2. 1 Electrical Circuits

3. 2 Basic Electric Circuit: In a circuit, the electrons are flowing or moving. They are not stationary or static.

4. 3 Common Schematic Symbols: Conducting Wire: Switch:Light Bulb: Battery or Voltage Source: AC Voltage: Capacitor: A Ammeter: V Voltmeter:Resistor:

5. 4 Current Current describes the number of electrons flowing in a circuit. It doesn’t count the actual number of electrons, that would be too cumbersome… Current is typically measured in Amperes. (Amps for short) 1 Amp = 1 Coulomb / second. 1 Amp is a relatively large amount of current, often milliamps, mA are used. 1000mA = 1 Amp

6. 5 Voltage Sources No current will flow unless there is a voltage source. This is also known as a potential difference. Sometimes, this potential difference is supplied by batteries!

7. 6 Analogy: Imagine a rock laying on level ground. It will not move anywhere (no current) since there is no difference in elevation (voltage). However, an object at the top of a hill could roll down (current flowing) because of the elevation difference (voltage).

8. 7 Electrical Resistance In almost all circuits, the electrons flow with some opposition or resistance. Resistance is measured in units called Ohms. The symbol is the Greek letter omega: Ω Virtually any item that has electricity flowing through it has some resistance. Some items have more resistance than others

9. 8 Resistors: Often, the flow of electricity needs to be reduced or controlled. Devices called resistors are used. The resistance of a wire can depend on several things including: thickness (area) of wire temperature of wire length of wire

10. 9 Analogy: As mentioned earlier, there are many similarities between electrical circuits, and “water” circuits. http://faraday.physics.utoronto.ca/IYearLab/Intros/DCI/Flash/WaterAnalogy.html

11. 10 Ohm’s Law Mr. Ohm discovered an extremely useful relationship: V= I R Voltage = Current x Resistance Of course, this formula can be rearranged to solve for whatever is needed...

12. 11 Example: A light bulb operates on a 110 volt circuit. The bulb draws a current of.91 amps. What is the resistance of the light bulb? V=IR R=V/I R=110V/.91A 120.8 Ohms, Ω

13. 12 Quick Review: Electric potential has units of: Volts, V Resistance has units of: Ohms, Ω Current has units of: Amperes, A, Amps

14. 13 Shocking? To receive a shock, there must be a voltage difference applied to you. ( electrons must “roll” downhill) This is often referred to as a potential difference.

15. 14 A bird could sit on a high voltage wire and receive no shock at all. Its entire body is at the same high voltage. No voltage difference. However, if it touches the ground or tower, then there would be a large voltage difference, and the current would flow!!!

16. 15 To prevent electric shock, most cords have a third prong that is used to ground the cord. If there are any extra electrons, they are immediately sent to the ground, not you.

17. 16 Two Types of Current: DC, Direct Current: the charge flows in one direction only. Examples: batteries AC, Alternating Current: electrons in the circuit move in one direction, then switch and then flow in the opposite direction. Examples: wall outlets

18. 17 AC Frequency: Since AC current changes direction, or oscillates, you can describe how often it changes direction. Almost all US outlets use a frequency of 60 Hz.

19. 18 Adapters: Often it is useful to convert AC into DC, or vice versa. To save batteries, you’ve probably plugged a radio or CD player into the AC wall outlet.

20. 19 Notice the input/output voltages, and frequency. Diodes allow electrons to flow in one direction only. They help change AC into DC.

21. 20 Speedy Electrons? When you complete electric circuits, the information or impulses travel at nearly the speed of light! However, the electrons themselves don’t travel nearly that fast. It’s actually the electric field that travels that quickly. The electrons continuously bump into atoms in the conducting metal. These collisions are what cause a wire to get hot when a lot of current is flowing.

22. 21 Electric Power: Just like mechanical power, electrical power describes work done per unit of time: 1 Watt = 1 Joule / 1 second 1000 Watts = 1 kilowatt In terms of electrical quantities, power can be calculated by multiplying current x voltage. P = I V

23. 22 Problem: How much current flows through the light bulb pictured below? P = IV I = P/V I = 100W/120V I =.83 Amps The bulb is 100W when it has a potential difference of 120V applied.

24. 23 Electric Bill: Look at an electric bill. You’ll notice that you pay $ for every kilowatt-hour used. ( ~ $.10 per kW hr ) Thus, for every hour you use 1000 Watts, you would pay $ 0.10. A kilowatt hr is a unit of energy.

25. 24 Problem: Maybe your parents are always telling you to turn off the lights and save electricity/money? Look at the light bulb below, how much would it cost to run it for 4 hours? ($0.10 per kW hr) 100W =.1 kW.1 kW x 4 hrs =.4 kW hrs.4kW hrs x $.10 = $.04!

26. 25 Series and Parallel Circuits:

27. 26 Series Circuits: One simple way to arrange components in an electrical circuit is to create one large continuous loop with the components: 2 batteries switch Light bulb resistor Conventional Current

28. 27 Series Circuits: One simple way to arrange components in an electrical circuit is to create one large continuous loop with the components:

29. 28 Series Circuit Characteristics: 1. The current is constant throughout the circuit. 2. Individual components may use varying amounts of voltage 3. The total voltage use is equal to the voltage of the battery/power supply. 4. A break in the circuit interrupts the entire circuit. When resistors are added in series, the total resistance of the circuit is the sum of those individual resistors: R T = R 1 + R 2 + R 3...

30. 29 Parallel Circuits: Another way to connect a circuit is in parallel. In this arrangement, each component is connected separately in its own “loop”. 2 batteries 3 resistors in parallel

31. 30 Parallel Circuits: Another way to connect a circuit is in parallel. In this arrangement, each component is connected separately in its own “loop”.

32. 31 Parallel Circuits: Another way to connect a circuit is in parallel. In this arrangement, each component is connected separately in its own “loop”.

33. 32 Parallel Circuit Characteristics: 1. The current in the different branches can vary. 2. The total current of the circuit is the sum of the individual branches. 3. All branches of the circuit receive the same voltage of the battery/power supply. 4. A break in one loop doesn’t affect the others. To find the equivalent resistance of resistors added in parallel: 1/R T = 1/R 1 + 1/R 2 + 1/R 3 +…

34. 33 Too Many Resistors?: Adding more and more devices in parallel decreases the total or overall resistance. This allows too much current to flow! Obviously this can be dangerous! Fuses and Circuit Breakers: To prevent too much current from causing a fire, fuses are designed to melt and break the circuit before that happens. Today, most homes have circuit breakers. These don’t melt, but are switched off to interrupt the circuit.

35. 34 Meters: A multimeter can measure voltage, current resistance. A multimeter can measure voltage, current and resistance. Meters can provide either digital or analog readouts. DigitalAnalog

36. 35 Measuring Current: Current can be measured using an ammeter or a multimeter. A meter that only measures current is called an ammeter.

37. 36 Using Meters to Measure Current: When measuring current, the meter leads are connected in-line with the load or voltage source. A

38. 37 Using Meters to Measure Current: When measuring current, the meter leads are connected in-line with the load or voltage source. A

39. 38 Connecting a Meter to Measure Current: Notice that the meter leads or probes are placed with the placed in-line with the load. This is called a connection. series connection.

40. 39 Using Meters to Measure Voltage: When measuring voltage, the meter leads (probes) are placed across the load or voltage source. V

41. 40 Connecting a Meter to Measure Voltage: Notice that the meter leads or probes are placed across the load. This is called a parallel connection.

42. 41 Meter Settings: Both the function (DCV, DCA, etc.) switch and the range (0-2V, 0-20V, etc.) switch must be checked and set every time you use a meter - do this before you turn the meter on! Remember: Connecting meters up incorrectly can damage the meter, the load or device being measured and expose you to electrical shock!

43. 42 Series Circuits: One simple way to arrange components in an electrical circuit is to create one large continuous loop with the components: 2 batteries switch Light bulb resistor Conventional Current

44. 43