4. Instrument which measures and detects seismic waves/vibrations  Weight and pen remain still during an earthquake; drum moves with the Earth  Earthquake measuring stations have at least 3 seismographs  Locations of epicenters are determined using data from 3 measuring stations Photo courtesy of : http://www.thetech.org/exhibits/online/quakes/seismo/

6. Written record of earthquake waves Used to determine epicenter and when earthquakes occurred Shows magnitude (strength) of waves with height of lines

7. Epicenter: surface origin of seismic waves (surface waves) directly above focus Focus: underground point of origin for earthquake body waves

10. *Primary or Pressure waves *fastest *travel through solid, liquid, gas *alter speed due to density;the denser the material, the faster they move *push-pull waves *rock moves back and forth in the direction of the wave

12. *Secondary waves *travel through solids only *the denser the material, the faster these move *rocks move side to side at right angles to the direction of the wave

14. *L waves *slowest moving; originate at epicenter *cause the most serious damage *travel along the surface of the Earth *move crust up and down & back and forth

17. Why do you need 3 stations reporting the same earthquake data? Triangulation results in one epicenter location.

18. What information do you need from the 3 reporting stations and why do you need it? The difference in arrival times of the P and S waves (lag time) and then the distance to the epicenter The lag time determines the epicenter.

19. Which of the stations is farthest from the epicenter? Which of the stations is closest? How do you know?

20. 1 2 3

21. S-P Time Method:  Collect data from at least 3 seismograms from an earthquake  Use the Time-Distance graph to find distance from epicenter for each seismogram  Use each distance to draw a circle of possible epicenters  The actual earthquake epicenter is found at the spot where all 3 intersect

22. Strength of earthquake waves Measured by Richter Scale Scale from 0-10 Each increasing number is 10x more ground shaking A measure of how much damage is done and the degree to which an earthquake is felt by people Measured by Modified Mercalli Scale Scale from I-XII Each location that felt the event will have a different intensity level

23. A magnitude 8.7 earthquake is 794 times BIGGER on a seismogram than a magnitude 5.8 earthquake. The magnitude scale is logarithmic, so (10**8.7)/(10**5.8) = (5.01*10**9)/(6.31*10**6) =.794*10**3 = 794 OR = 10**(8.7-5.8) = 10**2.9 = 794.328 Another way to get about the same answer without using a calculator is that since 1 unit of magnitude is 10 times the amplitude on a seismogram and 0.1 unit of magnitude is about 1.3 times the amplitude, we can get, 10 * 10 * 10 / 1.3 = 769 times [not exact, but a decent approximation] The magnitude scale is really comparing amplitudes of waves on a seismogram, not the STRENGTH (energy) of the quakes. So, a magnitude 8.7 is 794 times bigger than a 5.8 quake as measured on seismograms, but the 8.7 quake is about 23,000 times STRONGER than the 5.8! Since it is really the energy or strength that knocks down buildings, this is really the more important comparison. This means that it would take about 23,000 quakes of magnitude 5.8 to equal the energy released by one magnitude 8.7 event. Here's how we get that number:

24. One whole unit of magnitude represents approximately 32 times (actually 10**1.5 times) the energy, based on a long- standing empirical formula that says log(E) is proportional to 1.5M, where E is energy and M is magnitude. This means that a change of 0.1 in magnitude is about 1.4 times the energy release. Therefore, using the shortcut shown eartlier for the amplitude calculation, the energy is, 32 * 32 * 32 / 1.4 = 23,405 or about 23,000 The actual formula would be: ((10**1.5)**8.7)/((10**1.5)**5.8) = 10**(1.5*(8.7-5.8)) = 10**(1.5*2.9) = 22,387 This explains why big quakes are so much more devastating than small ones. The amplitude ("size") differences are big enough, but the energy ("strength") differences are huge. The amplitude numbers are neater and a little easier to explain, which is why those are used more often in publications. But it's the energy that does the damage.

25. Liquefaction Vibrations cause pressure in ground water between grains of sand and silt. This turns sand into a viscous liquid ”quicksand”.

26. Tsunamis giant waves that travel at speeds of 700-800 km/hr and reach height of 20+meters

27. Earthquake hazard is a measurement of how likely an area is to have damaging quakes in the future. It ’ s deter- mined by past and present seismic activity

28. Seismologists look for patterns in earthquake data to try and predict future earthquakes. The strength and frequency are important factors in the prediction of earthquakes. Some seismologists believe that a major earthquake is more likely to occur along part of an active fault that have had few or no earthquakes happen in recent times. This is known as the …

29. Used to predict the Quake of ’ 89 (Loma Prieta) The area along an active fault where few earthquakes have happened is called a seismic gap. The location and magnitude of this quake was predicted by using the gap hypothesis.

30. Changes in speed of P and S waves Other observations that may be helpful when predicting ‘ quakes include: Changes in the tilt of the Earth’s surface

31. Changes in the behavior of animals These methods are not completely accurate and will only suggest that an earthquake may occur Changes in water level (lakes, streams, wells, etc.)

32. Space-based technology helps geologists identify movement patterns that precede major earthquakes.

33. Mass damper- helps compensate for building movement Active tendon system- helps compensate for building movement Base isolators- shock absorbers that stop the passing of seismic waves Cross braces-counteracts the pull and push stresses Flexible pipes- prevent water and gas lines from rupturing Some things that help:

35. A lead-rubber bearing is made from layers of rubbers sandwiched together with layers of steel. In the middle of the bearing is a solid lead "plug." On top and bottom, the bearing is fitted with steel plates which are used to attach the bearing to the building and foundation. (See Figure 2) The bearing is very stiff and strong in the vertical direction, but flexible in the horizontal direction.

36. Before: Survival supplies Identify safe zones inside and outside Evacuation plan and plan where to meet During: Inside-Seek cover under table, desk, Outside- Face down away from buildings, trees, powerlines After: Stay out of damaged buildings, be prepared for aftershocks