1. 7/23/20021 What do you expect from a Cellular service Provider - LOW SUBSCRIPTION FEE - HIGH QUALITY CONNECTION

2. 7/23/20022 Outline Review of the wireless network operation Limitations of the current network architecture Description of the new architecture and benefits Backhaul cost reduction: Analysis and results Increased availability: Analysis and results Conclusions Further research topics

3. 7/23/20023 A Simple Wireless Network Mobile Data Set PSTN Packet Network Mobile Voice Unit Base Transceiver System (BTS) Base Station Controller (BSC) Mobile Switching Center (MSC) Packet Inter- Working Function Challenge is to keep connection and not loose any data during handoff operation

4. 7/23/20024 The Components BTS –BTS consists of one or more transceivers placed at a single location. The BTS terminates the radio path on the network side. BSC –Provides allocation and management of radio resources. –SDU: Selection and distribution unit. Also responsible for handoff coordination MSC –Provides and controls mobile access to the PSTN. Interprets the dialed number, routes and switches call to destination number. Also manages mobile’s supplementary services. Maintains a register of visitors operating within the coverage area of the MSC’s connected BTSs. PDSN: Packet data service node is basically a packet router.

5. 7/23/20025 MSCPDSN BSC (SDU) BSC (SDU) BSC (SDU) BTS - Backhaul cost is by $$$/mile - 10-100 miles between BTS and BSC - Voice or data use one DS0 channel at a time - BTSs are located in the tower - BSC and MSCs are located in the central office Current Wireless Network Architecture BSC BTS 24xDs0 in T1 Packets TDM channels TDM channels

6. 7/23/20026 Soft Handoff between two BTS Handoffs == ( Hard || Soft ) Handoff: A handoff mechanism is needed to maintain connectivity as devices move, while minimizing disruptions to ongoing calls. This mechanism should exhibit low latency, incur little or no data loss, and scale to a large network.”

7. 7/23/20027 SDU and soft handoff SDU-1 WR-A SDU-1- SDU-2 WR-B - - 3 to 6 BTSs involved in soft handoff - SDU changeover due to weak signal from primary BTS - BTS forwards even corrupted radio frames to the SDU for selection SDU-2- BTS-1 BTS-2 BTS-3

8. 7/23/20028 Problems with the current architecture Duplicate traffic on the links: Frame selection is done at the BSC (One frame is generated for each soft handoff leg.) This results in duplicate traffic flow at the backhaul No traffic aggregation: Each call is allocated DS0 capacity. Even when there is no activity on the call, the DS0 is reserved. At this rate, currently each BTS can support only around 20 calls per sector (normally 3 sectors per BTS). So, no traffic aggregation – does not utilize statistical multiplexing (results in inefficient backhaul link provisioning) If six BTS, then more overhead: Seventy percent (70%) of wireless operators expenditure is on RAN. Around 30% expenses are backhaul cost. Only 15% of the BTS-BSC traffic is payload and rest is overhead. If six BTS are involved in the soft handoff then the overhead will be lot higher. Carries dead payload: BTS forwards even error frames to BSC. Because the selection is done at the BSC. This means we are carrying dead payload to BSC.

9. 7/23/20029 Problems with the current architecture (cont..) Uneven utilization of links: For data services as well as voice, IP networks overlay on top of current wireless networks. This is very inefficient, not cost effective, and very difficult to deploy the new services. Performance: Less propagation delay. Currently, for some of the BTS-BSC configurations, the links run 100 miles, it means several milliseconds of delay. This creates problem during soft handoff. Availability: Less availability due to single point of failure (in terms of base stations, base station controllers and links connecting between them)

10. 7/23/200210 Review Simple wireless network operation Different components in the network Wireless network topology Mobility and soft handoff Problems with the existing architecture

11. 7/23/200211 Typical US city BTS Map 30x30 miles Urban Rural highway

12. 7/23/200212 Solution: Distributed Control GR Gateway Router WR GR Gateway Router Radio frames Embedded in IP packets Each packet Contains several radio frames. Wireless Router is an IP router with RF termination. Functions include BTS, SDU, power control, and handoff control Gateway Router is a IP router connected to the internet core

13. 7/23/200213 WR-WR Links WR-WR Links WR WR/BTS GR Gateway Router WR WR/BTS GR Gateway Router GR-GR links WR-GR links Solution (cont.) - Radio frame routing using IP routing - Radio neighbors exchange resource info. using IP routing protocols - Mobility is handled through IP signaling protocols - Radio resource management is handled by IP traffic management - WR assumes SDU function Transit traffic management is handled by IP routing, QoS

14. 7/23/200214 Solution (cont.) –Distributed SDU. Distributed bearer and control –Radio Routing Protocol: IP routing merged with Radio frame routing for soft handoff and mobility. Wireless extensions of OSPF with radio neighbors. –Radio Discovery Protocol: Discovering Radio Neighbors –Radio Resource Management: IP traffic management merged/enhanced with Radio Traffic Management. Radio Power Control integrated and aligned with IP QoS –RSVP extensions for Radio: IP resource management merged/enhanced with Radio Resource Management. For example, Radio Resource Management and soft hand off signaled with RSVP. –IP transport in Radio Access Network Disruptive Technology

15. 7/23/200215 Benefits Cost Reduction: Efficient use of backhaul links and aggregation. Only 15% of the BTS-BSC traffic is payload and rest is overhead. Around 30% expenses are backhaul cost. Objective is to reduce the backhaul traffic and small number of high speed backhaul links. Scalability: –Separation of call processing and bearer paths –Distributed SDU and Distributed Control –Ability to provide coverage and capacity during peak hours Redundancy and Availability: Due to meshed architecture, network is robust and works around the failures.

16. 7/23/200216 Benefits (continued) Marriage of IP and wireless protocols: Seamless operation of IP-Network-Layer with Radio Control. Reuse already deployed routers in the Central Offices. New wireless services: Automatic Reconfiguration of Radio Access Network. Expand cell attributes to provide more capacity Performance: Less propagation delay. Currently, for some of the BTS-BSC configurations, the links run 100 miles, it means several milliseconds of delay. This creates problem during soft handoff. Due to short lengths between base stations, the delay will be negligible.

17. 7/23/200217 2G/3G RAN Network (Traditional) CO BTS CO BSC Interoffice distance (costs per mile) cost + Fixed Cost Channel Termination Cost Channel Termination Cost MSC

18. 7/23/200218 What configuration is best in terms of cost and availability Cost Reduction: How and where to place wireless router in the RAN network with respect to network-level backhaul cost and availability. For example, existing WR can be part of GSR (high end router) ? How close it to BTS Higher Availability: Distributed IP-RAN for backhaul cost savings and higher availability Variables in analysis –Different kinds of transport cost structures –Different types of links (T1/T3/Microwave etc.) –Different types of connectivity between BTS and wireless router –Number of carriers supported supported by BTS

19. 7/23/200219 Cost Model Commercial BTS network topology. BTS are connected to BSC using the chain of Central Offices. Real ILEC cost structure is assumed for the T1 leased lines from urban and rural areas to the BSC. 20-30 Node network in urban area and 10 BTS in rural areas. Soft hand factor of 2.0: How many BTS are in soft handoff 1.5 T1 per BTS per carrier BTS Network Regions: I) Dense Urban, ii) Urban iii) Suburban iv) Rural Cost models –Channel termination costs –Interoffice fixed costs –Per mile costs: Transport cost changes according to distance and the type of transport (T1/T3/OC3)

20. 7/23/200220 Configurations Four BTS network configuration are considered: 1.Traditional BTS-BSC network (Config-1, fully star, call it “Traditional”) 2.One Wireless Router supporting multiple BTSs (10-30). For example, existing WR can be part of GSR (high end router) ? How close it to BTS (Config-2, call it “star”) 3.Meshed Wireless Routers (Config-3, one wireless router per BTS, full mesh within the central office region. Call this “WR”) 4.Meshed Wireless Routers (WR) and each WR connected to multiple Gateway Routers for higher availability (Config-4, with connection to all the nearby high end routers. Call this “WR-HA”)

21. 7/23/200221 2G/3G RAN Network (Traditional) CO BTS CO BSC Interoffice distance (costs per mile) cost + Fixed Cost Channel Termination Cost Channel Termination Cost MSC - Around 150 BTS per BSC

22. 7/23/200222 WR supports multiple BTS (10-20). Selection and distribution is done in the WR. WR collocated with CO WR supporting multiple BTSs (Star Topology) WR WR-BTS links BTS WR WR-BTS links BTS CO

23. 7/23/200223 WR collocated with BTS (WR) WR-GR links WR WR/BTS Central Office WR-WR Links GR Gateway Router WR-GR links WR WR/BTS Central Office WR-WR Links GR Gateway Router * WR-GR link (primarily) used for backhauling selected traffic to the destination * WR-WR link (primarily) is used for selection and distribution traffic between two wireless routers. * GR-GR links are links between two IP routers. These routers do not distinguish between wireless and wireline traffic GR-GR links

24. 7/23/200224 WR collocated with BTS with HA (WR-HA) WR-GR links WR WR/BTS Central Office WR-WR Links GR Gateway Router WR WR/BTS Central Office WR-WR Links GR Gateway Router GR is collocated in the the closest CO Connectivity to two (atleast) GRs is established for higher availability. The second GR is collocated in the neighboring Central office.

25. 7/23/200225 Traffic Models scheduler Overhead / container Overhead / stream Overhead / stream voice stream voice stream multiplexer packetizer  t multiplexer packetizer  t Overhead / stream Overhead / stream data stream data stream Segment. Traffic Mix 100% voice + 0% data 100% data, 14.4K, 64K and 144Kbps 80 % voice + 20% data, 14.4K, 64K and 144Kbps 20 % voice + 80% data, 14.4K, 64K and 144Kbps

26. 7/23/200226 Cost Comparisons—Urban (30 node network) Star (10 BTS per WR) No. of Carriers (increased bandwidth at BTS, 1carrier requires ~~2 Mpbs) $$$$$

27. 7/23/200227 Cost Comparison—Rural (around 10 nodes) No. of Carriers (increased bandwidth at BTS, 1carrier requires ~~2 Mpbs) $$$$

28. 7/23/200228 Why less cost ?? Backhaul cost reduced with WR mesh architecture. Customer saves $$$$ (per mile backhaul cost) Why is the backhaul much less with WR? What is new with WR? – Frame Selection is done at the WR. No duplicate traffic after the selection is done – The aggregation of voice and data traffic from multiple WRs enables better Statistical multiplexing and reduces the backhaul requirement. This also enables customer to use less costly T3 and saves them more $$$$ – Flexible and more reliable traffic routing.

29. 7/23/200229 Review and Conclusions Statistical multiplexing and compression techniques are not accounted in the results described. If counted, more savings are realized Cost savings for one carrier are not much but substantial for multiple carriers. Star at the near-by-CO with a high speed (e.g., DS3/OC3) uplink is the optimum but without higher availability. Mesh is ideal for higher availability and cost savings All the WR cases win over traditional deployment Ongoing work: Different kinds of transport cost structures and different types of links (T1/T3/Microwave etc.)

30. 7/23/200230 Service Availability CO BSC MSC BTS WR - Rerouting around failed links/nodes - Rerouting around congested links/nodes - Wireless router is also IP router hence no need to deploy full mesh - If BTS fails, neighboring resources can be used to complete the calls. -Single point of failure at BTS - Single point of failure at BSC - No rerouting around congested nodes possible.

31. 7/23/200231 Availability Model (example) Tower WR GR Backplane Line Card Line card Control Processor Control Processor SW Calculate MTBF and MTTR of all the components in each element

32. 7/23/200232 Annual Down Time Comparison Link Avail.99.999.9999.99999 Traditional (Hours) 17417.772.010.438 WR-HA (Minutes) 5.25 BTS Availability: 0.99999 GR Availability: 0.99999 Link availability is varied from 0.99 to 0.99999 and downtime is computed For traditional and WR-HA network topologies.

33. 7/23/200233 Annual Down Time Comparison Link Avail.99.999.9999.99999 Traditional (Hours) 17417.772.010.438 WR-HA (Minutes) 5.855.78 Assumptions: BTS Availability: 0.99999 GR Availability: 0.99 Link availability is varied from 0.99 to 0.99999 and downtime is computed For traditional (2G/3G) and WR-HA network topologies.

34. 7/23/200234 RESULTS In conventional case, when a link fails, the call level reliability is low because the call is not redirected without dropping. However, in mesh architecture, the call can still be maintained and the rerouting takes place at the frame/packet level. Though GR’s availability is only 0.99, the overall service downtime is not impacted due to the fact that there are multiple paths from BTS to another GR.

35. 7/23/200235 Review and Conclusions Distributed RAN architecture saves backhaul cost (less than half of the cost of existing architecture ) Distributed RAN architecture supports 99.999% service-level availability compared to conventional network. In fact, full mesh is not required for realizing the 99.999% availability. Even partial mesh can achieve this level of availability Distributed architecture increases the complexity of control and requires working prototype for understanding the new protocols. Disruptive technology: Required new protocols design and approval from vendor and hence may take long time to get to the field (this is weakness in this architecture).

36. 7/23/200236 Further Work

37. 7/23/200237 Content Based SDU The solution in this patent describes how loss/delay/delay variation objectives are met for different services in SDU. These SDUs cater to different loss, delay and jitter budget requirements. The SDU selection and its parameters are setup during the call setup. If the call characteristics change during the duration of the call, the behavior of the SDU is also changed. A three dimensional grid, with each dimension representing loss, delay, jitter, is defined. Next, each service is placed in this grid depending on how sensitive the service is with respect to loss, delay or delay sensitivity. Advantages  Efficient traffic engineering  Extension of the service level agreements to provide a comprehensive QoS  Enhancement of end to end QoS

38. 7/23/200238 Fast and Smooth SDU change over Fast and smooth SDU (anchor) handover between two wireless routers.  Fast means low latency and smooth means no packet loss.  Frame-level handover between two wireless routers  Handover mechanism should coexist with native IP or Mobil-IP (either version 4 or version 6) protocol defined by IETF (at network layer)  Handover should also be transparent to the mobile.  Handover mechanism should be applicable to UMTS/CDMA 2000.

39. 7/23/200239 Wireless Content Processor (WCP) Problem: To date, the size and cost of Wireless equipments like BTS, BSC, MSC, SGSN, GGSN, and PDSN are huge (cost and space) and there are different technologies for different standards (2G, 2.5G, 3G, CDMA, GPRS, UMTS). Vendors have separate boxes (examples listed above) for each of these technologies. Wireless Service providers are asked to invest huge amount for these overlapping technologies covering the same geographical areas. In addition, these technologies and standards are changing very rapidly. For cost-savings, space-savings, scalability, back-haul savings, rapid deployment of new services, and efficient air coverage it is imperative to introduce programmable wireless-content-specific network processors.

40. 7/23/200240 Wireless Content Process (WCP) Proposed Solution: Network processors being developed in the current industry are specially designed for the wireline-data processing. To our knowledge, there is no body developing the wireless-specific content processors. This paper describes the WCP role in wireless-specific content processing. Several new and existing services can be enabled by using the WCP and these will be described in this document. In particular, how WCP can process wireless protocols and control bearer paths, associate bearer paths with signaling will be described in this paper. In addition, WCP role in scaling PDSN and other wireless network elements will be described.