1. KX-TDA200/100 System (Ver.2.0) Chapter 6.0 Enhanced Items
Panasonic Communications Co., Ltd.
Network Business Company
Edition Oct., 2004
Confidential 1

2. General General System Highlights New Feature & Condition
System Capacity Expansion
Software Compatibility
New Hardware
System Connection Diagram
IPGW16の説明を加える

3. System Highlights
V1.0
Networking(QSIG), Call Center, VoIP Gateway,
CTI (CSTA/TAPI), T76xx Line Up, Wireless System
V1.1
Digital XDP & Double Extension Capacity by MEC
1 Slot VoIP Gateway 4ch Card (Panasonic proprietary)
New CS to DPT Port
V2.0
IP-GW16
IP-PT Extension
Network DSS
Sending Caller ID to SLT port
External Sensor & Relay
Hotel Feature Enhancement (7 items)
LCD for VM Operation
V1.0, V1.1, V2,0のキーポイントを列挙する 永山

4. New Feature & Condition - 1
TDA0920
Features
Another condition
Highlight
Hotel
Voice Mail
CTI
16 ports IP-GW(CO) card
IP PT Extension
NDSS (Network Direct Station Selection)
Caller ID to SLT (Analogue Extension)
External Sensor
External Relay
Wake up Call Set with Voice Guidance (KX-TVA/TVM)
Voice Message Delete when Check Out(KX-TVA/TVM)
Check in / Check out Control
Telephone Charge Print Out when Check out
Remote Wake up Call Set
SMDR for External Hotel Application
SMDR(Programmable) for External Hotel Application
LCD for VM Operation (KX-TVA/TVM)
VM Message Number Display on LCD(KX-TVA/TVM)
CTI Enhancement
PC Phone / PC Console Improvement - DDI Name
PC Phone / PC Console Improvement - Copy from Outlook (International Code)
Behavior of ICD-G Key & ICM key with CTI including PC Phone / PC Console O
IP-EXT16 Card, PT(KX-NT136)
EXT-CID Card, SLT8
EIO4, OPB3
KX-TVM
6line_PT
MEC
KX-T76xx w/ LCD, KX-TVM
6line_PT, KX-TVM

5. New Feature & Condition - 2
TDA0920
Features
Another condition
Making Calls
Receiving Calls
Hold / FWD / TR
Others
TRS by Dial Time out
Speed Dial Name Reference for Public Call through Private Network
Incoming Call Log for Public Call through Private Network
CLIP when Transfer
System Speed Dial Memory Expansion
Personal(Station) Speed Dial Memory Expansion
Analogue CO line monitor
20 Pause for 2nd Dial Code
Walking Extension for Virtual Extension (For "Hot Disking" Use)
Dummy Extension of PBX for CO Telephone Number
SMDR 24H Format
SMDR Caller ID Modification
Outgoing message (OGM) recording duration expansion
MEC

6. System Capacity Expansion
Without MEC (TDA0105), no change on system capacity made.
With MEC (TDA0105), following item’s capacities are expanded.
Without MEC (TDA0105)
With MEC (TDA0105)
1.Number of Ports
(Ver.1.1)
TDA100
80 (108)
144 (158)
TDA200
160 (216)
288 (316)
2.Number of Extension
(Ver.1.1)
TDA100 64
128
TDA200
128
256
3. System Speed Dial
(Ver.2.0)
TDA100
32digits, 1000 entries/System
32digits, 1000 ent./System
ent./Tenant x 8
TDA200
4. Station Speed Dial
(Ver.2.0)
TDA100
32 digits, 10 entries/EXT
32 digits, 100 entries/EXT
TDA200
* The number of extension is consisted with all type of extension including IP-PT.
Configuration of “1.Number of Ports” for TDA100
80 ports
108 ports
144 ports
158 ports
Slot1
16 Ext.
Same as left
16 Ext. + 16DXDP
DLC16
Slot2
Slot3
Slot4
16 CO
30 ch
LCOT16 E1
Slot5
MEC

7. Software Compatibility
MPR / LPR
MPR 1.0xx & 1.1xx
MPR 2.0xx
DLC/DHLC 2.005
Yes
Yes w/o TVM
DLC/DHLC 2.008
Yes
Yes
SLC 1.002
Yes
Yes w/o EXT-CID
SLC 2.002
Yes
Yes
OPB
Yes
Yes w/o EIO4 (Relay/Sensor)
OPB
Yes
Yes
IPGW4E firmware 1.0, 1.1
Yes
Yes w/o NDSS
IPGW4E firmware 1.2
Yes
Yes
MPR / PC maintenance console
バージョンの情報は絶対に再確認すること
Installation
MPR 1.0xx & 1.1xx
MPR 2.0xx
1.07
Yes No
2.0 No
Yes
Yes
Yes

8. New Hardware – Option Card
EIO4
TDA200 4
TDA100 2
4-port external input/output card.
To be mounted on the OPB3 card (TDA0190).
(External Input/Output)
KX-TDA0164
EXT-CID
TDA200 8
TDA100 4
Sends Caller ID signals to extension ports.
To be mounted on the SLC8 card (TDA0173).
(Extension Caller ID)
KX-TDA0168
IP-EXT16
TDA200 8
TDA100 4
16-channel VoIP extension card.
Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods.
(16ch VoIP Extension)
KX-TDA0470
IP-GW16
TDA200 4
TDA100 2
16-channel VoIP gateway card.
Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods.
(16ch VoIP Gateway)
KX-TDA0490
Upgrade SD
新規追加のハードウェアのリストを出す
16 ports IP-GW(CO) card
16. External Sensor
17.External Relay
それとIP-PT（簡単に紹介）
各ハードがどのようなアプリケーションに関連しているのか簡単にコメントすること 永山
TDA200 1
TDA100 1
Optional SD Memory Card to upgrade the Hybrid IP-PBX with software version 1 or 1.1 to version 2.0,
And it adds NDSS feature and CTI enhancement, too.
(Upgrade to enhanced V2.0)
KX-TDA0920

9. New Hardware – Peripheral - 1
KX-NT136 (IP-PT)
Connection via IP
User Interface is same as T7636.
Almost of KX-T7636 Functions is in it.
PC-Phone/Console doesn’t work with.
PC Maintenance Console doesn’t connect.
Navigation Key
Dual color 24 Flexible Keys
Visible Large Ring/Msg Lamp
6 Lines 24 digits LCD /w backlit
RJ45
RJ11
TDA
LAN PC
Benefit
Remote Office, Easy moving in network, Cost saving

10. New Hardware – Peripheral - 2
TVM Series (New Voice Processing System)
TVM200
TVM50
Connection to PBX
Max. channel
Max. mailbox
Recording media
Recording time
Programming I/F
TVP200
TVP50
DPT/SLT port
DPT/APT/SLT port
6ports(12ch)
2ports (2ch)
1024
32 mailboxes
HDD
Flash
32h 6h
Hyper Terminal
RS232C, Modem
RS232C
VM-Link, DPT/SLT
12ports (24ch)
6ports (6ch) 64
128h 8h
PC Soft
USB, LAN, Modem
TVM50
All function of TVP series and New features listed below.
- VM operation with LCD (T7636, T7633 or T7630 is required.)
- Message notification by LCD message (6 lines LCD is required.)
- Wake-up call set with voice guidance for Hotel application
- Voice message delete when check-out for Hotel application (6 lines LCD is required.)
TVM200

11. System Connection Diagram - 1
IP Connection PC
IP-PT
External Sensor/ External Relay Device
Remote PC PC
Trunk (Telephone Company Lines)
Analogue / BRI / PRI / T1 / E1
Private
IP Network
Router
Server PC PC PC
Batteries
SLT
DPT
APT
DSS
DPT
DSS
PC or Printer
T7633/36 PC
USB
T7600 DPT
DXDP
Doorphone & Door Opener
SLT CS
Wireless
Phone PS
BGM/MOH
Pager/
Speaker
Amplifier
FAX
ISDN
Telephone
Voice　Processing
System
Peripheral Connection
Legacy Connection

12. System Connection Diagram – 2PC
T7600 DPT
DPT
DSS
PT-IF CS PS
Voice
Processing
System
SLT
FAX
APT
Wireless
Phone
Same capability of DLC CS
LAN
Server PC
Doorphone & Door Opener
Pager/Speaker
Amplifier
Radio
DLC16 (TDA0172)
DLC8 (TDA0171)
DHLC8 (TDA0170)
MSLC16 (TDA0175)
SLC16 (TDA0174)
SLC8 (TDA0173)
CSIF4 (TDA0143)
CSIF8 (TDA0144)
CTI-LINK (TDA0410)
OPB3 (TDA0190)
DPH4 (TDA0161)
DPH2 (TDA0162)
ECHO16 (TDA0166)
MSG4 (TDA0191)
LCOT4 (TDA0183)
LCOT16 (TDA0181)
LCOT8 (TDA0180)
CID/PAY8 (TDA0189)
CID8 (TDA0193)
DID8 (TDA0182)
E&M8 (TDA0184)
BRI4 (TDA0284)
BRI8 (TDA0288)
PRI30 (TDA0290CE/CJ)
PRI23 (TDA0290)
T1 (TDA0187)
E1 (TDA0188)
IP-GW4 (TDA0480)
IP-GW4E (TDA0484)
MPR
MEC (TDA0105)
RMT (TDA0196)
PSU-S/M/L
TDA0108/0104/0103
Router
Batteries
SMDR PC
PSTN
Analogue
E&M
ISDN BRI
ISDN PRI T1 E1
Private
IP Network
EXT-CID (TDA0168)
IP-EXT16 (TDA0470)
LAN
IP-PT PC
IP-GW16 (TDA0490)
EIO4 (TDA0164)
External Sensor / External Relay Device

13. Function – Highlight
Function - Highlight

14. 16 ports IP-GW Card - 1 - model number is KX-TDA0490.
- 16ch IPGW Card occupies a Single slot in TDA100/200 Physical I/F single Ethernet 10/100BaseT (auto sense) LED’s - Status, Link, Data, Online, Alarm & Busy
- G729a/G723.1/G711
- T.38 (FAX) mode is not supported (FAX = G711)
- Configuration using Web browser (English)
- 100% call compatibility with TDA0484/3480
- Interoperability with TDA0480
Incoming call, Outgoing call and CLIP only.
- Interoperability with another manufacturers :
Not guaranteed.
- Power factor is 0.

15. 16 ports IP-GW Card - 2 Compatibility
The compatibility of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Compatibility
TDA0480
TDA0484/TDA3480
TDA0490
Signalling
H.323 V2
QSIG service
Proprietary
H.323 V4 Annex M1
Max networked IPGW’s
511
Voice Codec
G.723/G.729a
G.711/G.723.1/G.729a
FAX Protocol
T.38
G.711
Echo canceller
16ms
48/128ms
AGC
Yes No
DTMF Tone Detection
SNMP
Event Notice by
DHCP
Yes (Client)
NAT

16. 16 ports IP-GW Card - 3 Interoperability
The interoperability of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Function
TDA0480
connected to
TDA0384/TDA0484/TDA0490
Connected to
CLIP OK
COLP No
COLR
CNIP
CNIR
CONP
CONR
CT(Avoid Tromboneing)
CF(Avoid Tromboneing)
CCBS
Making/Receiving Call
Fax Connection

17. IP PT Extension (Benefit 1)
What is benefit of IP Extension
Two type wirings require two types of construction, maintenance and their time.
One type wiring save them.
Router
LAN
Router
LAN
IP-PT
Unified wiring give low cost construction and maintenance.

18. IP PT Extension (Benefit 2)
What is benefit of IP Extension
Normal Extension
IP Extension
Slot:301 Port:02
Slot:201 Port:01
LAN
Setting change will be required.
Just MOVE
EXT.201
EXT.201?
EXT.201
EXT.201
MOVE
IP-PT
IP-PT
Setting change is not necessary Easy & Quick move enable

19. IP PT Extension (Benefit 3)
What is benefit of IP Extension
Leased
Line
PBX
Branch Office
Head Office
Router
IP Network
Private
IP-PT
PBX
LAN
Head Office
Branch Office
PBX is not necessary for Branch Office. All setting can be controlled by Head Office.

20. IP PT –1 (Sample Configuration)
Sample of configuration
Feature of IP PT(KX-NT136) is basically same as KX-T7636.
Except: OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension
Head Office
Branch Office
Private
IP Network
IP-PT
IP-EXT16
LAN
IP-PT
Secondary Ethernet Port
IP-PT 大石
3. IP PT Extension benefitと制限事項をきちんと記述する
(DHCP Server) PC
Primary Ethernet Port

21. IP PT –2 (Requirements) Requirements
- IP-EXT16 card is required.
-DHCP (Dynamic Host Configuration Protocol) Server is not supported by IP-EXT16 card.
You need to assign IP address of IP-EXT16 card by manual.
- Cable: 100 BASE-TX Category 5 or higher
- Power source: Power-over-Ethernet (PoE)
or KX-A237 AC Adaptor is necessary
Note: Following features are not supported.
OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension
IP-PT cannot be used for initial set-up of PBX system.

22. IP PT –3 (Programming IP-EXT. Card)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card by manual
Assign IP Address for IP-PT
Register IP-PT
IP Address & Subnet mask
(GW Address for IP-PT)
* If necessary (See page IP-PT7)
1. Configuration
1. Slot
2. System
14. IP Extension Setting
IP-EXT16
Property

23. IP PT –4 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
At start up
2. Press “Enter” key at 1st installation or
1. Power on IP-PT
3. Select “Network”
2. Press “Set-up” soft key from 2nd time
LCD status
2. At 1st installation
Menu
Please first setup !
OK [ENTER]
3. Menu select
1. Start up
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
操作がわかりやすい絵とか写真とか考えて欲しい9/9
IPL Start…
Now Loading
2. From 2nd time
Searching…
Setup

24. IP PT –5 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
With DHCP Server
(Automatic Assignment: IP Address for Subnet mask, IP-PT Default GW)
6. Assign IP Address for IP-EXT16 card
4. DHCP: Enable
5. Select “PBX”
7. Store
LCD status 4. 5. 6.
DHCP
Enable
IP Address
Subnet Mask
NEXT
Disable
EXIT
ENTER
矢印を太くしたほうがいい？
LCD表示と操作の関連がぱっと見てわかるようにならないか?
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
PBX IP Address ?
EXIT
CLER
ENTER

25. IP PT –6 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Without DHCP Server
4. DHCP: Disable
5. Select “IP-Address”
6. Assign IP Address for IP-PT
8. Assign IP Address for Subnet mask
7. Select “Subnet mask”
* 9. Select “Default GW”
*10. Assign IP Address for Default GW
12. Assign IP Address for IP-EXT16 card
11. Select “PBX”
13. Store
LCD status
4. – 8.
11.
12.
DHCP
Enable
IP Address
Subnet Mask
NEXT
Disable
EXIT
ENTER
操作と画面の関連がぱっとわかるようにならないか？
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
PBX IP Address ?
EXIT
CLER
ENTER

26. IP PT –7 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Without DHCP Server
Head Office
Branch Office
Router
Router
Private
IP Network
Gateway:
Gateway:
IP-EXT16
IP-PT
IP-PTからする設定でいやらしいGATEWAYの設定があったはずby Mr.Take
LAN
DHCP
Enable
Default Gateway
PREV
Disable
EXIT
ENTER
IP-PT PC

27. IP PT –8 (Register IP-PT to PBX)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Select: ON
Registration
Registration:Start
UNREGISTERED TO SERVER
OK[ENTER]
LCD of IP-PT is changed to normal
アブノーマルな状態(登録前の状態)のLCD表示も追加すること
30 SEP. 11:09AM FRI
PROG
INFO
RING
MENU
1. Configuration
15. IP-Extension Port
Confirm: OK

28. IP PT –9 Virtual LAN VLAN(L2 Switch) Necessary Information
VLAN Name : Sales
ID : 1
Port on VLAN: 1-4
Tagged VLAN: Null
PHY. Port
VLAN No
VLAN(L2 Switch)
Necessary
Information
Local Office
Remote Office
IP-PT EXT.101
IP-PT EXT.102
IP-PT EXT.103
IP-PT EXT.104
IP-PT IP Address
Subnet Mask Address
Default Gateway Address
Card IP Address
VLAN ID 1
VLAN ID is necessary for IP-PT and VLAN(L2 Switch)

29. IP PT –10 Virtual LAN Branch Office Head Office Private IP Network
Router
L2 switch configuration
VLAN Name : Sales
ID : 1
Port on VLAN: 1-4
Tagged VLAN: Null
PHY. Port
VLAN No
L2 Switch
Gateway:
Gateway:
IP Network
Private
Branch Office
Head Office
VLAN ID = 1
VLAN ID = 1
IP-EXT16
LAN
VLAN ID = 1
VLAN ID = 1
IP-PT
IP-PT
VLAN ID = 1
LCD status
VLAN ID = 1
VLAN ID って何?設計者に竹さんが確認。思うではなく事実を確認。
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
VLAN
Enable
Primary port
Secondary port (TO PC)
Disable
EXIT
ENTER
Primary port
VLAN ID
VLAN Priority 1 7

30. NDSS (Network Direct Station Selection)
TDA0920
is required.
NDSS is a DSS key referring to an extension of other PBX
It works with both of the open numbering and the closed numbering.
It’s used for monitoring extension status and making or transferring calls.
Only one TDA can be a Monitor PBX
Maximum 32 extensions in the network can be monitored.
Any extension of Monitor TDA can have NDSS.(Network Operator)
Both of Monitor PBX and Monitored PBX require KX-TDA0920
QSIG, VoIP
303
302
304
Network
Monitor
PBX
Monitored
Idle
Busy
Idle
Off =
302
Busy, DND (trunk)
Red On =
303
KX-TDA0920
Mandatory
304
To call to extension
Push = 永山
1.Network BLF(DSS)　benefitをしっかりと訴求しなければHighlightに持ってきた意味が無い。
KX-TDA0920
Mandatory
Network Operator
Benefit
Centralized Operator

31. NDSS – 2 Network PBX ID QSIG, VoIP Network
TDA0920
is required.
Network PBX ID
Each TDA100/200 V2.0 has Network PBX ID.
ID=1
ID=2-8
ID=0 (default)
Monitor PBX
Monitored PBX
Normal PBX 1
PRG
* Refer
Monitored Ext
ID=2
ID=3
ID=4
QSIG, VoIP
Network
ID: none Other PBX
Before V2.0, TDA30, TD500
ID=0
ID: 2-8 Monitored PBX
Each ID must be unique in the network.
V2.0 or later
ID: 1 Monitor PBX
Only one in the network.
V2.0 or later 永山
ID=1
Network Operator
ID: 0 (default) Normal PBX
It’s neither a monitor PBX nor a Monitored PBX.
Some PBXs transmit status information of Monitored Ext.
V2.0 or later

32. NDSS – 3 Status Information Routing
TDA0920
is required.
ID=3
IPGW at slot1
IPGW at slot3
IPGW at slot6
Network Operator = 102
IPGW Card Slot to send out = slot3
Status Info. IP Routing Table
402 Busy
Case : VoIP Q-SIG 3
PRG
* Refer
Status Information Routing
Transmitting route for Status Information data
must be constructed.
Case : ISDN (PRI, BRI) Q-SIG
Network Data Transfer
Yes (ON) : Send
No (OFF) : Receive
* Q-SIG port base setting ON
OFF 5
PRG
* Refer
NDSS data Transfer
VoIP ISDN : Enable 2
PRG
* Refer
Monitored Ext
ID=3
102
ID=1
Network Operators
ID=2
ID=0 ON
OFF
101
103
ISDN Q-SIG
IP Network
VoIP Q-SIG
302
402
Idle Busy
402 Busy
402 Busy 永山
Idle Busy
302 Busy
302 Busy

33. NDSS – 4 Network Monitor Extensions Table QSIG, VoIP Network
TDA0920
is required.
Network Monitor Extensions Table
Monitored Ext
ID=3
102
ID=1
Network Operators
ID=2
101
302
402
QSIG, VoIP
Network 4
PRG
* Refer
Monitor Extensions Table
No.
001
002
003
032
Ext. Name for reference
302
Network PBX ID 2 3
402
Max. 32 Ext.
* Only for a monitor PBX
Starting monitoring & Stopping monitoring
All NDSS start monitoring.
* Any extension can do.
NDSS
To start monitoring * 7 4 8
C.Tone #
Network Ext. No.
NDSS or
To stop monitoring
* Only a manager extension can do.

34. Updating Firmware of IP-GW4E
NDSS – 5
TDA0920
is required.
Conditions
TDA0920 must be in both of monitor PBX and monitored PBX.
The firmware (not LPR) of IP-GW4E(TDA0484) must be Version1.2 or later.
Network PBX ID:1-8 must be unique in the network.
It’s possible to stop monitoring at monitored PBX by PC Maintenance Console.
NDSS does not work on PC-Phone / PC-Console.
You can not back up all of NDSS configuration into DSYS.
( * You need to check and re-configure some part of NDSS after initialize reset, even you have DSYS as backup. )
Updating Firmware of IP-GW4E
(1) Connect a browser to IP-GW4E. ( Updating is done through a browser. It’s not from PC Maintenance Console.)
(2) Login to IP-GW4E with the name: Installer, PW: Installer.
(3) Change the status of the card from “RUN” to “STOP”.
(4) Now, you can upload a firmware and update the card with the procedure in the manual (3.3 Data Management).

35. NDSS – 6 Programming Instruction - 1 1 PRG Network PBX ID Assignment 2
TDA0920
is required.
Programming Instruction - 1 1
PRG
Network PBX ID Assignment 2
PRG
NDSS data transfer
VoIP  ISDN
Only when ID = 2 - 8
ISDN  VoIP
Only when ID = 1
* The PBX(ID=0) can’t perform this direction.
How many time NDSS data can be transferred
Frequency of NDSS data from IPGW or PRI card 3
PRG
Status Info. Routing Table
Any extension number which is reachable from this monitor PBX
A slot number of IPGW card which the data is sent from 4
PRG
Network Monitor Extensions Table
Up to 32

36. NDSS – 7 Programming Instruction - 2
TDA0920
is required.
Programming Instruction - 2
Data transmitting direction over Q-SIG
Case : ISDN (PRI, BRI) Q-SIG ON
OFF 5
PRG
Network Data Transfer
Yes (ON) : Send
No (OFF) : Receive
* Q-SIG port base setting

37. Caller ID to SLT - 1 PSTN Benefit
Caller ID from SLC port to Normal Telephone, Cordless Telephone, FAX machine,etc.
FSK (ETSI and Bellcore) signaling only
16 digits maximum
Adding Trunk Access Number for calling back Purpose (Programmable)
TDA0173 (SLC8) and TDA0168 (EXT-CID) are required.
For Calling back (Programmable)
Max. 16 digits
PSTN
(0, 9) +
Caller ID :
SLC8
EXT-CID
FSK, DTMF, others
Only FSK
(0,9)
302
302 永山
18. Caller ID to SLT(Analogue Extension)
(18)
Caller ID to SLT (Analogue Extension)
Extension Caller ID card on SLC8 card is needed for KX-TDA100/200.
One Extension Caller ID card support 8 ports.
Support FSK type. (Not support DTMF type.)
Software version up of SLC8 card (LPR) is required if Extension Caller ID feature is required.
302
Benefit
Recognizing caller, easy calling back

38. Caller ID to SLT - 2 Action in Unscreened transfer operation TR
Receiving a call
Answer and transfer
On Hook
302
CID: TR
SLT stops ringing
and rings again
302
Condition
- CID is between 1st bell and 2nd bell
- Incoming Call Log Information is not shown on the SLT.
- TDA0168(EXT-CID) must be installed on TDA0173(SLC8).
- LPR software of TDA0173 (SLC8) must be or later.
- One EXT-CID supports 8 ports. (All ports of SLC8 which has EXT-CID on it can send out CID.)
- EXT-CID can be installed onto all off SLC8s in a TDA system.
Screened Transferの時の動作も書いたほうがいい

39. Caller ID to SLT – 3 Programming items - 1 Adjusting interval: 0-15
Enable sending CID to Ext.: Enable/Disable
Adding Trunk Access Number: Enable/Disable

40. Caller ID to SLT - 4 Programming items - 2 CID Modification table
- modified CID will be sent to SLT port
SLC8
Property
Check if EXT-CID is installed

41. Caller ID to SLT – 5
Priority of items displayed when TDA is receiving FSK CID
FSK CID may bring information such as private, out of area or long distance.
If TDA received
Result
priority
high
low
“private” or “out of area”
“private” or “out of area” is displayed.
“long distance”
“long distance” is displayed.
Another items
Caller ID and Name is displayed.

42. External Sensor - 1
If a device connected to the external sensor becomes active, there are 3 outcomes:
(1)Sensor call will be generated to the pre-programmed extension
(2)Generates SMDR Printout
(3)Generates 3rd Party CTI command
The sensor call destination can be a PT, SLT,PS, or ISDN extension but not an ICD-Group.
- If a sensor call arrives at an extension
Display : pre-assigned name of sensor port [5.5]
Ring : Distinctive ringer pattern can be assigned (triple, or special double ring, so on) [2.8.3]
- Special Tone(Dial Tone 3) will be sent to answering extension.
- If nobody answer sensor call, sensor call stops with pre-programmed time [2.4.3].

43. External Sensor - 2 Timings
The External Sensor has some timing parameters that can be set using the maintenance console [1.] and clicking on the OPB3 card.
Input Signal Decision Time = This is the time delay before Extension begins to Ring.
Input Signal Detection Reopening Time = This is the time it takes the sensor to reset hence the time it will take to respond to the next input.

44. External Sensor - 3 Connection Diagram
Power to the external sensor is provided from the EI04 card and must be grounded through the EI04 card as indicated in the diagram below. A pair of “sensor” and “common” lines are connected to the EI04 card for each external sensor. The TDA detects inputs from the sensor when the signal is under 100 Ohms.

45. External Relay
Extensions can activate external relay for controlling external devices(On/Off) by feature code. There is a COS that has to be programmed to enable this feature.
It is possible to activate the relay for pre-programmed time [5.4].
The relay is the relay normally open.
And has a maximum switching voltage of : 24VDC(1A)
30VAC(1A)

46. Function - Hotel Function – Hotel 大石
7 Wake up Call Set with Voice Guidance (KX-TVA/TVM) Hotel Feature
8 Voice Message Delete when Check Out(KX-TVA/TVM) Hotel Feature
9 Check in / Check out Control Hotel Feature
10 Telephone Charge Print Out when Check out Hotel Feature
11 Remote Wake up Call Set Hotel Feature
12 SMDR for External Hotel Application Hotel Feature
13 SMDR(Programmable) for External Hotel Application Hotel Feature

47. Hotel - 1 - Wake up Call Set with Voice Guidance (KX-TVA/TVM)
- Voice Message Delete at Check Out, Automatically(KX-TVA/TVM)
6 Line LCD PT for Hotel Operator
- Check in / Check out Control
- Telephone Charge Print Out when Check out
“Wake up call is set at 07:30.”
KX-TDA200 or TDA100
Remote Wake up Call Set 大石
7 Wake up Call Set with Voice Guidance (KX-TVA/TVM) Hotel Feature
8 Voice Message Delete when Check Out(KX-TVA/TVM) Hotel Feature
9 Check in / Check out Control Hotel Feature
10 Telephone Charge Print Out when Check out Hotel Feature
11 Remote Wake up Call Set Hotel Feature
12 SMDR for External Hotel Application Hotel Feature
13 SMDR(Programmable) for External Hotel Application Hotel Feature
- SMDR for External Hotel Application
Programmable SMDR
KX-TVA200 or TVM200
for External Hotel Application
KX-T7636

48. Hotel - 2 Operation Assignment Check in Hotel Operator EXT.
Check in button
Check in + Room No. (EXT. No.)
Remote Wake up Call set
Dial *76*1 + Room No. + Time
Check out
Automatic voice message delete
*Check out button
Automatic telephone charge print out
*Header / Footer
Check out + Room No. (EXT. No.) + Print / YES
*Check in / Check out
*Charge: Margin/Tax
*Telephone / Minibar / Others
*Telephone margin
*TAX rate: telephone /minibar/others
*Timed reminder Start / Answer / No response
*Select print item
*Programmed message

49. Hotel - 3 (Check In) - Check in / Check out Control
6 Line LCD PT for Hotel Operator
Check-in:
On hook status
Check-in button
Enter
Dial EXT.No. or DSS
Enter
Check-out:
On hook status
Check-out button
Enter
Dial EXT.No. or DSS

50. Hotel - 4 (Wake up Call / Check Out)
Remote Wake up Call Set
Dial * 7 6 *
1: Set
0: Cancel or
Off hook status
EXT. No. or DSS
Hour: Minute (+ 0: AM 1:PM by 12H)
0: Once
1: Dairy
- Telephone Charge Print Out when Check out
Check-out:
On hook status
Check-out button
Enter
Dial EXT.No. or DSS
PRINT NEXT YES (Soft Key)
Enter “Minibar” and “Others”
Room:103
Telephone:
Minibar :
Others :
EXIT
NEXT
PRINT
Confirm check out ? NO
YES
Enter Room Number
ENTER
LCD status

51. Hotel - 5 (SMDR Setting) - SMDR for External Hotel Application
Check in/out
Timed Reminder Start/Answer/No Response
Programmable SMDR
for External Hotel Application
Printing Message (on SMDR) can be assigned.
Dial *761
Printing Message No. #

52. Hotel - 6 (Billing Sheet)
Sample of Call Billing Sheet

53. Hotel - 7 (Rate Calculation)
Margin/Tax Rate Assignment
[Calculation Method]
[Meter indication received from telephone company] x [Call Charge Rate]
[1 - Tax Rate] x [1 - Margin Rate]
Pay tone: Analog trunk + pay tone card
Meter Pulse: E1 line
[Charge received from telephone company]
[1 - Tax Rate] x [1 - Margin Rate]
Advice of Charge: ISDN

54. Function – Voice Mail Function – Voice Mail 永山
5 LCD for VM Operation (KX-TVA/TVM)
6 VM Message Number Display on LCD(KX-TVA/TVM)
(5)
LCD for VM Operation (KX-TVA/TVM)
PT has to be KX-T7636/T7633/T7630.
LCD data for VM will be provided by CD-ROM packed in KX-TVA/TVM.
Max.5 language's LCD data for VM should be copied to SD card of KX-TDA.
<TDA100/200>
MEC card is not required for KX-TDA100/200.
<TDA30>
MEC card is required for KX-TDA30/50 if two or more language's LCD data of for VM is required.
If MEC card is not installed, only one language (English or other) is available.
(6)
VM Message Number Display on LCD (KX-TVA/TVM)
PT has to be 6 line LCD type.
If the PT extension has 3 new messages in mail box of TVA/TVM,
"Voice Message : 3" will be displayed instead of "Message Waiting".

55. LCD for VM Operation - 1 (Receive a Message)
The screen shots show how easy it is to Receive a Voice mail message with the new KX-TVM series.
Main Menu
Deliver Msg.
A.A. Status
Check Distribution
EXIT
Receive Msg.
Condition
PT must be T76xx with LCD.
Max.5 Language’s
3 messages
MBX 203 AUG24 11:04AM!
AUG24 09:23AM
EXIT ERASE PLAY
ROBINE2 AUG24 03:47PM!
SHIFT EXIT ERASE STOP
ROBINE SCHNEIDER
MBX 120
AUG24 03:47PM
NEW 00:03:12
****------

56. LCD for VM Operation - 2 (A.A Status)
The screen shots show how easy it is to change the automated attendant settings with the new KX-TVM series.
Main Menu
Deliver Msg.
Check Distribution
EXIT
Receive Msg.
A.A. Status
A.A. Status
Covering Extn.
Mbx. Retention Mode
EXIT
Call Transfer
Incomplete Handling
EXIT DALL
Call Transfer Status
Enable Screening
Disable Int. Paging
Disable Beeper
Disable Blocking

57. Voice Mail Message Number display on LCD
The number of new messages can be indicated on the LCD of PT.
This feature is supported on TVM series voice mail.
Condition
- PT with 6 line LCD
26 JUL. 10:20AM MON
Incoming Call :001
Voice Message :002
PROG INFO RING MENU

58. Function - CTI Function – CTI 永山 2 CTI Enhancement
41 PC Phone / PC Console Improvement - DDI Name
42 PC Phone / PC Console Improvement - Copy from Outlook (International Code)
43 ICD Group Key (Group DN Key) for CTI including PC Phone / PC Console
(2)
CTI Enhancement
LED control for PT (CTI button on Flexible Key)
LCD control for PS
And so on
SD card (KX-TDA0920) is required.
We are preparing detailed specification document for software developer and sales company.
(41)
PC Phone / PC Console Improvement - DDI Name
DDI(DID) name of PBX can be displayed.
DDI(DID) name of PC has priority.
(42)
PC Phone / PC Console Improvement - Copy from Outlook (International Code)
For example, " "
will be or or by programming.
(43)
ICD Group Key (Group DN Key) for CTI including PC Phone / PC Console
Group key is not used automatically for making call from CTI.

59. CTI Enhancement New Functions Condition - KX-TDA0920 is mandatory.
is required.
New Functions
Supporting New Hardware
External Sensor, IP-PT
Controlling Ring Pattern for redirected call
Setting Extension Absent Message
Another enhancement
MIC
MWL
FCO key
SP On/Off
SP Volume
Ring On/Off
LCD Display contents PT
YES
IP-PT PS
Controlling PT
MultiPBX Loading Function
2 PBXs are controlled by TAPI.
* This does not mean
that PMS controls two PBXs.
Conditionは再確認が絶対に必要
Condition
- KX-TDA0920 is mandatory.
- TSP Built or later
- USB ports or LAN interface on PC
- Windows 2000(Pro, Server) or Windows XP(Pro)

60. PC Phone / PC Console Improvement
New Features
New Feature Enhancement for “External Sensor”
New Feature Enhancement for display the DDI Name from PBX when alerting
DDI(DID) name of PBX can be displayed.
DDI(DID) name of PC has priority.
Improvements
Import function from Outlook Phone Book(the method for International code)
For example, " "
will be or or by programming.
Screen sentences were revised to correct sentences (except English)
When “Call Pickup by DSS ICD Group Call” is disabled by programming,
the operator can not answer the call from Incoming Group screen.
Before
the operator can answer the call from Incoming Group screen.
New
when it saved without inputting to TextMemo,
Incoming/Outgoing record (Call Log) is not left in Call Log.
Before
Incoming/Outgoing record (Call Log) is left in Call Log.
New
Under using Italian language,
Before
the operator cannot attach a photo into “Pop-up” except BMP.
the operator can attach a photo into “Pop-up” with other than BMP format, too.
New

61. Function - Making Calls大石
22 Speed Dial Name Reference for Public Call through Private Network
35 TRS by Dial Time out

62. TRS by Dial Timeout - TRS by Dial Time out
(Inter-digit timer is working in checking TRS.)
0: Call PTT Operator in North America
RESTRICT
00: Credit Call
NO RESTRICTION
Example 1: Operation in U.S.A.
Keep (default)
Disconnect
Activate this feature!
Example 2: Preventing escaping from TRS
Keep
Disconnect
FWD to 9
CO-CO call
No DTMF-R in trunk cards
DTMF dialing can go thru. (No check)
But TDA disconnects by the timer.
PSTN
dials
Restriction table
99restrict
TRS判定中のTIMEOUTはDISCONNECT
これにより、FWDtoCOで‘9‘一桁にFWD設定して、CO-CO呼を作ることによる発信規制逃れも防止できる
上記をプレゼンに盛り込むこと

63. Function - Receiving Calls永山
20 Incoming Call Log for Public Call through Private Network
21 Caller ID to SLT for Public Call through Private Network
31 CLIP when Transfer
39 Visual Caller ID improvement
(20)
Incoming Call Log for Public Call through Private Network
If the number of caller ID digit of call from private network is 9 (default) or more than 9, the call is logged as public call.
Please see sheet4.
(21)
Caller ID to SLT for Public Call through Private Network
If the number of caller ID digit of call from private network is 9 (default) or more than 9 and the destination is SLT port with caller ID service, the caller ID is sent to SLT as public call.
(31)
CLIP when Transfer
CLIP of held CO party or CLIP of extension who is transferring can be programmed as CLIP to send to CO.
Default is extension.
CLIP when Forwarding is not included for this improvement.
(39)
Visual Caller ID Improvement Version 2.0 Plus
Visual Caller ID (Call Waiting Caller ID service by Telephone Company - Analog CO) feature will be improved.
Specification is same as KX-TDA30 version 1.1 Plus.

64. Speed Dial Name Reference through Network
Panasonic
Telecom Line
Private Network
If Caller ID is matched to the number in System/Personal Speed Dial, the correspond name can be displayed on LCD. It is effective through Network, too.
Panasonic
6. Feature
1. Speed Dialing & Caller ID
1. Main Table

65. Incoming Call Log for Public Call through Private Network
TDA distinguishes incoming calls from the private network between private call and public call.
CID:
Public Call
CID:
CID:
10 digits > 9
Public Call
CID:
CID:
6 digits =< 9
Private Call
Incoming Call
Logging
Public
Network
PBX code
952
Private
Network
Threshold Value
= 9
Ext.101
Threshold value: 0-15 (default:9)
Priority condition
Call Type Info.
From other PBX
Digits Comparison
With threshold
Public
Private
Don’t Care
Over
Under or equal
Result
TDA V2.0 can send correct call type.
TDA V1.0, V1.1 send “Private Call” as call type. *

66. Function – Hold/Forward/Transfer
該当項目無し、多分この章は削除

67. CLIP when Transfer
CLIP to be sent to CO when transferring (to CO) has following choices.
send CID which is sent in usual of the extension’s making a call
send CID of held CO party
* This configuration does not apply for Call Forwarding.
CLIP in forwarding is received CID.
Disable (default): send CID of EXT
Enable : send CID of Held CO Party

68. Function - Others Function – Others 19-30は大石、残りは永山 ロシア・東欧の言語対応はまとめるべき？
14 Personal(Station) Speed Dial Memory Expansion
15 System Speed Dial Memory Expansion
19 Analogue CO line monitor
23 20 Pause for 2nd Dial Code
24 Telephone book (PT) - Cyrillic / English Searching
25 Telephone book (PT) - Greek / English Searching
26 Telephone book (PT) - Searching by Ukrainian and Belarusian
27 Telephone book (PT/PS) - Cyrillic / English Independent Sorting Order
28 Telephone book (PT/PS) - Fix problem of sorting for Capital Letter / Small Letter
29 Walking Extension for Virtual Extension (For "Hot Disking" Use)
30 Dummy Extension of PBX for CO Telephone Number
32 SMDR 24H Format
SMDR Caller ID Modification
No limitation for Recording Duration for MSG card
LCD for Latvia
45 PT System Programming LCD for Ukraine

69. Others - 1 - Memory Expansion MEC Each Tenant has a choice.
System Speed Dial
TDA100
32digits,
1000 entries/System
32digits,
1000 ent./System ent./Tenant x 8
MEC
TDA200
Each Tenant has a choice.
- to use a list for system
- to use a list for tenant
Station Speed Dial
(Personal Speed Dial)
TDA100
32 digits,
10 entries/EXT (01-09)
32 digits,
100 entries/EXT (00-99)
MEC
TDA200
14 Personal(Station) Speed Dial Memory Expansion
15 System Speed Dial Memory Expansion
Original 10 entries aren’t copied to first 10 entries in 100 entries.

70. Others - 2 - Analog CO Line Monitor
Detection of physical line disconnection
If CO line is disconnected physically, the CO port become Out of Service Automatically.
Except AL/NE model LCOT card by difference of hardware
- 20 Pauses for 2nd Dial Code
V1.1 = Max. 4 Pauses, V2.0 = Max. 20 Pauses

71. Others - 3 - Working Extension for Virtual Extension
V1.0= SLC16 without phone
V1.1= DLC16 temporary use only
- Dummy Extension of PBX for CO Tel. No.
PBX recognize CO Tel. No. as EXT. No.
You can use mobile phone like as extension.
TDA100/200: Max 128 PS or Mobile phone
TDA30: Max 28 PS or Mobile phone

72. Others - 4 - SMDR Enhancement Time stump in 24h format
 Default of NE
 Default of others
Caller ID Modification
- After Modification
- Before Modification
 Default of US, Canada
 Default of others
Example 1:
Default for US/Canada is "Before Modification". Default for other is "After Modification".
For example, call from through ISDN CO will be print as
by "Before Modification" mode.
by "After Modification" mode.
Example 2:
(Call from UK)
or (Call in US) by "Before Modification" mode
(Call from UK)
or (Call in US) by "After Modification" mode 永山
32 SMDR 24H Format
SMDR Caller ID Modification

73. Others - 5 - Outgoing message (OGM) recording duration expansion
V1.1 or before
V2.0
Total 8 minutes
Up to 64 messages
Max. One minute
for each message
Max. Eight minutes
34 No limitation for Recording Duration for MSG card

74. To Start TDA100/200 V2.0 To Start TDA100/200 V2.0 永山
PC Maintenance Console Compatibility
40 PC Maintenance Console Area Selection
Data Conversion
Upgrade PBX
44 MPR Software Version up by SD Card Exchange

75. PC Maintenance Console Compatibility
Initial Screen
Automatically
V1.1 is connected.
V2.0 is connected.
Automatically
V1.0 is connected.
Two versions are installed into a PC.
V2.0
V1.07

76. PC Maintenance Console Installation - 1
PCC provides two installers.
pcprogv2000R5.exe
pcprogv107cR3.exe
(V2.0)
(V1.07)
Only for TDA V2.0
For TDA V1.1 & V1.0
The Installation order is important.
Installation without uninstalling 1st install.
Possible programming
1st
install
2nd
install
TDA
V1.0
V1.1
TDA
V2.0
TDA
Case1:
V1.07 +
V2.0
Result
OK !
Yes
Yes
Yes
Case2:
V2.0 +
V1.07
No good !
Yes
Yes No
You need UNINSTALL V1.07 and V2.0 and install again in correct order.
* You can uninstall both of V1.07 and V2.0 at once in normal uninstall operation.
Case3:
V2.0
None No No
Yes
Case4:
V1.07
None
Yes
Yes No

77. PC Maintenance Console Installation – 2
Area Selection Difference
V1.07
V2.0
“Please select suffix code.”
“Please enter your country code …”

78. Data Conversion 1. Back up DSYS (V1.0 or V1.1) to PC
1-1 “Tool” => “SD Memory Backup”
1-2 “Utility” => “File Transfer PBX (SD Card) to PC”
1. Back up DSYS (V1.0 or V1.1) to PC
2. Update DSYS to V2.0 by PC Maintenance Console V2.0
2-1 Open DSYS (V1.1 or V1.0) from PC Maintenance Console V2.0.
2-2 Following dialog appears.
No conversion, opening DSYS as it is.
Going back to initial screen.
3. Conversion Complete.
DSYS of V2.0 is saved at local PC
Caution : Converting from V1.0 requires PC Maintenance Console V1.07, too.

79. Upgrade PBX 1. Prepare following files
- PMPR 2.0, DLNG0 2.0, DLNG1 2.0
DSYS Converted DSYS or New DSYS created by PC Maintenance Console
2. Download above files to PBX
3. Reset PBX by command
- V or later --- Please select PMPR_SUB, DSYS_SUB, then reset
- Before V Please reset without any care.
Select
Select
4.Connect PC-Soft again and download other files as the dialog box saying.
5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.

80. Enhancement by Upgrade SD card - 1
1. Some features are enabled by Upgrade SD card (KX-TDA0920) .
- TDA V1.0
- TDA V1.1
- TDA V2.0 (Normal)
TDA V2.0
Enhanced
KX-TDA0920
Upgrade SD
What is an
upgrade SD ?
KX-TDA0920 + =
Normal SD
DKEY-SD
File: + =
The information in DKEY-SD is different for each SD card.
2. Enhancement procedure
From
V1.0 or V1.1
V2.0 (working)
V2.0 (brand new)
Make backup of TDA0920 into local PC
Step1
Yes
Backup current DSYS to PC
Step2
Convert DSYS to V2.0
Step3
Step4
Change SD to TDA0920,
then execute initialize reset
Send User’s DSYS to TDA
Step5
5-1 “Utility” => “File Transfer PC to PBX (SD Card)”, DSYS will be saved as DSYS_SUB.
5-2 Restart from command with following choices.
DSYS: Use Replace File
PMPR: Keep Present File
TDA V2.0 Enhanced begins to work.

81. Enhancement by Upgrade SD card - 2
3. Data Reset After Upgrade
Log
- Incoming Call Log
- Outgoing Call Log (including Last Number Redial)
- Message Waiting
- SMDR
- Advice of Charge (AOC) / Pay Tone
- ICD Group monitor log for supervisor
Group
Status
- ICD Group login status
(All extensions are set to Login by default.)
- ICD Group Ready/Not Ready status
(All extensions are set to Ready by default.)
Others
- Extension Lock/Remote Extension Lock
- Extension PIN Lock/Extension PIN Lock counter
- Verified Code PIN Lock/Verified Code PIN Lock counter
- Password Lock counter for Remote System Programming
- PBX Error Log
System
- PBX date and time
- Timed Reminder
- LPR Timed Update time
- Daily test start time
PT/Ext
Status
- PT handset/headset volume
- PT SP-PHONE volume
- PT ring volume
- PT display contrast
- Live Call Screening (LCS) On/Off
- Hands-free Answerback status
- Absent Message status of extensions
(Absent Message data itself is no cleared.)
- Fwd/DND status (FWD destinations are not cleared.)
And
PS registration information will be cleared, too.
PSの情報はもっと目立つように

82. Enhancement by Upgrade SD card - 3
4. How to go back to normal TDA
Prepare SD card of previous version. (Normal V2.0, V1.1 or V1.0)
Step1
Set the slide switch position to “Lock”, then insert to TDA.
* TDA must be turned off, at first.
Step2
Execute initialize reset of TDA
Step3
Set the slide switch position to “Un-Lock”, then insert to TDA.
* TDA must be turned off, at first.
Step4
Execute normal reset of TDA (It’s no need to send DSYS to TDA.)
TDA begins working with previous version.

83. Thank you very much ! Thank you very much ! TDA30のみで実現した下記の項目どうする?
1 Fax Automatic Routing by MSG Card (This is not applied for TDA100.)
2 Built in TAM (Pending) (This is not applied for TDA100.)