1. Multiplexing
Break one high-speed physical communication circuit into several lower-speed logical circuits
Allows many different devices to use the circuit simultaneously while it seems that each pair of devices has the physical circuit all to itself
Usually done in multiples of 4
Two multiplexers are needed for a circuit – one to combine the original circuits into a multiplexed circuit and one to separate them back out into separate circuits
Four types of multiplexing
Frequency division multiplexing (FDM)
Time division multiplexing (TDM)
Statistical time division multiplexing (STDM)
Wavelength division multiplexing (WDM)

2. Frequency Division Multiplexing
Divides the circuit “horizontally” by assigning different frequencies (channels) to each logical circuit
All signals exist in the media at the same time on non-interfering frequencies
Available bandwidth is divided into channels and “guardbands” which separate the channels
Channels do not need to have identical capacities

3. Time Division Multiplexing
Divides the circuit “vertically” by allowing different devices to transmit on the circuit at different times
Devices take turns using the circuit to transmit data
Time is allocated to each device in turn, even if the device is idle
More efficient than Frequency Division Multiplexing, as there is no need for “guardbands”
The full capacity of the line is divided evenly among the multiplexed circuits

4. Statistical Time Division Multiplexing
Takes advantage of the fact that not all devices will be transmitting all the time
Multiplexed circuit bandwidth is typically smaller than the combined bandwidths of the individual circuits
Circuit capacity requirements are determined statistically by analyzing the usage of the circuits to be multiplexed
Given four 64kbps circuits, TDM would require a 256kbps multiplex circuit
If we find that, statistically, only two of the four circuits are typically active simultaneously, we can provision a 128kbps multiplex circuit using STDM
Provides more efficient use of bandwidth
Can cause time delay if all circuits become active simultaneously
Increased complexity and overhead, since each transmission must include an indication of the circuit it belongs to

5. Wavelength Division Multiplexing
A version of FDM used in fibre-optic cabling
Originally, fibre-optic transmission used a single “color” (light wavelength) for transmitting 622Mbps (622 million bits per second)
By attaching devices that transmit and detect different light wavelengths, multiple circuits can be multiplexed over a single fibre-optic cable
Dense Wave-Division Multiplexing (adding TDM to WDM) has increased the capacity of a single fibre-optic cable to 400 Billion bits per second
DWDM Experimental results over 1.5Tbps
1,500,000,000,000 bits per second
Approximately 200 Gigabytes/second

6. Inverse Multiplexing (IMUX)
Opposite of multiplexing
Combines two or more low-speed circuits making them appear as a single high-speed circuit
Commonly used to provide T1 circuits in Wide Area Networks
Combines 24 low-speed (64kbps) circuits to create a single Mbps circuit
IMUX equipment not standardized, so the same vendor should be used for both ends of the circuit
BONDING (Bandwidth on Demand Interoperability Networking Group) standards have been adopted by some vendors for using 6 separate ISDN links over six telephone lines for room-to-room teleconferencing

7. Digital Subscriber Line (DSL)
Provides high-speed data transmission over traditional telephone lines
Limitations on traditional phone lines is based in the telephone and switching equipment in the end offices
Actual cabling (local loop) is capable of much higher transmission capacity
Conversion from POTS to DSL involves changing end equipment, not rewiring the local loop, making it very cost effective
The customer premises equipment (CPE) includes a line splitter, which separates the traditional voice traffic from the data transmissions
The line splitter directs data transmissions into the DSL modem (also called a DSL router) which is both a modem and a Frequency Division Multiplexer
At the telephone company end office, the local loop enters into the Main Distribution Frame (MDF), which works like the line splitter on the customer premises
The MDF sends voice traffic to the voice telephone network, and sends DSL traffic to the DSL Access Multiplexer (DSLAM)
The DSLAM demultiplexes the data streams and converts them to ATM data which can be distributed to the Internet Service Provider (ISP)
The ISP’s Point of Presence (POP) can be co-located or located elsewhere

8. Asymmetric Digital Subscriber Line (ADSL)
Uses Frequency Division Multiplexing to create three separate channels over the one local loop circuit
One traditional voice circuit
One relatively high-speed simplex circuit from the end office to the customer premises
One slightly slower half-duplex circuit, primarily intended for upstream traffic from the customer premises to the end office
It is called asymmetric because each of the two data circuits have different capacities
Each of the two data channels can be further subdivided using Time Division Multiplexing
The size of the two digital channels depends on the distance from the CPE to the end office
Shorter distance to End Office results in less attenuation of the signal, allowing higher frequencies to be used and yielding a faster connection
Offering higher speed ADSL limits the number of potential customers, while offering lower speed decreases product attractiveness

9. Cable modems Digital service offered by cable companies
Data over Cable Service Interface Specification (DOCSIS) is the dominant standard
Standard most often used by cable companies running hybrid fibre coax (HFC) networks
Architecture is very similar to DSL
Main difference is that DSL is point-to-point, while cable modems share multi-point circuits
Each user must compete with other users for the available capacity
All messages on the circuit go to all computers on the circuit
Cable TV circuit enters the customer premises through a cable splitter
TV signals are sent to the TV network
Data signals are sent to the cable modem (both a modem and an FDM)
Standard coaxial cable circuit may be shared by from 300 to 1000 customers
Not all of these cable TV customers will subscribe to high-speed internet
The coax runs to a fibre node with an optical-electrical converter
Each fibre node may service up to half a dozen cable circiuts
The fibre nodes are connected to a distribution hub (also called a headend) through two separate circuits
Upstream circuit connects to a cable modem termination system (CMTS)
Downstream circuit carries both ordinary cable TV signal and downstream traffic destined for the customer premises

10. Local Area Networks Introduction LAN Components
Why use a LAN? Dedicated servers vs. Peer-to-peer LANs
LAN Components
NICs, Cables, Hubs and Network Operating Systems
Traditional Ethernet (IEEE 802.3)
Topology, Media Access Control, Ethernet Types
Switched Ethernet
Topology, Media Access Control, Performance Benefits
Wireless LANs (IEEE )
Topology, Media Access Control, Wireless Ethernet Types
Other Wireless Technologies
Infrared Wireless, Bluetooth
Improving LAN Performance
Improving Server Performance, Improving Circuit Capacity, Reducing Network Demand

11. Why use a LAN?
There are two main benefits to using a local area network: information sharing and resource sharing.
Examples of information sharing include file sharing, exchanging , and using the Internet.
Examples of resource sharing include sharing hardware and software, such as sharing an expensive printer.
Another important resource sharing technique is to purchase software on a per seat basis. For example, only purchasing a 10-seat license for a software program on a 20 client network instead of purchasing 20 copies of the same program.

12. Dedicated Server Networks
A basic LAN dichotomy exists between dedicated server LANs and peer-to-peer LANs which don’t have servers. Since 90% of all LANs have a dedicated server, this chapter mostly focuses on server-based LANs.
A dedicated server is a computer that is permanently assigned a specific server task such as being a Web server, server, file server or printer server.
Servers also run a special operating system called a server network operating system.
When many servers are part of a network, it can be referred to as a server farm.

13. Peer-to-Peer Networks
Peer-to-peer networks do not use dedicated servers.
Any computer on a peer-to-peer network can act as both a client, accessing resources or information on other computers on the network, or as a server, allowing access to attached information or resources.
Peer-to-peer networks tend to be small networks.
The main advantage of peer-to-peer networking is lower cost since there is no dedicated server, generally the most expensive network component.
The main disadvantage is that peer-to-peer networks are generally slower than dedicated server networks, since each computer is less powerful and may be in use as a client and a server at the same time.

14. Basic LAN Components The six basic LAN components are: 1. Clients
2. Servers
3. Network Interface Cards
4. Network Cables
5. Hubs and Switches
6. Network Operating System

15. Basic LAN Components

16. Network Interface Cards
Network interface cards, also called network cards and network adapters include a cable socket allowing computers to be connected to the network.
NICs are part of both the physical and data link layer and include a unique data link layer address (sometimes called a MAC address), placed in them by their manufacturer.
Before sending data onto the network, the network card also organizes data into frames and then sends them out on the network.
Notebook computers often use NICs that are plugged into the PCMCIA port.

17. Network Cables
Each computer is physically connected to the network using a cable.
These cables are either untwisted wire pairs (UTP, the most common choice), shielded twisted pair (STP), coaxial cable, or optical fiber.
Wireless LANs use radio frequencies or infrared light instead of cables.
Sometimes two different types of cabling can be linked using a special connector. A BALUN (Balanced-Unbalanced) is one such device that connects UTP and Coaxial Cable.

18. Hubs
Hubs act as junction boxes, linking cables from several computers on a network. Hubs are usually sold with 4, 8, 16 or 24 ports.
Some hubs allow connection of more than one kind of cabling, such as UTP and coax.
Hubs also repeat (reconstruct and strengthen) incoming signals. This is important since all signals become weaker with distance.
The maximum LAN segment distance for a cable can therefore be extended using hubs.

19. Network Hub

20. Network Operating Systems
The NOS is the software that runs the LAN. It comes in two types: Server NOSs & Client NOSs.
Server NOSs enable server to execute and respond to the requests sent to them as web server, print servers, file servers, etc.
Client NOS functions are typically included in most OS packages such as Windows 98 and Windows 2000.

21. Network Profiles
The network profile specifies what resources on each server are available to the network for use by other computers, including data files, printers, etc.
Devices that are not included in the network profile can not be used over the network.
User profiles describe what each user on a LAN has access to.
Most LANs also use auditing software which keeps track of which user has accessed what network resource.

22. Ethernet (IEEE 802.3) Almost all LANs today use Ethernet
Originally, Ethernet was jointly developed by a consortium of Digital Equipment Corp., Intel and Xerox and was standardized as IEEE
Ethernet LANs that use hubs are sometimes called shared Ethernet.

23. Shared Ethernet Topology
Ethernet’s logical topology is a bus topology.
This means all computers on the network receive messages from all other computers, whether the message is intended for those computers or not.
When a frame is received by a computer, the first task is to read the frame’s destination address to see if the message is meant for it or not.
Although, a decade ago most Ethernet LANs used a physical bus, almost all Ethernets today use a physical star topology, with the network’s computers linked into hubs.
It is also common to link use multiple hubs to form more complex physical topologies

24. Ethernet Topology

25. Multiple Hub Ethernet Design

26. Media Access Control
Ethernet’s medium access control protocol, called CSMA/CD, is contention-based
With a contention-based protocol, frames can be sent by two computers on the same network at the same time, in which case they will collide and become garbled.
CSMA/CD, can thus be termed “ordered chaos” because it tolerates, rather than avoids, collisions caused by two computers transmitting at the same time.

27. CSMA/CD Stands for: Carrier Sense Multiple Access w/ Collision Detect
Carrier Sense: computers listen to the network to see if another computer is transmitting before sending anything themselves.
Multiple Access: all computers have access to the network medium.
Collision Detect: if they detect a collision (CD), they then wait a random amount of time and resend the frame (It has to be random in order to avoid another collision).

28. Ethernet Physical Media Standards
Ethernet Media are formatted as follows: [Value1]Base/Broad[Value2]
Value 1: Data Rate for Medium 10 = 10Mbps
Base or Broad
Base = Baseband Mode meaning only one (digital) channel
Broad = Broadband (analog) cable transmissions use more than one channel (e.g., cable TV)
Value2: (relates to maximum distance possible in hundreds of meters or cable type T= twisted pair, F =fiber)

29. Types of Ethernet Seven types of shared Ethernet have been in use:
10Base5 = thick Ethernet, uses thick coax. This is the original Ethernet specification. Now uncommon.
10Base2 = thin Ethernet, uses thin coax. Became popular in the early 1990s as a cheaper alternative to 10Base5. Now uncommon.
10BaseT = twisted pair Ethernet, most common type of Ethernet. Uses Cat 3 and Cat 5 UTP. Common but rapidly losing ground to 100BaseT.
100BaseT = also called Fast Ethernet, has replaced 10BaseT in sales volume. Uses Cat 5 UTP (Sometimes combined 10/100 Ethernet is found in which some segments run 10BaseT and some run 100BaseT is also used by some organizations).
1000BaseT = Gigabit Ethernet. Maximum cable length is only 100 meters.
10GbE = 10 Gbps Ethernet. Uses fiber and is typically full duplex.
40GbE = 40 Gbps Ethernet. Uses fiber and is typically full duplex.

30. Types of Ethernet Name Maximum Data Rate Cables 10Base5 10 Mbps
1.       
Name
Maximum Data Rate
 Cables
10Base5
10 Mbps
Coaxial
10Base2
10BaseT
UTP cat 3, UTP cat 5
100BaseT
100 Mbps
UTP cat 5, fiber
1000BaseX
1 Gbps
UTP cat 5, UTP cat 5e,
UTP cat 6, fiber
10 GbE
10 Gbps
UTP cat 5e, UTP cat 6, UTP cat 7, fiber
40 GbE
40 Gbps
fiber
Types of Ethernet

31. Switched Ethernet Topology
Switched Ethernet uses switches instead of hubs.
While a hub broadcasts frames to all ports, the switch reads the destination address of the frame and only sends it to the corresponding port.
The effect is to turn the network into a group of point-to-point circuits and to change the logical topology of the network from a bus to a star.

32. Basic Switch Operation
Switches make forwarding decisions based on forwarding tables (similar to routing tables).
When a frame is received, the switch reads its [data link layer] destination address and sends the frame out the corresponding port in its forwarding table.
Switches making switching decisions based on data link layer addresses are called layer-2 switches.
When a switch is first turned on, its forwarding table is empty. It then learns which ports correspond to which computers by reading the source addresses of the incoming frames along with the port number that the frame arrived on.
If the switch’s forwarding table does not have the destination address of the frame, it broadcasts the frame to all ports.
Thus, a switch starts by working like a hub and then works more and more as a switch as it fills its forwarding table.

33. Media Access Control
Switched Ethernet still uses CSMA/CD media access control, but collisions are less likely as each network segment operates independently.
The network’s modified topology also allows multiple messages to be sent at one time.
For example, computer A can send a message to computer B at the same time that computer C sends one to computer D.
If two computers send frames to the same destination at the same time, the switch stores the second frame in memory until it has finished sending the first, then forwards the second.

34. 802.3 Ethernet versus switched Ethernet

35. Performance Benefits
Switched Ethernet can dramatically improve network performance.
Shared Ethernet 10BaseT networks are only capable of using about 50% of capacity before collisions are a problem
Switched Ethernet, however, runs at up to 95% capacity on 10BaseT.
Another performance improvement can be made by using a 10/100 switch that uses a 100BaseT connection for the server(s) and/or routers, i.e., the network segments experiencing the highest volume of LAN traffic.

36. Wireless Ethernet (IEEE 802.11)
Wireless LANs dispense with cables and use radio or infrared frequencies to transmit signals through the air.
WLANs are growing in popularity because they eliminate cabling and facilitate network access from a variety of locations and for mobile workers (as in a hospital).
The most common wireless networking standard is IEEE , often called Wireless Ethernet or Wireless LAN.

37. Wireless LAN Topology
WLAN topologies are the same as on Ethernet: physical star, logical bus
Wireless LAN devices use the same radio frequencies, so they must take turns using the network.
Instead of hubs, WLANs use devices called access points (AP). Maximum transmission range is about feet. Usually a set of APs are installed making wireless access possible in several areas in a building or corporate campus.
Each WLAN computer uses an NIC that transmits radio signals to the AP.
Because of the ease of access, security is a potential problem, so IEEE uses 40-bit data encryption to prevent eavesdropping.

38. A wireless Ethernet access point
connected into an Ethernet Switch.

39. WLAN Media Access Control
Wireless LANs use CSMA/CA where CA = collision avoidance (CA). With CA, a station waits until another station is finished transmitting plus an additional random period of time before sending anything.
Two different WLAN MAC techniques are now in use: the Physical Carrier Sense Method and the Virtual Carrier Sense Method.

40. Physical Carrier Sense Method
In the physical carrier sense method, a node that wants to send first listens to make sure that the transmitting node has finished, then waits a period of time longer.
Each frame is sent using the Stop and Wait ARQ, so by waiting, the listening node can detect that the sending node has finished and can then begin sending its transmission.
With Wireless LANs, ACK/NAK signals are sent a short time after a frame is received, while stations wishing to send a frame wait a somewhat longer time, ensuring that no collision will occur.

41. Virtual Carrier Sense Method
When a computer on a Wireless LAN is near the transmission limits of the AP at one end and another computer is near the transmission limits at the other end of the AP’s range, both computers may be able to transmit to the AP, but can not detect each other’s signals.
This is known as the hidden node problem. When it occurs, the physical carrier sense method will not work.
The virtual carrier sense method solves this problem by having a transmitting station first send a request to send (RTS) signal to the AP. If the AP responds with a clear to send (CTS) signal, the computer wishing to send a frame can then begin transmitting.

42. Types of Wireless Ethernet
Two forms of the IEEE b standard currently exist, utilizing the 2.5 GHz band:
Direct Sequence Spread Spectrum (DSSS) uses the entire frequency band to transmit information. DSSS is capable of data rates of up to 11 Mbps with fallback rates of 5.5, 2 and 1 Mbps. Lower rates are used when interference or congestion occurs.
Frequency Hopping Spread Spectrum (FHSS) divides the frequency band into a series of channels and then changes its frequency channel about every half a second, using a pseudorandom sequence. FHSS is more secure, but is only capable of data rates of 1 or 2 Mbps.
IEEE a uses Orthogonal Frequency Division Multiplexing (OFDM), operates in the 5 GHz band with data rates of up to 54 Mbps.
IEEE g uses OFDM in the 2.5 GHz band, operates at up to 54 Mbps, and is compatible with b

43. Infrared Wireless LANs
Infrared WLANs are less flexible than IEEE WLANs because, as with TV remote controls that are also infrared based, they require line of sight to work.
Infrared Hubs and NICs are usually mounted in fixed positions to ensure they will hit their targets.
The main advantage of infrared WLANs is reduced wiring.
A new version, called diffuse infrared, operates without a direct line of sight by bouncing the infrared signal off of walls, but is only able to operate within a single room and at distances of only about feet.

44. Infrared Wireless LAN

45. Bluetooth
Bluetooth is a 1 Mbps wireless standard developed for piconets, small personal or home networks.
It may soon be standardized as IEEE
Although Bluetooth uses the same 2.4 GHz band as Wireless LANs it is not compatible with the IEEE standard and so can not be used in locations that use the Wireless LANs.
Bluetooth’s controlled MAC technique uses a master device that polls up to 8 “slave” devices.
Examples of Bluetooth applications include; linking a wireless mouse, a telephone headset, or a Palm handheld computer to a home network.

46. Improving LAN Performance
As networks become more and more intensively used, LAN performance becomes a critical issue.
The measure of LAN Performance is throughput, i.e., the total amount of user data transmitted in a given period of time.
LAN performance can be improved by identifying and eliminating bottlenecks, that is, points in the network where congestion is occurring because the network or device can’t handle all of the demand it is experiencing.

47. Identifying Network Bottlenecks
Two common network bottlenecks are related to server access:
If server performance is poor when server utilization is high (>60%), then the bottleneck is the server.
If server performance is poor during periods of low server utilization (<40%), then the bottleneck is not the server but the network circuit.

48. Improving Server Performance
Two types of server performance improvements are possible:
Software improvements such as choosing a faster Network Operating System, fine tuning network and NOS parameters for optimal performance.
Hardware improvements such as adding a second server, upgrading the server’s CPU, increasing its memory space, adding more hard drives or adding a second NIC to the server.

49. Improving Server Performance: RAID
Improving disk drive performance is especially important, since disk reads are the slowest task the server needs to do.
Replacing one large drive with many small ones can improve server performance.
RAID or Redundant Array of Inexpensive Disks, builds on this idea. RAID system can be used to both improve performance and increase reliability by building redundancy into the hard drives, so that a hard drive failure does not result in any loss of data.

50. Improving Circuit Capacity
Improving circuit capacity can be done simply by upgrading one or all segments of a network to a faster protocol (which also means upgrading the NICs), such as;
Upgrading the network from 10BaseT to 100BaseT, or
Upgrading the network segment to the server from 10BaseT to 100BaseT
Another approach to improving circuit capacity is by increasing the number of network segments to the server. Most servers can handle several network segments simply by adding additional NIC cards, thereby increasing access to the server

51. Network Segmentation: a. Before b. After

52. Reducing Network Demand
Performance can also be improved by reducing network demand. This can be done by:
Moving more files, such as heavily used software packages to client computers.
Disk caching, software on client machines can also reduce server demand.
Moving user demands from peak times to off peak times, by telling network users when peak usage times occur and encouraging users to not use the network as heavily during these times can also help improve performance.
Delaying some network intensive jobs to off-peak times, such as running heavy printing jobs at night, can also improve performance.

53. Improving LAN performance
Increase Server Performance
Software: Fine-tune the NOS settings
Hardware:
Add more servers and spread the network applications across the servers to balance the load
Upgrade to a faster computer
Increase the server's memory
Increase the number and speed of the server's hard disk(s)
Upgrade to a faster NIC
Increase Circuit Capacity
Upgrade to a faster circuit
Segment the network
Reduce Network Demand
Move files from the server to the client computers
Increase the use of disk caching on client computers
Change user behavior