1. SmartLine
Startup

2. Initial wirings
SmartLine
Initial Wirings

3. Balance Zones with a 3.9kΩ resistance
Initial wirings
SmartLine
Balance Zones with a 3.9kΩ resistance

4. If Zones aren’t balanced panel displays “Zone open”
Initial wirings
SmartLine
Fault /04
Zone Open
Zone
<Zone 01>
If Zones aren’t balanced panel displays “Zone open”

5. Balance Dialler with a 10 kΩ resistance (between terminals 19 and 23 )
Initial wirings
SmartLine
Balance Dialler with a 10 kΩ resistance (between terminals 19 and 23 )

6. If Dialler isn’t balanced panel displays “Fault Dialler”
Initial wirings
SmartLine
Fault /01
FaultDialler
If Dialler isn’t balanced panel displays “Fault Dialler”

7. Initial wirings
SmartLine
Balance NAC
with a 47kΩ resistance

8. panel displays “Open I/O Panel NAC”
Initial wirings
SmartLine
Fault /01
Open I/O
Panel NAC
If NAC isn’t balanced
panel displays “Open I/O Panel NAC”

9. SmartLine Detectors Wiring
Balance other zones with a 3.9 kΩ resistance
3.9 kΩ End of Line resistance on the last detector

10. SmartLine Callpoints Wiring
Balance other zones with a 3.9 kΩ resistance
3.9 kΩ End of Line resistance on the last callpoint

11. NAC output activates on Alarm: it can activate alarm devices
SmartLine
NAC Wiring
NAC output activates on Alarm: it can activate alarm devices
47 kΩ End of Line resistance on the last device

12. NAC
SmartLine
Fault /01
Short I/O
Panel NAC
If panel displays “Short I/O Panel NAC” it will need connect a diode in series (if devices haven’t it)
47 kΩ End of Line resistance on the last device

13. SmartLine Other wirings 17-18 FAULT Terminals activated on Fault.
Fault output can activate some devices

14. SmartLine 19-20 DIALER Terminals activated on Alarm.
DIALER Output can activate an external dialler.

15. SmartLine 25-26 AUX R Terminals turn off 24V on Reset
They can reset latching linear beam smoke detector

16. SmartLine 27-28-29 RELAY Terminals activated on Alarm (at default)
They can activate some devices

17. Generic Contact Wiring
SmartLine
Generic Contact Wiring
Alarm contact only
680Ω resistance
NO Alarm Contact
3.9kΩ resistance

18. Alarm Contact and Fault Contact
Generic contact
SmartLine
Alarm Contact and Fault Contact
680Ω resistance
NO Alarm Contact
NC Fault Contact
3.9kΩ resistance

19. Detection-Line Zone Wiring
Gas Detector Wiring
SmartLine
Gas Detector Wiring
Detection-Line Zone Wiring
It have to program the Zone as “Gas (Relay Output)
INE55/ING55 Detector
3.9kΩ resistance

20. SmartLine I/O 4-20mA Input Wiring
Gas Detector Wiring
SmartLine
I/O 4-20mA Input Wiring
It have to program I/O Line as “Gas 4-20mA Input”
INA55-101
board
150Ω resistance
INE55/ING55
Detector
3.9kΩ zone balancing resistance

21. Generic 4-20mA Gas Detector Wiring
SmartLine
Generic 4-20mA Gas Detector Wiring
It have to program I/O Line as “Gas 4-20mA Input”
Generic 4-20mA gas detector
4-20mA output
150Ω resistance
3.9kΩ zone balancing resistance
Detector have to supply current

22. Expansion Boards Wiring
SmartLine
Expansion Boards Wiring
To next expansion board

23. SmartLine Expansion Zones are similar to panel ones
Expansion boards
SmartLine
Expansion Zones are similar to panel ones
Balance Zones with a 3.9kΩ resistance

24. Espansions board
SmartLine
Expansion NAC output is programmable (at default output is activated on Alarm)
Balance NAC with a 47kΩ resistance

25. SmartLine It have to configure expansion boards
Control Panel
IN PROGRAMMiING
Ver: 2.03
01/01/ :45
Enable panel programming phase

26. SmartLine Expansion boards Control Panel IN PROGRAMMING Ver: 2.03
01/01/ :45
Control Panel
IN PROGRAMMING
Ver: 2.03
01/01/ :45
Settings
Disablement
Maintenance
Programming
Configuration
Progr. Zone
Progr. Output
Progr. Timer
Acquire int.bus
Acquire ext.bus
Current Devices
Extin.module O
Expansion O
Ok to execute
Current Devices
Extin.module O
Expansion
Ok to execute

27. SmartLine RS485 Bus Wiring Up to 4 Repeater 2 Power Station RS485 Bus
SmartLevel Power Station
SmartLetUSee/LCD-Lite Repeater

28. SmartLine It have to address RS485 Bus devices RS485 Bus Address
DIP Switch Position
SmartLevel Power Station
SmartLetUSee/LCD-Lite Repeater

29. SmartLine It have to address RS485 Bus devices RS485 Bus
Enable SmartLevel programming phase
Prog
View log
LED Test
Reset
Maintenance
LED test
Reset
Maintenance
Programming
Booster
Options
Address RS485
Default Data
SmartLevel Power Station
Address: 01
SmartLetUSee/LCD-Lite
Repeater
Address: 02

30. SmartLine Set End of Line jumper in EOL position on the last device
RS485 Bus
SmartLine
Set End of Line jumper in EOL position on the last device
SmartLevel
Repeater
SmartLevel Power Station
Ripetitore SmartLetUSee/LCD-Lite

31. SmartLine It have to address RS485 Bus devices
Control Panel
IN PROGRAMMING
Ver: 2.03
01/01/ :45
Enable panel programming phase
SmartLevel Power Station
SmartLetUSee/LCD-Lite Repeater

32. SmartLine RS485 Bus SmartLevel Power Station
Centrale
IN PROGRAMMAZ.!!
Ver: 2.03
01/01/ :45
Control Panel
IN PROGRAMMING
Ver: 2.03
01/01/ :45
Control Panel
IN PROGRAMMING
Ver: 2.03
01/01/ :45
Settings
Disablement
Maintenance
Programming
Configuration
Progr. Zone
Progr. Output
Progr. Timer
Acquire int.bus
Acquire ext.bus
SmartLevel Power Station
Current Devices
Repeater O
Power Station O
Ok to execute
SmartLetUSee/LCD-Lite Repeater
Current Devices
Repeater 2
Power Station 1
Ok to execute