1. About Innomag: Overview
Innovative Mag-Drive has been manufacturing sealless, non-metallic, magnetically driven pumps since 1998.
Today, most in the pumping industry, recognizes Innomag as a leader and major innovator in the pump industry.

2. Vertically Integrated
INNOMAG pumps are made and assembled in our factory in the USA

3. TB-Mag Series -Thrust Balancing
Highest Quality Components

4. About Innomag: The Company Cont.
Fast prototyping
Fast lead times
Close cooperation with vendors
Highly Experienced Engineering design team
Innomag does as much processing/manufacturing in-house and works very closely with all of their vendors to achieve consistent, quality results.
Being in control of the process, allows us to adapt quickly and with our unrivaled experience, we can offer the fastest prototyping and lead times in the industry.

5. About Innomag – Pump testing
All wet-ends run tested
Disassembled and Inspected
Hydrostatic tested to 450 psi (31 bar)
50Hz and variable speed testing available.

6. TB-Mag Series - Overview
ASME/ANSI and ISO models.
Continuous duty process pumps

7. TB-mag Series - Construction and features
Thrust balanced
Solids handling – unique to mag-drives
Permeation protected magnets
Single piece impeller
Totally open suction, lowest NPSHr

8. TB-Mag Series -Thrust Balancing
By creating distinct pressure zones in the pump, we can use those pressures to regulate & control the forces on the impeller
As the impeller moves forward, the pressure surrounding the inner magnet is reduced. This creates a restoring force. For momentary excursions, the impeller will bounce back. For prolonged changes, impeller will seek new equilibrium position
Division takes place via the two sets of wear rings. The pump is then divided into the suction pressure, the discharge/volute pressure, and the balance presure. As the impeller moves forward, the variable orifice between the shaft and the thrust control valve increases, which in turn, lower the pressure(ex: taking your thumb off a garden hose).

9. TB-Mag Series - Thrust Balancing Close up

10. TB-Mag Series - Solids Handling 2D View
Wear rings create a clearance of only 0.005” (.127mm), anything larger can’t hurt the magnets or lock up the bearings.
Solids Handling
TB-Mag Series - Solids Handling 2D View

11. TB-Mag Series - Solids Handling Intro
Superior Solids Handling
TB-mags can handle solids up to 30%
If it can travel through the vanes of the impeller, the pump can handle it
Solids must be softer than SiC
Start-up and shut-down must be evaluated
Erosion must still be considered
TB-Mag Series - Solids Handling Intro

12. TB-Mag Series - Tru-Seal Permeation Protection
INNOMAG Single Piece Impeller
All fluoroplastics are inherently permeable.
While the fluoroplastics are extremely chemical resistant, the magnets are not.
Magnets are covered with a stainless can, welded air tight, before being encapsulated in plastic. This patented process is the best permeation protection available.
Greatly extends the impeller life due to fluorine or chlorine ions that permeate the plastic and attack the magnets. Lifespan for an unprotected impeller is between 6-14 months.
2 piece impellers do not save you money as failures usually result in damage to both the impeller AND magnet assembly, completely negating the benefits of a 2 piece impeller.
TB-Mag Series - Tru-Seal Permeation Protection

13. TB-Mag Series - Cantilevered Design
Cantilevered Shaft Design
INNOMAG
COMPETITION
TB-Mag Series - Cantilevered Design
Unique Design
Fully open suction
Lowest NPSHr
Better Efficiencies

14. U-Mag Series - Features
Sub-ANSI model
Thrust forward design
Universal flanges for complete compatibility
Virgin PFA option for semiconductor, pharmaceutical, or other high purity industry
Same chemical compatibility as TB-mag with double welded impeller
Low Cost
The U-Mag Series
U-Mag Series - Features

15. U-Mag Series - Construction
U-Mag Construction
Optional High Purity PFA
Mates NEMA C-faced or IEC D-flange motors directly (no spacer plates required).
Universal chemical resistance with fluoroplastic ETFE as standard.
Universal foot supports entire pump load.
Fully bonded ETFE or optional High Purity PFA liner - minimum of 1/8” (3 mm) thick and rated to full vacuum.
Fully open suction for lowest NPSHr.

16. U-Mag Series - PFA PFA High purity fluoroplastic
Ultra low contaminants, tested to less than 2 PPB.
Excellent for semi-conductor, LCD and circuit board manufacturing

17. Applications - Semiconductor Industry
Semiconductor/PCB Industry
Applications - Semiconductor Industry
High purity standards require PFA material on process/recycle streams
Acids and other etching solutions(HF, HCL, etc.)
Acetone
Hydrogen Peroxide
MEK, methanol, peroxide, TMAH
Xylene
Caustic

18. Case Studies - Fortune 500 Customers
Some INNOMAG electronics customers