1. Audio-Visual Solutions HDMI Installation Training Analog to Digital, simple to sophisticated, all from one source!

2. Who is Intelix? Founded in 1986 Based in Middleton, WI USA Engineering heritage Historically Pro-Audio Today 90% Video

3. Who is Intelix? Market Segments Pro AV Residential CI DataCom Security-CCTV

4. Product Categories HDMI Systems Digital Signage Systems Passive and Active Twisted Pair Extension Solutions Security Distribution Products Audio Matrix Systems Room Combine Systems Paging Systems Who is Intelix?

5. Before we start… The most current Installation Manuals and Software are located at: www.intelix.comwww.intelix.com under “Technical Library” HDMI Product Installation

6. Installing the DIGI-HD-UHR2 and DIGI-HD-IR2 HDMI Product Installation

7. Installation Considerations Installing the UTP Extenders Use the EIA/TIA 568B Crimp Pattern Power is required on send and receive extenders Third-party IR systems are not compatible with the DIGI-HD-IR2 (Intelix is a 5V system) The extenders will feel warm (98 degrees F) Do not connect the balun to a telecommunication outlet wired to unrelated equipment. Ensure all connected twisted pair cabling is straight-through (point-to-point)

8. Instructions Power off all AV equipment Make sure you have a point-to-point circuit. Make sure source and display work with HDMI cable Test the HDMI patch cables Installing the UTP Extenders

9. Instructions Connect the DIGI-HD-UHR2 transmitter to the source then the receiver to the display (no power) Connect the CAT cable Installing the UTP Extenders

10. Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality Installing the UTP Extenders

11. Copying EDID - DIGI-HD-UHR2 Disconnect the transmitter and receiver Connect transmitter to display with HDMI cable Installing the UTP Extenders

12. Copying EDID - DIGI-HD-UHR2 Press “Hand Shake” button LEDs will flash and then remain solid EDID is copied Disconnect transmitter and repeat normal installation Installing the UTP Extenders

13. Bandwidth Shaping DIGI-HR-UHR2 Position 1Position 2Mode Off Use copied EDID data from display OffOnTurn on Dolby TrueHD and DTS-HD OnOffTurn on stereo audio On No function Installing the UTP Extenders Transmitter DIP Switch Positions Unplug all of the cables to make DIP switch changes Change the DIP switch position Reconnect the transmitter The UHR2 will not pass EDID information from the display to the source

14. Bandwidth Shaping DIGI-HR-IR2 Position 1Position 2Mode Off Read EDID data from displays OffOnTurn on Dolby TrueHD and DTS-HD OnOffTurn on stereo audio On No function Installing the UTP Extenders Transmitter DIP Switch Positions Unplug all of the cables to make DIP switch changes Change the DIP switch position Reconnect the transmitter The IR2 will pass EDID information from the display to the source.

15. Using IR with the DIGI-HD-IR2 Disconnect power from Baluns Attach emitter to source and eye to display Plug the emitter into send side of DIGI-HD-IR2 Plug the eye into the receive side of DIGI-HD-IR2 Installing the UTP Extenders

16. Using IR with the DIGI-HD-IR2 Power the extenders and test IR Installing the UTP Extenders

17. Installing the DIGI-HD-COAX-S and the DIGI-HD-COAX-R HDMI Product Installation

18. Installation Considerations Will only run at 3 resolutions 720p-60 1080i-30 1080p-60 DVI will only work at the available resolutions Source equipment will need to be forced into available resolutions No taps, splitters, amps, pads or filters Works with barrels or F-connectors Needs a minimum of 50’ of 75 Ohm cable Does not pass 3D Installing the DIGI-COAX

19. Instructions Power off all AV equipment Make sure you have a point-to-point circuit. No taps, splitters, amps, pads or filters Works with barrels or f-connectors Installing the DIGI-COAX

20. Instructions Connect the transmitter to the source then the receiver to the display (no power) Connect the COAX cable to the “A” side of the transmitter (BNC or F-connector) Connect the Coax to the “input” on the receiver Installing the DIGI-COAX

21. Instructions Power on the receiver then transmitter Power on the source and display devices Verify picture quality Installing the DIGI-COAX

22. HDMI Digital Signage Application Installing the DIGI-COAX

23. Installing the DIGI-SCAL-11x2 HDMI Product Installation Switcher/Format Converter/Scaler

24. DIGI-SCAL-11x2 Installing the DIGI-SCAL-11x2

25. Installation Considerations HDMI outputs are mirrored not matrixed 3 to 5 second switch time Video blue screen during switch process Volume cannot be changed It will not convert audio from digital or analog stereo to multi channel digital audio It will only convert analog stereo audio to PCM digital stereo audio and back. Installing the DIGI-SCAL-11x2

26. Installation Instructions Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-SCAL-11X2 requires one rack unit of spacing.) Installing the DIGI-SCAL-11x2

27. Installation Instructions Power off source and destination devices Connect input sources Connect output destination(s) Installing the DIGI-SCAL-11x2

28. Installation Instructions Connect power supply Connect RS232 or IR if the unit is remote controlled Power on DIGI-SCAL-11x2 Power on source and designation devices Installing the DIGI-SCAL-11x2

29. Operation – Channel Pairing Audio and Video pairing are as follows: Installing the DIGI-SCAL-11x2

30. Operation – Channel Pairing VGA Audio S-video Audio DVI-I Installing the DIGI-SCAL-11x2

31. Built-in Audio Conversion and Embedding Installing the DIGI-SCAL-11x2 Analog Stereo Audio In Analog Audio Out PCM Digital Audio Out PCM Digital Audio In PCM Digital Audio Out Analog Audio Out PCM Digital Audio Out

32. Operation – Front Control Panel Power on the unit by selecting the Standby button. Select the input with the rotary knob. Select output resolution with the Mode Selection button. Installing the DIGI-SCAL-11x2

33. Operation – Supported Signal Formats Input SignalFormat CompositePAL, NTSC S-videoPAL, NTSC YPbPr480i, 480p, 576i, 576p, 720p, 1080i, 1080p VGA800x600, 1024x768, 1152x864, 1280x768, 1280x960, 1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200 DVI-I800x600, 1024x768, 1152x864, 1280x768, 1280x960, 1280x1024, 1440x900, 1400x1050, 1600x1200, 1920x1200 HDMI480i, 480p, 576i, 576p, 720p, 1080i, 1080p Installing the DIGI-SCAL-11x2 Output SignalFormat HDMI720p, 1080p

34. Operation – Included Remote Control Installing the DIGI-SCAL-11x2

35. Operation – PC Bypass Mode PC Bypass Mode allows a computer’s native resolution to display on the destination monitor. When using PC Bypass Mode, the front panel indicators will disable. In addition, the default output will be in 1080p. PC Bypass mode will only function when a VGA or DVI signal is present and my be activated from the remote control or the “Mode Selection” button. Installing the DIGI-SCAL-11x2

36. Operation – On Screen Display Installing the DIGI-SCAL-11x2

37. Operation – RS232 Remote Control The manual has a complete list of the RS232 control codes Connect a straight-through serial cable directly to the matrix Installing the DIGI-SCAL-11x2 9600 baud rate 8 data bits 1 stop bit No parity bit No handshake

38. Installing the DIGI-HD-4X4 and 4X2 HDMI Product Installation

39. DIGI-HD-4X4 Installing the DIGI-HD-4X4

40. Installation Considerations “A” and “B” RJ45 jacks on the output will only connect to one DIGI-HD-UHR2-R or DIGI-HD-IR2-R You can mix DIGI-HD-UHR2-R or DIGI-HD-IR2-R Consider buying and extra DIGI-HD-UHR2-S to make copying EDID from the displays easier. Installing the DIGI-HD-4X4 and 4X2

41. Installation Instructions Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-4X4 requires one rack unit of spacing.) Installing the DIGI-HD-4X4

42. Installation Instructions Power off source and destination devices Connect input sources Connect output destination to HDMI or twisted pair Installing the DIGI-HD-4X4

43. Installation Instructions Recommended Twisted Pair Receivers Installing the DIGI-HD-4X4

44. Installation Instructions Installing the DIGI-HD-4X4 Twisted Pair Settings-Toggle all Ports 1.To toggle between single and dual twisted pair modes, simultaneously press and hold the Output 3 button and Key-lock button for 3 seconds. 2.Use Output 1 and Output 2 and Key-lock to toggle the DIGI-HD-4X2 3.The default setting of the DIGI-HD-4X4 is double twisted pair mode.

45. Installation Instructions Installing the DIGI-HD-4X4 Twisted Pair Settings-Using ComCtl software

46. Installation Instructions Installing the DIGI-HD-4X4 Signal Mode Settings set by DIP switches: HDshāk Inside EDID Copy Bandwidth Shaping

47. Installation Instructions Installing the DIGI-HD-4X4 DIP Switch Mode Settings

48. Installation Instructions Connect the included 12 VDC power supply to the DIGI-HD-4x4. If controlling remotely, connect RS232, Ethernet, or IR control cables. Power-on the DIGI-HD-4x4. Power-on the source and destination audio and video devices. Power off DIGI-HD-4X4 before changing the DIP switches to change signal mode. Power up to have changes take effect. Installing the DIGI-HD-4X4

49. Operation Front Panel Control Basics Installing the DIGI-HD-4X4

50. Operation Included Remote Control Installing the DIGI-HD-4X4

51. Operation - Setup IR Remote Control Installing the DIGI-HD-4X4

52. Operation - Setup RS232 and Ethernet Remote Control Installing the DIGI-HD-4X4 Web Control DHCP or Static IP address

53. Installing the DIGI-HD-8X8 HDMI Product Installation

54. DIGI-HD-8X8 Installing the DIGI-HD-8X8

55. Installation Considerations “A” and “B” RJ45 jacks on the output will only connect to one DIGI-HD-UHR2-R or DIGI-HD-IR2-R Use only DIGI-HD-UHR2-R or DIGI-HD-IR2-R for all 8 extension out puts. Do not mix. Consider buying and extra DIGI-HD-UHR2-S to make copying EDID from the displays easier. Installing the DIGI-HD-8X8

56. Installation Instructions Attach the feet or the rack ears depending on how the unit will be mounted. (The DIGI-HD-8X8 requires four rack units of spacing.) Installing the DIGI-HD-8X8

57. Installation Instructions Power off source and destination devices Connect input sources Connect output destination to HDMI or twisted pair Installing the DIGI-HD-8X8

58. Installation Instructions Recommended Twisted Pair Receivers Installing the DIGI-HD-8X8

59. Installation Instructions Installing the DIGI-HD-8X8 Signal Mode Settings set by DIP switches: HDshāk Inside Single or Dual EDID Copy Bandwidth Shaping

60. Installation Instructions Installing the DIGI-HD-8X8 DIP Switch Mode Settings

61. With DIGI-HR-UHR2-R Installing the DIGI-HD-8X8 Example setup: Inputs (3) Satellite boxes (1) DVD Player Outputs (2) Local TVs (2) Remote TVs

62. Installing the DIGI-HD-8X8 Example setup: Inputs (3) Satellite boxes (1) DVD Player Outputs (2) Local TVs (1) Remote TVs with IR remote With DIGI-HR-IR2-R

63. Installation Instructions Connect the included 12 VDC power supply to the DIGI-HD-8X8. If controlling remotely, connect RS232, Ethernet, or IR control cables. Power-on the DIGI-HD-8X8. Power-on the source and destination audio and video devices. Power off DIGI-HD-8X8 before changing the DIP switches to change signal mode. Power up to have changes take effect. Installing the DIGI-HD-8X8

64. Operation Front Panel Control Basics Installing the DIGI-HD-8X8 Default Passwords User: 1234 Admin: HDMI

65. Operation Selection using “Room View” Installing the DIGI-HD-8X8

66. Operation Selection using “Matrix View” Installing the DIGI-HD-8X8

67. Operation Select a “Preset” Installing the DIGI-HD-8X8 or

68. Operation Set a new “Preset” Installing the DIGI-HD-8X8

69. Operation – User access Lock Screen Installing the DIGI-HD-8X8 Unlock Screen

70. Operation - Setup Opening the “Utilities” menu as administrator Installing the DIGI-HD-8X8

71. Operation - Setup Set User and Admin passwords Installing the DIGI-HD-8X8 or

72. Operation - Setup Define Input Icons Installing the DIGI-HD-8X8

73. Operation - Setup Define Input Text Label Installing the DIGI-HD-8X8

74. Operation - Setup Copy EDID when using DIGI-HD-UHR2-R receivers Installing the DIGI-HD-8X8 or

75. Operation - Setup Define Output Icons Installing the DIGI-HD-8X8

76. Operation - Setup Define Output Text Label Installing the DIGI-HD-8X8

77. Operation - Setup Reset System Settings Installing the DIGI-HD-8X8

78. Operation - Setup Included Remote Control Directly with Matrix – Buttons 1 to 8 are destinations – Arrows are “previous” and “next” source Through Extender – Extender location defines output – Buttons 1 to 8 represent inputs – Discretely choose inputs Installing the DIGI-HD-8X8

79. Operation - Setup IR Remote Control Extend the IR sensor with the included “eye” -Plug it directly into the 3.5mm jack in the back of the unit -Third-party IR devices are not compatible with the 3.5mm jack Using third-party IR control -Connect from base IR control unit using Ethernet or RS232 -IR control – attached emitter to IR pickup on the front for the unit Installing the DIGI-HD-8X8

80. Operation - Setup RS232 Remote Control RS232 programming and command information is Appendix A of the manual Must receive all messages in hexadecimal number code. If messages are transmitted in decimal or ASCII codes, they will fail to work. Installing the DIGI-HD-8X8

81. Operation - Setup Ethernet Remote Control Connect an Ethernet cable directly to the matrix. The DIGI-HD-8X8 will automatically be assigned an IP address when connected to a DHCP-enabled network. By default, DHCP is enabled. Within 10 seconds of connecting the DIGI-HD-8X8 to the LAN, the yellow LED on the matrix’s Ethernet port will stop blinking and the green LED will blink intermittently. For Ethernet programming and command information, see Appendix A Installing the DIGI-HD-8X8

82. Operation - Setup Web Control Installing the DIGI-HD-8X8

83. Operation - Setup IR Twisted Pair Pass-Through Determine which devices you wish to control via the IR pass-through outputs. Connect an IR emitter to the desired IR transmit output port. Repeat for up to eight devices. All of the remote receive baluns transmit IR commands from the included remote control, thereby allowing remote control of the matrix itself. Verify that IR pass-through is enabled in the front panel LCD Utilities screen. Installing the DIGI-HD-8X8

84. Why Intelix? Maximize Performance: Complete integrated solution approach HDMI

85. Why Intelix? HDMI Insured Reliability: Multi Stage Quality Assurance Process Less than a 1% return rate

86. Why Intelix? HDMI World Class Support: Pre and post sales technical and applications support 90 day advanced replacement 2 year warranty on all products

87. Intelix Contacts Technical Sales /Training: Brad Weisbrod | bradw@intelix.com Order Status: Ellen Domine | ellend@intelix.com Pricing Inquiries: Beth Green | bethg@intelix.com Technical Support: Sterling Glass | sterlingg@intelix.com Marketing Inquiries: Eric Lang | ericl@intelix.com Domestic Sales Questions: Cameron Smith | camerons@intelix.com International Sales Questions: Steve Cohan | stevec@intelix.com 608-831-0880 phone | 608-831-1833 fax | www.intelix.com Intelix

88. Resources 608-831-0880 phone | 608-831-1833 fax | www.intelix.com Intelix Literature Library: http://www.intelix.com/tech_library/marketing_lit.aspx Product Technical Literature: http://www.intelix.com/tech_library.htm