Presentation is loading. Please wait.

Presentation is loading. Please wait.

What we would like to accomplish. In order for us to move forward from a technical stand point we need to make some serious changes in the audio systems.

Similar presentations


Presentation on theme: "What we would like to accomplish. In order for us to move forward from a technical stand point we need to make some serious changes in the audio systems."— Presentation transcript:

1 What we would like to accomplish. In order for us to move forward from a technical stand point we need to make some serious changes in the audio systems in the gymatorium. In addition we need to make some changes in the way we rehearse. Presently none of the worship team gets to practice together in the gymatorium outside of doing a sound check on Sunday AM. Infrastructure We desperately need to move the amps and signal processing equipment from a non air conditioned space down to the equipment room which is air conditioned 24/7. At the same time we want to have a new patch bay installed. We want to build what we’ve named “The Ark” to move the FOH mix position down to the floor and out of the “black hole”. The Ark would be for the FOH operator and would have the board, tape decks, CD & efx unit only. From my own experience and having spoken with a consultant, for our purpose he recommended 3, 16 pair snakes to the Ark. We would use 32 pair for inputs and 16 pair for returns, auxiliaries and communications. We would also pull a 16 pair new run from the patch bay to the black hole. By using the old Yamaha board from the chapel to the black hole and installing it there we would use it for day to day operations to play tapes, CD’s and plug in a microphone without having to use the Ark. The accompanying sketches show how this would be implemented

2 Ark Signal processing, amps & patch bay To be located in equipment room. New multi-pair cable Belden 9616 x 3 (48 pair total) Black Hole New multi-pair cable Belden 9616 x 1 (16 pair total) FOH Speakers New 8-10ga speaker wire

3 EQ Crossover Amp # 1 Install a new 19”x72” standard rack and move the signal processing and amplifiers from the furnace room down to the equipment room. Install new patch bay interrupting the current inputs from the stage to the black hole. Run 48 pair (3 x 16 pair) from the equipment room to the rear wall where the Ark will be eventually located. Also run 16 pair from the same rack to the black hole. Install 6 new mic stage inputs dedicated (but patchable) for the Yamaha in the black hole. Install dual DPDT relays for switching FOH & FB1 outputs between Ark & black hole. This allows us to be able to plug any microphone into either board (Soundcraft or Yamaha) and either board can drive the signal processing, amplifiers and speakers. This will also allow us to be able to patch any signal from the Ark up to the black hole for digital recording on the worship computer and allow for any future expansions. There will be extra wiring in place for a low voltage intercom system so that the FOH operator to be able to communicate with the operators and cue director in the black hole. Inputs from Stage and other areas Links to and from the Ark Links to and from Black Hole Signal destination inputs EQ Amp # 2 Amp # 3

4 Most of the “patch’s” will remain in place from day to day. As an example only To patch #7 on the stage to #21 on the Spirit you would install a patch cable as shown with the red line To send the FOH signal from the spirit to the input of the signal processing and amplifier chain you would install a jumper as shown with the blue line. Once we “Patch Up” the changes would be minimal. What I’d like to see us do is put a switch that controls two DPDT relays in the signal input stage to switch between taking a output from the black hole or the Ark. If someone other than a tech needed to play a tape they just flip the switch and then they can use whatever we set up in the black hole for them before hand. Also I want to put an inexpensive limiter compressor on those lines so the system can be protected.

5 Inputs from stage & other areas (expandable) Top two rows (pos 1-32) are Ark inputs 1-16 & 17-32 Third row (pos 33-48) are returns, auxiliaries and communications Signal destination inputs Pos 01 – FOH (L) Pos 01 – FOH (R) Pos 03 – Aux 1 Pos 04 – Aux 2 Pos 05 – Aux 3 Pos 06 – Aux 4 Pos 07 – Aux 5 Pos 08 – Aux 6 Pos 09 – Pastor’s W/L DO to computer Pos 10 – Future use Pos 11 – Future use Pos 12 – Future use Pos 13 – Future use Pos 14 – Future use Pos 15 – Future use Pos 16 – Communications The Black Hole Pos 01 – Mic input Pos 02 – Mic input Pos 03 – Mic input Pos 04 – Mic input Pos 05 – Mic input Pos 06 – Mic input Pos 07 – NSI Lighting controller Pos 08 – Pastors WL Mic Pos 09 – Future use Pos 10 – Future use Pos 11 – Future use Pos 12 – Future use Pos 13 – Communications Pos 14 – Communications Pos 15 – FOH Out Pos 16 – Mon Out

6 Cable 1 (lines 1-16) These will be microphone inputs from stage Cable 2 (lines 17-32) These will be microphone inputs from stage Cable 3 (lines 33-48) These will be returns and communications The Ark EFX Unit Tape Playback CD Playback Tape Record Soundcraft Live 4/2-32

7 “The Ark” See www.hsarolltops.com for examples of what the Ark could look like. 48 (16x3) pair snake(s) 110 VAC @ 30 amps 2 Cat 5 Network “just in case”

8 PantryElectrical KITCHENKITCHEN Ark A A A A A B B B B B B BB B B BB B C C C C CC C C C C DD D E EE E E F FUUU U U U U U U U U Electrical Outlets by breaker SERVINGSERVING LINELINE


Download ppt "What we would like to accomplish. In order for us to move forward from a technical stand point we need to make some serious changes in the audio systems."

Similar presentations


Ads by Google