1. CHE/ME 109 Heat Transfer in Electronics LECTURE 5 – GENERAL HEAT CONDUCTION EQUATION

2. PRIMARY THREE DIMENSIONAL HEAT TRANSFER MODELS  DEVELOPED AS PARTIAL DIFFERENTIAL EQUATIONS, IN RECTANGULAR COORDINATES, OF THE FORM:

3. FORMS FOR SPECIFIC CONDITIONS  FOR UNIFORM k, THE POISSON EQUATION (STEADY-STATE) APPLIES (EQN. 2-40):

4. FORMS FOR SPECIFIC CONDITIONS  THE DIFFUSION EQUATION APPLIES FOR TRANSIENT HEAT TRANSFER WITH NO GENERATION (EQN. 2-41):

5. FORMS FOR SPECIFIC CONDITIONS  THE LAPLACE EQUATION APPLIES FOR STEADY-STATE WITH NO GENERATION: (EQN. 2-42)

6. FORMS FOR SPECIFIC CONDITIONS  SIMILAR EQUATIONS ARE DEVELOPED FOR CYLINDRICAL AND SPHERICAL COORDINATE SYSTEMS  CYLINDRICAL (EQN. 2-43) .SPHERICAL (EQN. 2-44)

7. SOLUTIONS TO DIFFERENTIAL EQUATIONS  EMPLOY EITHER BOUNDARY AND/OR INITIAL CONDITIONS  BOUNDARY CONDITIONS ARE TYPICALLY SPECIFIED AT AN INTERFACE IN THE SYSTEM  TWO BOUNDARY CONDITIONS MUST BE SPECIFIED IN EACH DIRECTION OF HEAT TRANSFER

8. SOLUTIONS TO DIFFERENTIAL EQUATIONS 

9. BOUNDARY CONDITIONS  TYPICALLY TAKE THE FORM OF FIXED TEMPERATURES AT INTERFACES  EXAMPLE - IF THE TEMPERATURES ARE SPECIFIED AT THE BOUNDARIES OF A LARGE THIN PLATE, CALCULATE THE TEMPERATURE GRADIENT AND HEAT FLUX THROUGH THE PLATE  FOR MULTIDIMENSIONAL SYSTEMS, THE ANALYTICAL SOLUTIONS ARE MAY TAKE THE FORM OF EIGENFUNCTIONS AND NUMERICAL SOLUTIONS MAY BE USED

10. SPECIFIED HEAT FLUX  HEAT FLUX BOUNDARIES  CONDUCTION TO CONDUCTION (SERIES OF SOLIDS)  AT THE INTERFACE BETWEEN THE TWO SOLIDS, THE EQUALITY OF HEAT FLUX REQUIRES:  THE TEMPERATURES WILL BE EQUIVALENT, BUT THE TEMPERATURE GRADIENTS WILL DEPEND ON THE RELATIVE VALUES OF k.

11. EXAMPLE  A CHIP CARRIER IS BONDED TO A LEAD FRAME USING A CONDUCTIVE ADHESIVE. FOR SPECIFIED TEMPERATURES AT THE SURFACE OF THE CHIP AND THE PINS OF THE LEADFRAME, CONSIDERING ONLY CONDUCTION, DETERMINE THE TEMPERATURE AT THE INTERFACE BETWEEN THE BONDING LAYER AND THE LEADFRAME SURFACE.

12. CONVECTION TO CONDUCTION FLUID TO SOLID  AT THE CONVECTION/CONDUCTION INTERFACE, EQUALITY OF HEAT FLUX REQUIRES THAT THE CONVECTED HEAT EQUAL THE CONDUCTED HEAT  THE TEMPERATURES WILL BE THE SAME AT THE INTERFACE AND THE FLUX WILL DEPEND ON THE RESISTANCE THROUGH THE TWO MEDIA  EXAMPLE - CONVECTION COOLING FOR A HEAT GENERATING DEVICE. FOR A SPECIFIED MAXIMUM TEMPERATURE AT THE INTERFACE AT A CONSTANT FLUX, DETERMINE THE NECESSARY BULK TEMPERATURE FOR THE COOLING FLUID FOR A SPECIFIED VALUE OF h

13. RADIATION TO CONDUCTION  RADIATION SOURCE TO SOLID  AT THE RADIATION/CONDUCTION INTERFACE, CONSTANT FLUX REQUIRES:  THE TEMPERATURE IS CONSTANT AND THE HEAT FLUX DEPENDS ON THE RADIATIVE AND CONDUCTIVE PROPERTIES OF THE MEDIA

14. RADIATION TO CONDUCTION  EXAMPLE - A HEAT GENERATING DEVICE HAS A SPECIFIED SURFACE TEMPERATURE. DETERMINE THE QUANTITY OF HEAT THAT IS DISSIPATED BY RADIATION IF THE TEMPERATURE OF THE SURROUNDINGS ARE AT A SPECIFIED VALUE FOR A MATERIAL WITH A SPECIFIED EMISSIVITY

15. HEAT FLUX BOUNDARY CONDITIONS  FOURIER’S LAW APPLIES FOR A SPECIFIED HEAT FLUX IN ONE DIRECTION  INSULATED SURFACE - IDEAL SYSTEM WITH NO HEAT TRANSFER IN A SPECIFIED DIRECTION

16. SPECIFIED TEMPERATURE GRADIENTS  FOR STEADY STATE PROCESSES  THE FLUX THROUGH A MEDIA IS MODELED BASED ON THE TEMPERATURES THAT BOUND IT  FOR CONDUCTION (EQN. 2-46)  SIMILAR EQUATIONS CAN BE DEVELOPED FOR AN OVERALL ΔT FOR CONVECTION OR RADIATION

17. COMBINED MECHANISMS  FOR SOME SYSTEMS THERE MAY BE PARALLEL HEAT TRANSFER THROUGH THE SAME OR DIFFERENT MECHANISMS  HEAT MAY BE TRANSFERRED FROM A HEAT GENERATING UNIT BY  CONDUCTION - WHERE IT IS CONNECTED TO A SOLID HEAT SINK  CONVECTION - WHEN FLUID IS USED TO CONVECT AWAY HEAR  RADIATION - WHEN OTHER OPAQUE MEDIA AT DIFFERENT TEMPERATURES ARE ON A LINE OF SIGHT WITH THE HEAT TRANSFER SURFACE

18. INITIAL CONDITIONS  INITIAL TEMPERATURE VALUES ARE SPECIFIED AT ALL POINTS IN THE SYSTEM AT TIME ZERO  THE SOLUTION REQUIRES SPECIFICATION OF INITIAL TEMPERATURES AT ALL LOCATIONS IN THE SYSTEM AT TIMES > ZERO.  FOR EXAMPLE - A MOTHERBOARD IS INITIALLY UNIFORMLY AT AMBIENT TEMPERATURE, PRIOR TO INITIATING POWER. DETERMINE THE TEMPERATURES AT LOCATIONS ON THE MOTHERBOARD DURING OPERATION.  THIS TYPE OF PROBLEM WOULD NEED TO HAVE BOUNDARY CONDITIONS SPECIFIED AT TIME t > 0 TO DEVELOP A TRANSIENT SOLUTION.