1. VERTICAL/WALL APPLICATION

2. PRIMING YOUR WALL PRIMER: MAY BE APPLIED DIRECTLY OVER DRYWALL, MASONRY, CONCRETE, CONCRETE BLOCK, OR ICF/STYROFOAM SUBSTRATES MAY BE APPLIED DIRECTLY OVER DRYWALL, MASONRY, CONCRETE, CONCRETE BLOCK, OR ICF/STYROFOAM SUBSTRATES

3. SCRATCH COAT CONCRETE, CONCRETE BLOCK, AND OTHER WALLS MAY BE WIRED TO ACCEPT THE APPLICATIONCONCRETE, CONCRETE BLOCK, AND OTHER WALLS MAY BE WIRED TO ACCEPT THE APPLICATION APPLY SCRATCH COAT TO SMOOTH OUT THE WALL, THEN BRUSH ROUGHAPPLY SCRATCH COAT TO SMOOTH OUT THE WALL, THEN BRUSH ROUGH CURE SCRATCH COAT FOR 24 HOURS MINIMUMCURE SCRATCH COAT FOR 24 HOURS MINIMUM

4. SCRATCH COAT: RECOMMENDED MIX SCRATCH COAT: WALL MIX WALL MIX AVAILABLE IN WHITE OR GRAY AVAILABLE IN WHITE OR GRAY 50 POUNDS COVERS UP TO 56 SQUARE FEET AT 1/8” THICK 50 POUNDS COVERS UP TO 56 SQUARE FEET AT 1/8” THICK ALLOW TO DRY COMPLETELY BEFORE NEXT STEP ALLOW TO DRY COMPLETELY BEFORE NEXT STEP

5. STENCIL BROWN COAT: RE-APPLY PRIMER WITH PUMP SPRAYER RE-APPLY PRIMER WITH PUMP SPRAYER USE THE SAME WALL MIX USE THE SAME WALL MIX WHILE BROWN COAT IS STILL TACKY ADHERE YOUR STENCIL TO THE BROWN COAT BY LIGHTLY TROWELINGWHILE BROWN COAT IS STILL TACKY ADHERE YOUR STENCIL TO THE BROWN COAT BY LIGHTLY TROWELING ALLOW BROWN COAT TO SET SLIGHTLY (NO LONGER SOFT)ALLOW BROWN COAT TO SET SLIGHTLY (NO LONGER SOFT)

6. COLOR COAT/TOP COAT COLORPAX DRY PIGMENT DRY PIGMENT PRE-MEASURED PRE-MEASURED MIXES DIRECTLY INTO WALL MIX MIXES DIRECTLY INTO WALL MIX LIQUID COLOR LIQUID PIGMENTLIQUID PIGMENT MIXES DIRECTLY INTO WALL MIXMIXES DIRECTLY INTO WALL MIX

7. APPLYING COLOR COAT APPLY THE TOP COAT USING WALL MIX MIXED WITH THE DESIRED COLORANTS (LIQUID COLOR OR COLORPAX)APPLY THE TOP COAT USING WALL MIX MIXED WITH THE DESIRED COLORANTS (LIQUID COLOR OR COLORPAX) TROWEL OR SPRAY COLOR COAT THINLY OVER THE SURFACETROWEL OR SPRAY COLOR COAT THINLY OVER THE SURFACE OUTLINE OF STENCIL SHOULD BE VISIBLE THROUGH THE FINISH COATOUTLINE OF STENCIL SHOULD BE VISIBLE THROUGH THE FINISH COAT

8. TEXTURING RELEASE AGENT IS APPLIED AND THE SURFACE TEXTUREDRELEASE AGENT IS APPLIED AND THE SURFACE TEXTURED CLEAR LIQUID RELEASE OR COLORED POWDER RELEASE MAY BE USEDCLEAR LIQUID RELEASE OR COLORED POWDER RELEASE MAY BE USED DO NOT ALLOW THE RELEASE AGENT TO GET ON THE BASE COATDO NOT ALLOW THE RELEASE AGENT TO GET ON THE BASE COAT TO ALLOW TEXTURING, RELEASE MUST BE APPLIED IMMEDIATELY AFTER THE TOPCOAT, BECAUSE IT SETS UP QUICKLYTO ALLOW TEXTURING, RELEASE MUST BE APPLIED IMMEDIATELY AFTER THE TOPCOAT, BECAUSE IT SETS UP QUICKLY

9. PULLING YOUR STENCIL REMOVE STENCIL AS SOON AS THE OVERLAY CHIPS FREELY FROM THE STENCIL (SAME-DAY)REMOVE STENCIL AS SOON AS THE OVERLAY CHIPS FREELY FROM THE STENCIL (SAME-DAY) USE A WIRE BRUSH TO DETAIL JOINTSUSE A WIRE BRUSH TO DETAIL JOINTS DO NOT LEAVE STENCIL IN OVERNIGHTDO NOT LEAVE STENCIL IN OVERNIGHT ALLOW TO CURE FOR 24 HOURS BEFORE CLEANING YOUR SURFACEALLOW TO CURE FOR 24 HOURS BEFORE CLEANING YOUR SURFACE

10. CONTINUE WITH THE SAME STEPS AS FOR CAST-IN-PLACE — WITH THE EXCEPTION OF SEALINGCONTINUE WITH THE SAME STEPS AS FOR CAST-IN-PLACE — WITH THE EXCEPTION OF SEALING IT IS CRITICAL TO SEAL ACCORDING TO THE OVERLAY MANUFACTURER’S SPECIFICATIONSIT IS CRITICAL TO SEAL ACCORDING TO THE OVERLAY MANUFACTURER’S SPECIFICATIONS CLEAN & SEAL