2. Torching Equipment Fire Extinguishers Pre-Job In-Progress Post-Job Safe Practices Potpourri 10 20 30 40 50

3. Question 1 - 10 Part of the regulator that must always be kept clean.

4. Answer 1 – 10 What is the “Vent Hole” Vent Hole

5. Question 1 - 20 Never use a torch missing this part.

6. Answer 1 – 20 What is the “Stand”

7. Question 1 - 30 If a pressure regulator leaks check to see if this part is in place.

8. Answer 1 – 30 What is an “O” ring “O” Ring

9. Question 1 - 40 Use this tool to light a torch.

10. Answer 1 – 40 What is a “striker”

11. Question 1 - 50 Used for quick application of field rolls.

12. Answer 1 – 50 What is a “Torch Trolley” or “Dragon Wagon”

13. Question 2 - 10 What words does the term PASS stand for?

14. Answer 2 – 10

15. Question 2 - 20 Two of these must be within 10’ of torching operations.

16. Answer 2 – 20 What is two 4A-60BC fire extinguishers

17. Question 2 - 30 This must be in the fire extinguisher to ensure it has not been used.

18. Answer 2 – 30 What is a plastic seal band in place through the release pin.

19. Question 2 - 40 The safe distance that a fire extinguisher should be from a propane tank.

20. Answer 2 – 40 What is no closer than 10 feet 10 feet

21. Question 2 - 50 The types of fires a class A fire extinguisher should be used on.

22. Answer 2 – 50 What is Wood Paper Plastic Cloth

23. Question 3 - 10 Must be performed for 2-hours after last torch is turned off.

24. Answer 3 – 10 What is fire watch

25. Question 3 - 20 Secure in the center of the roof during fire watch duties

26. Answer 3 – 20 What are LP tanks

27. Question 3 - 30 Helps detect if under membrane smoldering or fire is occurring.

28. Answer 3 – 30 What is a Infrared Heat Detector

29. Questions 3 – 40 Eliminates hazards before the job starts

30. Answer 3 – 40 What is a Pre-Job Inspection

31. Question 3 - 50 Does not have to be CERTA certified but must be knowledgeable in his/her duties

32. Answer 3 – 50 What is the person performing fire watch

33. Question 4 - 10 Safest way to avoid fire hazards when torching at walls, penetrations, roof edges and unseen areas.

34. Answer 4 – 10 What is torch-and –flop method

35. Question 4 - 20 ¾ inch perlite ¾ inch fiberglass ¼ inch glass faced gypsum board

36. Answer 4 – 20 What are acceptable thermal barrier insulation boards

37. Question 4 - 30 Used for direct torching at walls and penetrations if acceptable thermal air barrier is in place.

38. Answer 4 – 30 What is a Detail Torch

39. Question 4 - 40 Shut off the torch

40. Answer 4 – 40 What is if you leave a torch unattended

41. Question 4 - 50 A lit torch must only be placed here

42. Answer 4 – 50 What is the “Stand”

43. Question 5 - 10 All torch applicators should be trained in these safe practices.

44. Answer 5 – 10 Fire hazards recognition LP equipment safety Wear appropriate PPE Proper use of a fire extinguisher

45. Question 5 - 20 Up to date inspection tags on the fire extinguishers provide guarantee that….

46. Answer 5 – 20 What is fully charged

47. Question 5 - 30 Careless torch activities lead to this.

48. Answer 5 – 30 What is unemployment

49. Question 5 - 40 Never torch directly to

50. Answer 5 – 40 What are Combustible Substrates

51. Question 5 - 50 Roofs on types of businesses that we should never torch to

52. Answer 5 – 50 What are Restaurants and Laundromats