1. Rolling element bearings A. Lozzi 09
For a given shaft diameter:
The general rule to meet higher load requirements is to try to use more rolling elements, elements of larger diameter and or more concave tracks
To meet the requirements of higher speeds, reduce contact stresses ie use lighter loads and elements of smaller contact patch. (eg bigger balls on flatter tracks). The smaller the patch, the more nearly will the motion of the rolling element on the tracks be purely rolling.
There are minimum loads below which bearings cannot be guaranteed to roll and not slide on their tracks. Hence reducing loads to permit higher speed and or to prolong life have limits.

2. For a given standard shaft diameter there is a range standard housing bore diameters that can be accommodated with bearings of higher wall heights.
Likewise for given bore diameters there are a range of shaft diameters that can be accommodation. Further for given shaft and bore diameters there are a range of bearing widths that can be used. This range of heights and widths of bearings are referred to as bearing ‘series’.

3. Looking at bearings for a shaft diameter of 50mm, we see that outer diameters from 65 to 130 mm can be accommodated.
For increasing outer diameters the dynamic load rating increases. Note that the width of these bearings also increases from 7 to 31 mm. These are standard series bearings.
This table also shows that for a given bearing ID and OD there are choices of bearing widths. For example 50 ID, 80 OD there are two widths possible: 10 & 16 mm.
There are ranges of bearings not shown in standard catalogues that are referred to as narrow and very narrow series, for which one typically pays considerably more.

4. Note that in the space taken up by a 50 ID, 110 OD &27 mm wide deep groove ball bearing, shown on the previous slide, we could substitute a twin row self aligning ball bearing, or a twin row spherical rollers (also self aligning) ball bearing. These 3 bearings would have quite different axial and radial load bearing characteristic and angular aligning requirements. The cost will also differ significantly between them.
Note also that the bore of these bearings may be purely cylindrical or tapered (conical).

5. Plummer blocks (standard bearing housing) have been developed so that bearings can be rigidly, properly contained and attached to welded frames with minimal machining preparation.
A typical housing is shown in side section view at left and in front view above.
By choosing spacers to fit on either or both sides of the bearing, the clearances at the sides of the bearings can be removed and the housing can be made to take axial loads.

6. Bearing can be mounted inside particular gear boxes, engines or other specific machines, or may be fixed to structures like welded frames using mass produced housings. The plummer block is one example of off-the-shelf housing, above are shown 2 other types of catalogued housings. Note that both have some clearance on either side of the typical bearing.
Note that the bearings shown here have tapered split sleeves clamping their bore to the parallel sided shafts. The clamping force must not be so large as to cause interference between the rolling elements and the tracks.

7. Selection of bearings according to dynamic loads and expected life:
This the number of millions of revolutions that is required from the bearing
This is the Equivalent Dynamic Load that the bearing carries which is calculated using the radial and axial components of the actual load.
The equivalent load is calculated from the combination of radial and axial loads that the particular application requires.
The linear coefficients X & Y vary with the bearing type and the proportion of the radial to axial loads.
The life of a bearing in a particular application may then be calculated from this exponential function. The ratio is of the Basic Load rating ( C - provided for each bearing) and the Equivalent Load that the bearing will be subjected to.
p = 3 for ball or for roller bearings
For each bearing there a minimum load that is required to ensure that the rolling elements roll and do not slide. Hence one cannot be assured of very long life by just reducing the load or picking a bigger bearing. Similar calculations can be done for static loads. Corrections can be made for fluctuating loads.

8. In most assemblies it is most important not to ‘over-constrain’ a shaft (ie not to have more than one bearing doing the same task:
The bearing at left restricts axial and radial movement of this motor’s rotor, the bearing at right (the output end of the motor) takes radial loads only and permits axial movement. Some axial movement is necessary for differential thermal expansion of the assembly and variations in manufacturing tolerances. Typically it would be wrong for axial thrust to be taken at both ends of the shaft, because almost certainly the result would be that the bearings would fight or load each other.

9. A gear wheel that takes both axial and radial loads, is held in place by self aligning bearings. Note that these bearings allow considerable angular misalignments between the centre lines of the two bearings, within the housing or frame, on which the gear wheel is mounted. Note also that the RH bearing locates the shaft axially.

10. B A A B F F
With almost no exceptions bearings are designed to take axial and radial loads only. There is almost no bearing that is designed to take a moment about an axis perpendicular to the centre line of its shaft. The wheels above may transmit a moment to the shaft (by force F) but only by transmitting two transverse forces (A & B), separated by some distance, to the shaft.

11. Development of wheel bearings that can cope with radial and moment loads, from the 60s and 80s

12. A fork lift drive motor, gear reduction, steering and wheel bearings in one compact assembly.
Note that the steering bearings are preloaded against each other. This is done to ensure that the balls never come loose and permit impact loads between the balls and the tracks

13. To ensure that even in rigid installations as exemplified by the above drawing, the alignment of bearings should not ‘fight’ with each other. For example the double row spherical roller bearing should not interfere with the alignment of the spherical thrust roller bearing at the bottom of the shaft. This can be achieved if the two bearing’s outer track spherical radii share a common centre.

14. A ‘Cooper’ bearing that splits horizontally, along the CL of the shaft
A ‘Cooper’ bearing that splits horizontally, along the CL of the shaft. This allows the bearing to be serviced or replaced without removing the shaft

15. There are exceptions, against the use of bearings expecting near perfect alignment and almost no shaft deflection, if the rigidity of the shaft is such that non aligning bearings can safely share the same centre lines.

16. There is also an exception to bearings not being made to accept moments. There is a range of very deep grove ball bearings which can cope with a relatively small moment. These are especially made for pulley sheaves. Note that for the larger sheave the moment is taken by two parallel bearings.

17. For slow moving contact velocities bearing manufacturers typically make a range of plain slide bushings that range from using steel on steel, for very high contact loads, to steel on bronze for lesser loads.
Spherical cup bearings are shown at left but cylindrical and other designs are available.