1. Calibration Measurement Requirement Summary
Modernization and
Calibration Measurement Requirement Summary
CMRS
Greg Hogan
NSWC Corona Det Seal Beach

2. Life Cycle Stages Technical Measurement Requirement
Developed from Prime System requirements
Contracting/Active Procurement
Working with Industry to get best value
Warranty Coverage
Included in contract negotiation, ideally 3-5 years if available
Post-Warranty Support
RCC or OEM, most logistically efficient
Legacy Support
Designated Overhaul Point establishment and/or ‘Fly-til-Fail’ with technology back-up or alternative/shift
Obsolescence
If requirement still exists, then process recycles

3. Known Life Cycle BITRs (Bumps In The Road)
Technical Measurement Requirement Definition
Contracting and Procurement
System developmental lead time may be insufficient to support fielding of TMDE in time for deployment schedules
Technology may no longer be available or cost effective
Obsolescence
Warranty Coverage
DRMO may not be option if capability still required but no longer supported by industry
May not be of sufficient duration, cost effective, or OEM may not be willing to accept risk
Legacy Support
Post-Warranty Support
Commercial & DoD infrastructure capabilities may not exist
Maintainability of technology may be proprietary/unique

4. Activity Interaction NAVSEA TMDE SUPPLY
RMC
Calibration Centers
INPUT
FEEDBACK
NAVSEA TMDE
Engineering & Lifecycle Logistics Team
Defined Measurement Disciplines
(Functional Groups)
TYCOMS & FLEET REPS
Individual
System Assessment
Grouped
System Requirements
RMCs
(Subject Matter Experts)
Categorized Measurement Requirements
(SCATs)
(Measurement Requirements)
PS/E Acquisition Programs
PS/E ISEAs
SUPPLY
(Purchase Description and Contract Award)
TMRs

5. Functional Groups Signal Generator Digital Multimeters
Baseband Generator
Synchro Resolver
Spectrum Analyzer
Calibrator
Logic Analyzer
Oscilloscope
Voltmeter
Frequency
LAN/WAN
Telcomm Analyzer
Power Supply
Bit Error Rate Tester
Comm Analyzer
Recorder
Insulation Breakdown
Power Analyzer
Component Test
Impedance Matcher
Field Strength
Noise
Radar Test Set
Modulation Analyzer
Probe
Power Meter
Attenuator
Fiber Optics
Distortion
Data Analyzer
Electrical Safety
Network Analyzer
Resistor
Scalar Analyzer
Photo Tachometer
Resistance
Capacitor
Amplifier
Humidity
Dummy Load
Temperature
Transformer
Time/Freq-Domain
Reflectometry Ph
Phase Sequence
Audio Analyzer
Sound Level
Termination
Data Acquisition
Modulator
Adapter
Coupler
Detector
Divider
Filter
Conductivity
Earth Ground
Echo Box
Isolator
Battery Analyzer
PCB Test
Impedance
Vibration
Oxygen
Switch
Potentiometer
Mixer
Power Limiter
Antenna
Inductor
Torque
Earth Ground
Signature Analyzer
Teletype
Monitor

6. Model obsolete without immediate direct replacement.
Obsolescence Issues
Model obsolete without immediate direct replacement.
Model no longer on contract.
OPN requirements forefront of identifying obsolete GPETE.
Conflicting equipment availability reports.
Vendors not being proactive in reporting model obsolescence.

7. Past Year Efforts 4017 METER RADIATION NBM-520+2 PRB 4019
SCAT_CD
MOD_DESCP_ABBP_TX
4017
METER RADIATION NBM PRB
4019
METER RADIATION NBM-520+4PRBS
4025
ANALYZER LOGIC 102 CH 100MHZ
4115
POWER SUPPLY 50VDC 1.5AMPS
4122
OHMMETER HI-RESOLUTION 2K OHMS
4236
METER CLAMP-ON AC 1000A 700V
4245
MULTIMETER 3.5 DGT AC,DC 1000V
4249
MULTIMETER 4.5 DGT AC/DC 1000V
4306
OSCILLOSCOPE FOUR TRACE 400MHZ
4553
TESTER SEMICONDUCTOR IC
4584
ANALYZER VOICE FREQ HZ
5359
TORQUE CALIBRATOR 0-800FT-LB
4541
MEGOHMMETER V 100GOHM
4465
LAN CABLE TESTER
4405
GENERATOR, FUNCTION

8. In Progress SCAT_CD MODEL DESCPRIPTION 4070 SYNCHRO TESTER 60+400HZ
4195
VOLTMETER 0DB/1V U-1000V
4262
METER DEVIATION FM MHZ
4290
TIME DOMAIN REFLECTOMETER
4298
4341
ANALYZER SPECTRUM 99HZ-1800MHZ
4344
ANALYZER DISTORTION KHZ
4362
GENERATOR FM/AM 50KHZ- 550MHZ
4363
GENERATOR AM/FM 9KHZ-2GHZ
4473
ANALYZER ANTENNA MHZ
4475
ANALYZER NETWORK 10MHZ-110GHZ
4659
TRANSFORMER ISOLATION 4:1 5KHZ
4734
ANALYZER SPECTRUM KHZ
4940
POWER METER PK GHZ

9. Upcoming
In process to evaluation next obsolescence SCAT codes for review. Possible candidates.
SCAT 4349 Audio Analyzer
SCAT 4466 Network Analyzer
SCAT 4591 Bit Rate Error Tester
SCAT 4567 Optiview II Network Analyzer
SCAT 4573 Network Analyzer
SCAT 4310 OTDR SM
SCAT 4318 OTDR MM
Fleet Input ___

10. CMRS
The Calibration and Measurement Requirements Summary is a form used to document the measurements O-Level maintainers could be required to make on a specific Prime System, and to calculate the test equipment that will be required to support those measurements.
Actual Prime System measurements are defined:
Volts, Amps, MHz, RPM, etc.
Required accuracies
Unique conditional requirements (rare)
Sufficiently capable test equipment is matched to each measurement using 4-to-1 Test Accuracy Ratio
Sufficiently capable cal standard or procedure is matched to the test equipment listed (also 4:1 TAR)
Category I
Category II
Category III

11. CMRS Responsibilities ISEAs/PEOs maintain Category I Data only
(Prime System)
NAVSEA TMDE Team will maintain Categories II and III (Test Equipment and Cal Standards)

12. CMRS Documentation
Once Prime System measurement requirements (Category I) are documented, NAVSEA completes remainder of CMRS. ISEA is then only responsible for updating O-level maintenance parameters when necessary.

13. Requirement Consolidation
NAVSEA uses consolidated CMRS data for all serviced PS/E to develop the best match of GPETE requirements to cost.
PS/E #1
PS/E #2
PS/E #n
Prime System
Measurement
Parameter
Meas 1 (Volts)
Meas 2 (Acc)
Meas 3 (Res) 
Meas n
System 1
850 Vdc
4 %
< 3.4 V 
System 2
795 Vdc
5 %
< 4 V 
System n
815 Vdc
10 %
< 8.2 V 
ISEA-
provided
Category I
data

14. The Bottom Line: Make use of GPETE whenever possible.
Once an ISEA completes the Category I data portion of the CMRS, NAVSEA then calculates and completes Category II and III. The complete CMRS for each system is then validated by the ISEA. Once validated, the responsibility to maintain a sufficiently capable and reliable inventory of GPETE and calibration standards rests with NAVSEA 04RM.
Assuming the O-Level maintenance requirements for a given system do not change, the only further ISEA action in support of CMRS is to keep POC data current.
NAVSEA will advise ISEAs when compatibility or technology advance/obsolescence compels a change in Category II equipment, and will resolve any needed shifts with the ISEA.

15. Over 120 CMRS completed to date
AN-BYK-6(V)1 CMRS
AN_BYH-1 CMRS
AN_BST-2 Cmrs form
BSR-1 Cmrs Template
AN-BSQ-9(V)4 CMRS
AN_BSQ-9(V) CMRS
AN_BRA-24 CMRS
AN_BQQ-10(V)4 CMRS
BLQ-10 CMRS
AN_APX-118 Cmrs
AN_USQ-172(V) CMRS
BQH-9V1 Cmrs
AN_SYQ-27 CMRS
AN_SXY-1 CMRS
AN_SSX-1 CMRS
AN_SSQ-137(V) CMRS
AN_SMQ-11D & E CMRS
AN_SSH-9 CMRS
AN_SSH-6 CMRS
AN_SPQ-9 CMRS
AN_SSW-2 CMRS

16. Questions??
Greg Hogan
DSN 873