Presentation is loading. Please wait.

Presentation is loading. Please wait.

Amateur Radio Technician Class Element 2 Course Presentation ELEMENT 2 SUBELEMENTS T1 - FCC Rules, station license responsibilities T2 - Control operator.

Similar presentations


Presentation on theme: "Amateur Radio Technician Class Element 2 Course Presentation ELEMENT 2 SUBELEMENTS T1 - FCC Rules, station license responsibilities T2 - Control operator."— Presentation transcript:

1 Amateur Radio Technician Class Element 2 Course Presentation ELEMENT 2 SUBELEMENTS T1 - FCC Rules, station license responsibilities T2 - Control operator duties T3 - Operating practices T4 - Radio and electronic fundamentals T5 - Station setup and operation T6 - Communications modes and methods T7 - Special operations T8 - Emergency and Public Service Communications T9 - Radio waves, propagation, and antennas T0 - Electrical and RF Safety

2 Station setup and operation T5A  Station hookup – microphone, speaker, headphones, filters, power source, connecting a computer A microphone connects to the transmitter in a basic amateur radio station. A Speaker is a piece of station equipment that converts electrical signals to sound waves. A set of headphones could be used in place of a regular speaker to help you copy signals in a noisy area.

3 Station setup and operation T5A  Station hookup – microphone, speaker, headphones, filters, power source, connecting a computer (cont) A good reason for using a regulated power supply for communications equipment is to protect equipment from voltage fluctuations. A filter would be installed at the transmitter to reduce spurious emissions. A Notch Filter could be connected to a TV receiver as the first step in trying to prevent RF overload from a nearby 2- meter transmitter.

4 Station setup and operation T5A  Station hookup – microphone, speaker, headphones, filters, power source, connecting a computer (cont) Audio feedback is the term used to describe what happens when a microphone and speaker are too close to each other. A Microphone is not required for a packet radio station. A Sound Card can be used to connect a radio with a computer for data transmission.

5 Station setup and operation T5A  Station hookup – microphone, speaker, headphones, filters, power source, connecting a computer (cont) A Terminal Node Controller is connected between the transceiver and computer terminal in a packet radio station. Transceiver TNC Packet Computer

6 Station setup and operation T5B  Operating controls If a transmitter is operated with the microphone gain set too high it may cause the signal to become distorted and unreadable. A VHF/UHF transceiver may be capable of storing in memory the following kinds of information: Transmit and receive operating frequency CTCSS tone frequency Transmit power level One way to select a frequency on which to operate is to use the keypad or VFO knob to enter the correct frequency.

7 Station setup and operation T5B  Operating controls (cont) The squelch control on a transceiver is used to quiet noise when no signal is being received. The purpose of the buttons labeled "up" and "down" on many microphones is to allow easy frequency or memory selection. A way to enable quick access to a favorite frequency on your transceiver is to store the frequency in a memory channel.

8 Station setup and operation T5B  Operating controls (cont) To improve the situation if the station you are listening to is hard to copy because of ignition noise interference may be to turn on the noise blanker. Receiver Incremental Tuning (RIT)

9 NB & RIT Noise blanker RIT – Receiver Incremental Tuning

10 Station setup and operation T5B  Operating controls (cont) The purpose of the "shift" control found on many VHF/UHF transceivers is to adjust the offset between transmit and receive frequency. The purpose of the "step" menu function found on many transceivers is to set the tuning rate when changing frequencies. The purpose of the "function" or "F" key found on many transceivers is to select an alternate action for some control buttons.

11 Station setup and operation T5C  Repeaters; repeater and simplex operating techniques, offsets, selective squelch, open and closed repeaters, linked repeaters One purpose of a repeater is to extend the usable range of mobile and low power stations. A courtesy tone is a tone used to indicate when a transmission is complete. The repeater input and output frequencies is the most important information to know before using a repeater.

12 Station setup and operation T5C  Repeaters; repeater and simplex operating techniques, offsets, selective squelch, open and closed repeaters, linked repeaters (cont) The most common input/output frequency offset for repeaters in the 2-meter band is 0.6 MHz otherwise stated as 600 kHz. The most common input/output frequency offset for repeaters in the 70-centimeter band is 5.0 MHz. The terms input and output frequency when referring to repeater operations means the repeater receives on one frequency and transmits on another.

13 60 miles Offset + 600 kHz Input Freq 147.78 MHz Output Freq 147.18 MHz A repeater is a device used to retransmit amateur radio signals. 2-meter band

14 50 miles Offset + 5.0 mHz Input Freq 447.275 MHz Output Freq 442.275 MHz A repeater is a device used to retransmit amateur radio signals. 70-centimeter band

15 Station setup and operation T5C  Repeaters; repeater and simplex operating techniques, offsets, selective squelch, open and closed repeaters, linked repeaters (cont) The term, simplex operation, means transmitting and receiving on the same frequency. A reason to use simplex instead of a repeater is to avoid tying up the repeater when direct contact is possible. You might find out you could communicate with a station using simplex instead of a repeater if you check the repeater input frequency to see if you can hear the other station.

16 Station setup and operation T5C  Repeaters; repeater and simplex operating techniques, offsets, selective squelch, open and closed repeaters, linked repeaters (cont) You should pause briefly between transmissions when using a repeater to listen for anyone wanting to break in. Linked repeater system is the term for a series of repeaters that can be connected to one another to provide users with a wider coverage. Access to any repeater may be limited by the repeater owner.

17 Station setup and operation T5C  Repeaters; repeater and simplex operating techniques, offsets, selective squelch, open and closed repeaters, linked repeaters (cont) The main reason repeaters should be approved by the local frequency coordinator before being installed is that coordination minimizes interference between repeaters and makes the most efficient use of available frequencies. A closed repeater is the term used to describe a repeater when use is restricted to the members of a club or group.

18 Station setup and operation T5D  Recognition and correction of problems A logical first step when attempting to cure a radio frequency interference problem in a nearby telephone is to install an RF filter at the telephone. The most likely cause of telephone interference from a nearby transmitter is the transmitter's signals are causing the telephone to act like a radio receiver. The following may be useful in correcting a radio frequency interference problem: Snap-on ferrite chokes Low-pass and high-pass filters Notch and band-pass filters

19 Station setup and operation T5D  Recognition and correction of problems (cont) If someone tells you that your transmissions are interfering with their TV reception:  First make sure that your station is operating properly and;  That it does not cause interference to your own television. When a neighbor reports that your radio signals are interfering with something in his home:  The proper course of action to take is to check your station and make sure it meets the standards of good amateur practice.

20 Station setup and operation T5D  Recognition and correction of problems (cont) The most likely cause of telephone interference from a nearby transmitter is the transmitter's signals are causing the telephone to act like a radio receiver. If someone tells you that your transmissions are interfering with their TV reception you should first make sure that your station is operating properly and that it does not cause interference to your own television. The following may be useful in correcting a radio frequency interference problem: (you’ve seen these before) Snap-on ferrite chokes Low-pass and high-pass filters Notch and band-pass filters All of these answers are correct

21 Station setup and operation T5D  Recognition and correction of problems (cont) If a "Part 15" device in your neighbor’s home is causing harmful interference…..

22 Station setup and operation T5D  Recognition and correction of problems (cont) When a neighbor reports that your radio signals are interfering with something in his home the proper course of action to take is to check your station and make sure it meets the standards of good amateur practice. A logical first step when attempting to cure a radio frequency interference problem in a nearby telephone is to install an RF filter at the telephone. If a "Part 15" device in your neighbor’s home is causing harmful interference to your amateur station you should: Work with your neighbor to identify the offending device Politely inform your neighbor about the rules that require him to stop using the device if it causes interference Check your station and make sure it meets the standards of good amateur practice All of these answers are correct

23 Station setup and operation T5D  Fundamental overload  Symptoms of overload and overdrive A fundamental overload, in reference to a receiver, is interference caused by very strong signals from a nearby source. Receiver front-end overload is the result of interference caused by strong signals from a nearby source.

24 Station setup and operation T5D  Distortion If you receive a report that your signal through the repeater is distorted or weak, the problem may be any of the following: Your transmitter may be slightly off frequency Your batteries may be running low You could be in a bad location

25 Station setup and operation T5D  Over and under modulation, RF feedback, Off frequency signals If another operator reports that your SSB signal is very garbled and breaks up, RF energy may be getting into the microphone circuit and causing feedback. Fading and noise If another operator tells you he is hearing a variable high-pitched whine on the signals from your mobile transmitter, the power wiring for your radio could be picking up noise from the vehicle's electrical system. Doppler shift is NOT a cause of radio frequency interference.

26 Station setup and operation T5D  Problems with digital communications links One of the reasons to use digital signals instead of analog signals to communicate with another station is: many digital systems can automatically correct errors caused by noise and interference.

27 Amateur Radio Technician Class Element 2 ELEMENT 2 SUB-ELEMENTS T1 - FCC Rules, station license responsibilities T2 - Control operator duties T3 - Operating practices T4 - Radio and electronic fundamentals T5 - Station setup and operation T6 - Communications modes and methods T7 - Special operations T8 - Emergency and Public Service Communications T9 - Radio waves, propagation, and antennas T0 - Electrical and RF Safety

28 Communications modes and methods T6A  Modulation modes, descriptions and bandwidth (AM, FM, SSB) An amateur radio station used to connect other amateur radio stations to the internet is called a gateway. Repeater Internet Repeater Gateway PC User

29 Communications modes and methods T6A  Modulation modes, descriptions and bandwidth (AM, FM, SSB) (cont) Phone transmissions are voice transmissions by radio. Single sideband (SSB) is a form of amplitude modulation.

30

31 Amplitude Modulation An unmodulated RF carrier requires narrow Bandwidth Modulation of the carrier creates sidebands. This requires more bandwidth. Transmitter power is spread across this bandwidth (on and off is CW)

32 AM and SSB The carrier contains no audio information. The sidebands contain duplicate audio information By filtering out the carrier and one sideband, we save spectrum and concentrate our RF energy into a narrower bandwidth. SSB is therefore more efficient.

33 Communications modes and methods T6A  Modulation modes, descriptions and bandwidth (AM, FM, SSB) (cont) Upper sideband is normally used for VHF and UHF SSB communications. The primary advantage of single sideband over FM for voice transmissions is that SSB signals use much less bandwidth than FM signals.

34 Communications modes and methods T6A  Modulation modes, descriptions and bandwidth (AM, FM, SSB) (cont) Single sideband (SSB) voice modulation is most often used for long distance and weak signal contacts on the VHF and UHF bands. Frequency Modulation (FM) is most commonly used for VHF and UHF voice repeaters. The emission type, CW, has the narrowest bandwidth

35 Bandwidth T6A SSB Signal 2 - 3 kHz wide FM Signal 5 - 15 kHz wide UHF Fast-Scan TV ~ 6 MHz

36 Communications modes and methods T6A  Modulation modes, descriptions and bandwidth (AM, FM, SSB) (cont) The approximate bandwidth of a single-sideband voice signal is between 2 and 3 kHz. The approximate bandwidth of a frequency- modulated voice signal is between 5 and 15 kHz. The normal bandwidth required for a conventional fast-scan TV transmission using combined video and audio on the 70-centimeter band is about 6 MHz.

37 Communications modes and methods T6B  Voice communications, EchoLink and IRLP Information is transmitted between stations via the Internet using Echolink. EchoLink allows computer-to-radio linking for voice transmission. Any licensed amateur radio operator may operate on the Echolink system.

38 Echolink model

39 Echolink screen shot

40 Communications modes and methods T6B  Voice communications, EchoLink and IRLP (cont) If you hear a brief tone and then a station from Russia calling CQ on a 2-meter repeater you are listening to an Internet linked DX station. Voice over Internet Protocol is the method used to transfer data by IRLP. IRLP is a method of linking between two or more amateur stations using the Internet.

41 Communications modes and methods T6B  Voice communications, EchoLink and IRLP (cont) You might find a list of active nodes using VoIP in a repeater directory or the Internet. When using a portable transceiver you select a specific IRLP node by using the keypad to transmit the IRLP node numbers. Echolink and IRLP have in common: Voice over Internet Protocol technology.

42 A typical IRLP Node

43 Communications modes and methods T6C Packet Radio is an example of a digital communications method. Point-to-point digital message forwarding emission mode may be used by a Technician class operator in the 219 - 220 MHz frequency range. Phase Shift Keying (PSK) PSK31 is a low-rate data transmission mode that works well in noisy conditions. Non-voice communications - image communications, data, CW, packet, PSK31, Morse code techniques, Q signals

44 Communications modes and methods T6C  Non-voice communications - image communications, data, CW, packet, PSK31, Morse code techniques, Q signals (cont) Automatic Position Reporting System (APRS) A global positioning system receiver is required along with your normal radio for sending automatic location reports. A standard fast scan color television signal transmission is indicated by the term NTSC.

45 Communications modes and methods T6C  Non-voice communications - image communications, data, CW, packet, PSK31, Morse code techniques, Q signals (cont) Any sending speed at which you can reliably receive is recommended when using Morse code. A practical reason for being able to copy CW when using repeaters is to recognize a repeater ID sent in Morse code.

46 Q-Signals QRM- Man made interference QRN- Natural static / interference QRP- Low Power, under 5 watts QRZ- Who’s Calling? QSB- Fading of signals QSL- Acknowledgement QSO- A conversation QST- A call addressed to all amateurs QSY- Changing frequency QTH- Where you are at

47 RST Readability 1 unreadable, 5 perfectly readable Signal Strength 1 Barely perceptible, 9 extremely strong Tone (CW Only) 1 very bad tone, 9 perfect tone (This is almost always 9, unless there is a problem with their radio)

48 Practice exams on the Internet HTTP://www.qrz.com/p/testing.pl HTTP://www.eham.net/exams/ HTTP://www.aa9pw.com/radio


Download ppt "Amateur Radio Technician Class Element 2 Course Presentation ELEMENT 2 SUBELEMENTS T1 - FCC Rules, station license responsibilities T2 - Control operator."

Similar presentations


Ads by Google