1. Basic Electrical Systems Theory and Repair
Chapter 29
Page 387

2. So, Where is Electronics in a Car
Everywhere
Antilock brakes, engines, emissions, dash, fuels system, transmissions, tires, suspension, windows, safety systems, lighting.
----Well, I could go on and on and on.

3. The Basics

4. Atoms
Positive
Negative

5. Conductors and Insulators

6. Conductors Conductors
A good conductor must not have more than four electrons in the outer valence ring of an atom. Copper is one of the best conductors; along with aluminum and gold, conductors have one electron in the outer valence ring.

7. Insulators Insulators
A good insulator must have more than four electrons in the outer valence ring of an atom. Rubber, glass, and porcelain are the best insulators with many electrons in the outer valence ring.

8. Electrical Flow

9. Electron Movement This is the way it really is!
Negative to Positive
This is what we are taught!
Positive to Negative

10. Wiring is coated with PVC, a flexible plastic to insulate the copper wiring.
Color Chart

11. Circuit Requirements = A full circle is provided
Switch
12 v
Complete path
Load
(light) +
Source
(Battery) _
Source – Battery or voltage supply
Load – Electrical components, lights, radio, etc.
Complete path for electron flow – Wires and connections

12. Circuit Devices Controls Devices Protection Devices
Switches for on and off
Fuses and Circuit Breakers
Protect form Overloads

13. Fuses and Circuit Breakers

14. Other Symbols

15. Electrical Terms
Voltage- Also called Electromotive Force, Pressure of electricity or the amount of force it takes to move electrons. Measured in volts.
Current- The movement or flow of electrons, measured in amperes or amps for short.
Resistance-Anything that impedes or slows the flow of electrons. Measured in ohms.

16. More Electrical Terms
AC – Alternating Current (shop lights and equipment)
DC – Direct Current (Auto battery and most systems)
Auto voltage used is normally between 12 and 15 volts

17. Circuit Types
Series
Parallel
Combination

18. Series Circuit

19. Series Circuits
Series circuits provide only one path for electron flow through a circuit.
When one component fails, the remaining components quit working.
Light
12 v
Light
Light

20. Parallel Circuit

21. Parallel Circuits
Parallel circuits provide two or more paths for electron flow through a circuit.
When one component fails, the remaining components are not affected.
12 v
Lights

22. Combination
The simplest type is to use a switch in the first part of the circuit (series) and the rest of the circuit is wired in parallel.
Lights
12 v

23. Ohm’s Law Greg Simon Ohm (1787 – 1854)
Ohm’s Law: It takes one volt to push one ampere of current through one ohm of resistance.
*Look at page 394 for more.

24. E I R Ohm’s Law E = Voltage (Electromotive Force)
I = Current (Intensity)
R = Resistance (Ohms)
E = IR
I = E/R
R = E\I

25. E I R Ohm’s Law E = IR I = E / R R = E \ I E = IR 12 = 3 X 4 I = E / R
3 amps
12 volts
I = E / R
3 = 12 / 4
R = E / I
4 = 12 / 3

26. Magnetism Laws of magnetism: 1. Like poles repel each other.
2. Unlike poles attract each other.
3. The attractive force increases as the distance between the magnets decreases. N S N S S N

27. Magnetic Fields

28. Magnetism Magnetic Field-
Occurs when a current is flowing through a conductor.
Electromagnets-
Artificially creating a magnetic field. A coil of wire with a voltage applied.

29. Electromagnets M
Switch
Battery
Starter
Solenoid or Relay

30. Electromagnets

31. Resistors

32. A Few More Terms
Semiconductors- Can act as both insulator and conductor.
Diode- an electronic one way check valve, it allows flow one way but doesn’t allow it to reverse the other way.
Transistor- electronic relay. Its very fast, and no moving parts.

33. Basic Tests Meters Analog and Digital Digital Volt-ohm Meter (DVOM)
or Digital Multimeter (DMM)

34. Measurements

35. Voltage Testing

36. Voltage Check

37. Testing Voltage After Switch
Open = wire broke or fried wire

38. Circuit Test 3
1 = 12 v
2 = 12v
3 = 12v 1 2 2

39. Continuity Testing

40. Ohmmeter Test

41. Diode Check
Diode is a one way street only. Reversing the multimeter leads will tell us if the voltage is allows one way and is stopped the opposite way. If it doesn’t do this toss the diode.
.000 one way and 1. the other.

42. Testing Device with Ohmmeter with Power Removed
Continuity Should be .000 if Good
Infinity Should be 1. if Bad

43. Testing Amps
Need to change red probe lead to Amp on meter

44. Test Light

45. Test Light

46. Using a Jumper Wire
Bypassing Ground

47. Bypass a Switch with Jumper Wires

48. Circuit Defects
Open
Incomplete or broken circuit. The circuits quits working.
Short
Two wires unintentionally connecting with each other. Could cause more than one component to operate.

49. Circuit Defects Ground
When a positive and negative wire contact each other. Could cause sparking and extreme heat due to high current flow. Very low resistance blows fuses, circuit breakers, or fusible links.

50. Circuit Defects
Open Circuits

51. Circuit Defects
Short Circuits

52. Circuit Defects
Ground Circuits

53. Your Job.
Complete chapter Questions 1-15 (review) and 1-10 (ASE-style). Page
Write on a separate paper and write out the complete question and your answer. ( do not write the other answer options).
Complete the chapter worksheet (I will give it out). You may write on it.
File all items in your note book.
Notebooks will be graded in the future.