1. Electrical Current – flow of electrons
Complete the Circuit
Electrical Current – flow of electrons
YOU CONDUCT ELECTRICITY!
Sunday July 13, 2014
Mission: JiggyBot

2. JiggyBots are electrical devices that light up and vibrate.
The JiggyBot Mission
Mission: To build a JiggyBot that will win a race
JiggyBots are electrical devices that light up and vibrate.
Mission Targets:
I can identify and describe the function of the components used to light up and move the JiggyBot.
I can read and interpret an electronic circuit diagram (schematic).
I can describe the flow of electrical current through the JiggyBot components to explain how it works.
I can solder the components of the JiggyBot onto a printed circuit board (PCB) successfully to light up the light-emitting diode (LED) and vibrate.
Sunday July 13, 2014
Mission: JiggyBot

3. JiggyBot Baggie Components
Mission: JiggyBot
JiggyBot Baggie Components
Directions: Find this page in your lab manual
Open the JiggyBot baggie and get out the electronic components.
Match the components with the correct component name on the JiggyBot Component Inventory Sheet.
Use the internet or reference sheet to determine the function of each component in the kit and record in the space provided.
Sunday July 13, 2014
Mission: JiggyBot

4. Mission: JiggyBot Printed Circuit Board
Mechanically supports and Electrically connects electronic components using electrically conductive tracts etched from copper sheets and laminated on a non conductive substrate.
Note: Electrically conductive means that electricity can flow through the tracts and the into the components.
Sunday July 13, 2014
Mission: JiggyBot

5. Mission: JiggyBot Battery
Device that converts chemical energy into electrical energy.
Switch Device used to open and close an electrical circuit. Resistor Limits (resists) the flow of electrical current
Sunday July 13, 2014
Mission: JiggyBot

6. LED Light Emitting Diode
Diodes are polarized devices. Electricity can only flow in one direction through them.
Click here to learn more 
Sunday July 13, 2014
Mission: JiggyBot

7. The Motor Unbalanced load = vibration Click to find out more 
Sunday July 13, 2014
Mission: JiggyBot

8. Breadboarding
Sunday July 13, 2014
Mission: JiggyBot

9. Challenge
Use the breadboard in your JiggyBot baggie to practice creating a circuit that will light the LED.
Draw the connections that worked on your worksheet by using the schematic symbols for the battery, LED and resistor.
When you get it working – take a picture of it!!
Sunday July 13, 2014
Mission: JiggyBot

10. Build a Resistor-LED circuit
Challenge
Build a Resistor-LED circuit
Schematic
PREDICT: Why do you think it is necessary to use a resistor with the LED?
Sunday July 13, 2014
Mission: JiggyBot

11. JiggyBot Altium
Sunday July 13, 2014
Mission: JiggyBot

12. JiggyBot Schematic
Sunday July 13, 2014
Mission: JiggyBot

13. * Breadboard your JiggyBot components*
Next Challenge
* Breadboard your JiggyBot components*
Sunday July 13, 2014
Mission: JiggyBot

14. Now it’s time to learn to solder!
Sunday July 13, 2014
Mission: JiggyBot

15. Soldering Establishes physical and electrical connections Used by
Electricians
Electronics technicians
Electrical engineers
Jewelry makers
Stained glass manufacturers
Sunday July 13, 2014
Mission: JiggyBot

16. Solder
is a fusible metal alloy used to join together metal work pieces and having a melting point below that of the work piece. Composed primarily of Lead and Tin. (so we need to wash our hands when we’re finished) Take a piece and bend or stretch it – it’s ductile!
Sunday July 13, 2014
Mission: JiggyBot

17. Soldering 101 Soldering is dangerous if not respected.
Be mindful of where you are and where the soldering iron is around you.
If you get burned…LET US KNOW IMMEDIATELY!
Stay together, don’t work ahead for now (For your safety)
Sunday July 13, 2014
Mission: JiggyBot

18. PCB – Printed Circuit Board
Sunday July 13, 2014
Mission: JiggyBot

19. PCB – Printed Circuit Board
Soldering Pads
Top View
Side View
Circuit Board
Component
Sunday July 13, 2014
Mission: JiggyBot

20. Get your station Ready
Moisten your sponges with the water bottles at your tables. (You don’t need standing water)
Turn your soldering irons to 750° F.
Would like to have a picture of our soldering iron on 750
Sunday July 13, 2014
Mission: JiggyBot

21. Preparing your Iron
Tin the tip of the soldering iron by melting an inch or so of solder on the tip.
The iron will now look shiny on the tip.
Then wipe any excess solder on the golden sponge.
Now place the iron back into the holder.
Tinning your soldering iron in this manner will aid in future soldering.
Sunday July 13, 2014
Mission: JiggyBot

22. Close up
Sunday July 13, 2014
Mission: JiggyBot

23. Strategy
Soldering
Iron
Sunday July 13, 2014
Mission: JiggyBot

24. Move soldering iron until tip is touching wire & solder pad
Strategy
Move soldering iron until tip is
touching wire & solder pad
Sunday July 13, 2014
Mission: JiggyBot

25. Move solder to touch edge of tip
Strategy
Move solder to touch edge of tip
Solder
Sunday July 13, 2014
Mission: JiggyBot

26. Hold until solder melts
Strategy
Hold until solder melts
on tip by wire
Solder
Sunday July 13, 2014
Mission: JiggyBot

27. Move soldering iron tip up. This will drag solder up with it.
Strategy
Move soldering iron tip up. This
will drag solder up with it.
Solder
Sunday July 13, 2014
Mission: JiggyBot

28. Look for shinny fillets
Strategy
Look for shinny fillets
Sunday July 13, 2014
Mission: JiggyBot

29. Soldering Tips Make sure the tip is hot! Clean & tin the tip regularly
Keep tip clean by using wet sponge and scour pad
Heat all parts until they are hot enough to melt solder
Hold the iron on the joint until the solder flashes around the pad
Do not use too much solder (Less is more here)
Sunday July 13, 2014
Mission: JiggyBot

30. Tips
Use caution when clipping leads to avoid flinging metal across the room.
All soldering must achieve a good solder filet on the pad as shown for circuit reliability.
Bend resistors and diodes using needlenose pliers as shown.
Sunday July 13, 2014
Mission: JiggyBot

31. Solder Joints
Sunday July 13, 2014
Mission: JiggyBot

32. The tear drop of Joy
Sunday July 13, 2014
Mission: JiggyBot

33. Congratulations you just soldered your first component at
Time to tweet, instagram, or facebook!
Sunday July 13, 2014
Mission: JiggyBot

34. JiggyBot Altium
Sunday July 13, 2014
Mission: JiggyBot

35. JiggyBot Schematic
Sunday July 13, 2014
Mission: JiggyBot

36. Be certain to insert the short (negative) lead into the square.
JiggyBot - Step 1
Insert the LED into D1, solder then clip leads.
Be certain to insert the short (negative) lead into the square.
Sunday July 13, 2014
Mission: JiggyBot

37. Steps 2 - 4 Insert, solder and clip leads R1 Sw M1
Sunday July 13, 2014
Mission: JiggyBot

38. Facebook, Tweet, Instagram, Vine,
Step 5
If your JiggyBot vibrates and the LED is on, then you have successfully built (soldered) your first electronic device!
Facebook, Tweet, Instagram, Vine,
Whatever YOU do – tell the world how awesome you are 
Sunday July 13, 2014
Mission: JiggyBot

39. Prepare for Race
You may strategically solder legs (stiff wires) onto your JiggyBot.
All the JiggyBots will be placed
in a Hula Hoop and turned on.
The Hula Hoop will be removed and
Your goal is to make it to the
outer most ring (outlined in tape)
first!
Sunday July 13, 2014
Mission: JiggyBot

40. Jazz it Up Pimp out your JiggyBot – make her spectacularly fabulous!
Only one criteria:
She MUST have your picture on her.
Take lots of pictures of her and post 
Sunday July 13, 2014
Mission: JiggyBot

41. Sunday July 13, 2014
Mission: JiggyBot

42. Resistor Battery simulation
Sunday July 13, 2014
Mission: JiggyBot

43. Sunday July 13, 2014
Mission: JiggyBot