electronics, Inc. © 201147 Using True Manager Setting up the Decoder You can see here that the Decoder is now added and connected to the Network and is “On Line”. We can exit True Manager. File, Exit.

48. 04/26/2011Marshall Electronics, Inc. © 201148 Setting Up the Decoder From the Browser You can only use Internet Explorer as a Browser log into the Camera by entering this the Address Field http://192.168.1.102. Fill in the User name = admin and the Password 1234, if you want the Password to be remembered on this Computer, check the feature, click OK

49. 04/26/2011Marshall Electronics, Inc. © 201149 Setting Up the Decoder From the Browser Set-up You can see a number of menu items across the top, System, Video, Audio, Network, Serial, Event, Preset, Record, User, and Camera. We will go through just the basics in this Training Session. Next we will set the System Page Up.

50. 04/26/2011Marshall Electronics, Inc. © 201150 Setting Up the Decoder From the Browser Set-up Change System Mode to “Decoder” Put a Name in for the System ID. VS-102_DECODER1, Click “Apply”. Change the Time, Click “Set Current Time” Change the “Time Zone” to Pacific Time, Click “Apply”. Click the Menu Tab “Video” at the top.

51. 04/26/2011Marshall Electronics, Inc. © 201151 Setting Up the Camera From the Browser Video Change the Output Format to 1080/50.94

52. 04/26/2011Marshall Electronics, Inc. © 201152 Setting Up the Camera From the Browser Audio Not much to adjust here, however it’s important to remember which Audio Algorithm you used with the Source because the Decoder must be set the same way, even if there is no Audio.

53. 04/26/2011Marshall Electronics, Inc. © 201153 Setting Up the Camera From the Browser Network - Part 1 Not much to set here for normal operations Make sure that the Base Port is: 2222 HTTP Port is: 80 RTSP Port is: 554 Use this a Default Page

54. 04/26/2011Marshall Electronics, Inc. © 201154 Setting Up the Decoder From the Browser Network - Part 2 Enter the IP Address of the Source (Encoder) in our case the Camera in the Remote Address Field – 192.168.1.140

55. 04/26/2011Marshall Electronics, Inc. © 201155 THANK YOU Marshall Electronics