1. ewacker@speedbier.de Draft Beer for Large Events The Lucrative Alternative to Conventional Draft Beer Equipment Serve more people in less time. Success will not stay away

2. TDS Schanktechnik UG presents a new technology which enables caterers and brewers to pour and sell draft beer faster and more profitably Completely Maintenance-Free Easy to handle Easy to clean Practically unbreakable Retro fittable to existing systems Installation Time max. 5 Minutes No Power required Experience from Stadia and Events: Up to 100 % more beer sales ewacker@speedbier.de

3. Five Steps to Faster, More Profitable Beer Sales 1 Original Situation 2 Remove Existing Valve 3 Screw in Adapter 4 Mount Pouring Device, Counter Mount Holder and Drip Cup 5 You are now ready to pour Beer faster and more profitably ewacker@speedbier.de

4. Cooling Technology As June/July 2010 have made quite clear to everybody, summers are getting hotter, which leads to problems mainly at events where available cooling equipment cannot cope with „tropical“ temperatures while beer kegs get warm increasingly faster. Additionally there is extra load on the electrical supply system due to longer run times of air-conditioners, coolers, fans etc. With extreme temperatures parts of the draft beer system also have to be more extreme. This goes mainly for Pressure Regulators Coil Packages Cooling System ewacker@speedbier.de

5. All in all the following can be obtained by employing fast pour technology in conjunction with adequate cooling (Alternative Solutions see below): More turnover through faster pour More cups/glasses per keg through better keg yield More profit through higher turnover at constant cost Minimisation of the number of remaining used kegs Enabling fast pour of beer everywhere, including sites without electricity or mobile sites This with utmost possible technical simplicity, i.e. if possible without electricity and electronics. The following pages list various suggestions for different applications. ewacker@speedbier.de

6. 123 Kegs can be hooked up in series Insulated CO2 Typical Application 1 Cold Plate with pouring device, completely independent from power supply. Preconditions: Ice Cubes (At extreme temperatures approx. 1 Kg Ice for 4 L beer. With pre-chilled kegs approx. 1 Kg Ice for 10 L beer) ewacker@speedbier.de Ice Cubes Cold Plates Insulated Bin

7. 123 Kegs can be hooked up in series Insulated CO2 (Regulator High volume) Typical Application 2 Cold Plates with two pouring devices Completely independent from power supply Only one series of kegs hooked up will supply two valves Preconditions: Ice Cubes CO2 regulator high volume ewacker@speedbier.de Ice Cubes Cold Plates Insulated Bin

8. CO2 Typical Application mobile, no power supply needed. Cold Plate with pouring device for mobile use in stadia or other events Mobile but still uses standard kegs and CO2 Cylinders Preconditions: Ice Cubes (At extreme temperatures approx. 1 Kg Ice for 4 L beer. With pre-chilled kegs approx. 1 Kg Ice for 10 L beer) ewacker@speedbier.de Keg Cold Plate Ice Insulated Tub

9. Ice Requirement: with a Delta T 20 degrees approx. 1 Kg Ice for approx. 4 L Beer (Kegtemperature 25°C) = 25 Kg Ice per 1 hL beer with a Delta T 8 degrees approx. 1 Kg Ice for approx. 10 L Beer (Kegtemperature ca. 10 – 12 °C) = 10 Kg Eis per 1 hL beer With a Delta T 4 degrees approx. 1 Kg Ice for approx. 20 L Beer (Kegtemperature < 8 °C) = 5 Kg Eis per 1 hL beer Application: Events of any kind, creation of new sales points without electricity. Mobile Kiosks Sports Stadia, Kiosks and Events in the Infield ewacker@speedbier.de

10. 123 Kegs can be hooked up in series CO2-Pressure Regulator Fob Stop Power Cooler Beer Inlet into cooler Typical Application 3 Power Cooler and one Pouring Device mounted on top of cooler or remote Cooler needs to be filled with water and builds Ice Bank. ewacker@speedbier.de Preconditions Electricity Water

11. 123 Kegs can be hooked up in series. Beer line is split inside cooler and supplies two pouring devices. This ensures small number of remaining used kegs CO2-Pressure Regulator, High Volume Fob Stop ewacker@speedbier.de Beer Inlet Typical Application 4 Power Cooler and two Pouring Devices Quasi ready for use Cooler needs to be filled with water and builds Ice Bank Preconditions: Electricity Water Pressure Regulator High Volume Power Cooler

12. 123 Kegs can be hooked up in Series Insulated or better even with ancilliary cooling CO2 Typical Application 5 Remote Flash Cooler and Pouring Device. Typical application where device is mounted onto already existing draft beer systems. Preconditions: Electricity Water Pre-chilled Kegs ewacker@speedbier.de

13. 123 Insulated or better even with ancilliary cooling Kegs can be hooked up in series. Beer line is split inside cooler and supplies two pouring devices. This ensures small number of remaining used kegs Typical Application 6 Flash Cooler and two Pouring Devices Preconditions: Electricity Water Pre-chilled Kegs Pressure Regulator High Volume ewacker@speedbier.de Existing Dispense Head Pouring Device is mounted instead of the existing valve CO2 Pressure Regulator High Volume

14. Video Clips are available on YouTube or on CD. Ask for URLs or CDs at: TDS Schanktechnik UG Ekhard Wacker Drosselweg 5 37520 Osterode Germany Tel.:+49 05522 5057172 Mobile:+49 0171 6405052 ewacker@speedbier.de