1. NAT64 marcelo bagnulo, Philip Matthews, Iljitsch van Beijnum IETF 72 - Dublin

2. Application scenario IPv6 Only host IPv6 Only host IPv4 Only Host IPv4 Only Host NAT64 -Communications initiated by the v6-only host -Compatible with ICE -No support for communications initiated by the v4 only side without previous action from the v6 side (i.e. No support for v6 only servers, beyond the creation of static mappings) -No changes required in any host for basic functionality -Supports communications initiated using the FQDN (of the v4 node) using DNS64

3. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR for FQDN(H4) ?

4. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR for FQDN(H4) ?

5. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR for FQDN(H4) ? enpty

6. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR for FQDN(H4) ? A RR for FQDN(H4) ?

7. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR for FQDN(H4) ? A RR for FQDN(H4) ? IP4

8. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT Synthetizes AAAA RR as Pref::/96+IPv4

9. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR Pref:IP4

10. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT Src: IP6,s Dest: Pref:IP4,d Src: IP6,s Dest: Pref:IP4,d

11. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT IP6,s T,t

12. Overview NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT Src: T,t Dest: IP4,d Src: T,t Dest: IP4,d

13. Comparison with NATPT (RFC2766) NAT64 only supports v6 initiated communications – NATPT supports both v4 and v6 initiated, requiring a set of cumbersome techniques NAT64 and DNS64 are completelly decoupled – No relation between the NAT64 state and the synthetic RR – DNS64 preserves DNS semantics, DNS responses are valid irrespectivly of the path used by data packets NAT64 allows to preffer native connectivity over translated connectivity NAT64 is compatible with DNSSec NAT64 supports some modes of IPSec NAT64 is fully specified, compatible with behave requirements

14. A couple of design questions

15. What prefix to use to map v4 addresses in v6 land? Option 1: Local prefix – We use a prefix /96 obtained from the site’s block – Differnet prefixes for different nat64 boxes in the same site Option 2: global prefix – Candidates: V4mapped prefix V4compatible prefix A new global prefix assigned by IANA

16. Implication 1: global translated addresses If we use a global prefix, we have a globally unique RR that represent translated addresses Less problems with DNS, DNSSec No need to configure the local prefix in DNS64

17. Implication 2: communication with dual stack Local Prefix: Translated addresses are represented as one of the site’s address – Need other means to distinguish them: EDNS0 option Only upgraded dual stack can use it: apps that break with nats may break NAT64 v6 v4 DNS64 DNS H6 IP6 H4 IP4 IPT AAAA RR Pref:IP4 EDNS0

18. Implication 2: Communications with dual stack Global prefix: – V4mapped prefix: Automatically less preferred due to rfc3484 policy Windows vista, Macos, Linux, don’t use it on the wire – V4 compatible prefix Automatcially less preferred compared to native v6, but more preferred than v4 (represented as v4 mapped) Windows vista, macos, linux send packets to this prefix – Other global prefix from IANA More rpeferred than v4 Longest prefix match rule in rfc3484 could help (if not deprecated)

19. Implication 3: routing fluctuations Failure in intra site routing fluctuations NAT64_1 v6 v4 DNS64 DNS H6 IP6 H4 IP4 NAT64_2

20. Implication 3: routing fluctuations Failure in intra site routing fluctuations NAT64_1 v6 v4 DNS64 DNS H6 IP6 H4 IP4 NAT64_2

21. Implication 3: routing fluctuations Failure in intra site routing fluctuations NAT64_1 v6 v4 DNS64 DNS H6 IP6 H4 IP4 NAT64_2

22. Endpoint independence vs. Higher utilization of v4 addresses Endpoint independence requires mappings are: (srcIP6,srcp) (T,t) Address and port dependent mapping are: (srcIP6,srcp,dstIP6,dstp) (T,t,dstIP4,dstp’) Can we afford endpoint independence in v6?