Two Minute Drill Number 26- Residential Improving your skill in code Look Up Increasing Speed Drill Copyright 2008 Ted "Smitty" Smith.

Directions Left click on the presentation ICON located at the bottom of the slide directory to the left of the this slide. Each slide will transition to the correct answer automatically in 2:00 minutes. The correct answer will transition in 15 seconds. As you progress through the slide show, the time for each question will be reduced. Write down the correct answer to each question and the code reference as it is displayed so you can review them later. This presentation is mostly concerning Residential. We have included a few other categories just to help keep you sharp. Copyright 2008 Ted "Smitty" Smith

1. A listed instantaneous water heater shall be permitted to be subdivided into circuits protected at NOT more than _____. a. 60 amperes b. 100 amperes c. 120 amperes d. 150 amperes Copyright 2008 Ted "Smitty" Smith

3. The continuity of the grounding conductor system for portable electrical carnival equipment shall be verified _____. a. And recorded on an annual basis b. And recorded on a quarterly basis c. And recorded on a monthly basis d. Each time the equipment is connected Copyright 2008 Ted "Smitty" Smith

5. Determine the MAXIMUM allowable ampacity of a size 1/0 AWG THW copper current-carrying conductor installed in a common raceway with three other current-carrying conductors of the same size. Ambient temperature is 86ºF. a. 150 amperes b. 105 amperes c. 112 amperes d. 120 amperes Copyright 2008 Ted "Smitty" Smith

6. The NEC® defines a continuous-load to be a load where the maximum current on the circuit is expected to continue for at least _____ hours or more. a. 3 b. 4 c. 6 d. 8 Copyright 2008 Ted "Smitty" Smith

7. Determine the MINIMUM size THW copper branch-circuit conductors required by the NEC® to supply a three-phase, continuous duty, AC motor that has a full-load current of 70 amperes. Assume all terminations to be rated at 75ºC. a. 1 AWG b. 2 AWG c. 3 AWG d. 4AWG Copyright 2008 Ted "Smitty" Smith

8. Given: you have determined a conductor has a computed allowable ampacity of 75 amperes. What is the MAXIMUM standard ampere rating of the overcurrent protection device the NEC® permits to protect this circuit? This is not a motor circuit or part of a multi-outlet branch-circuit supplying receptacles. a. 70 amperes b. 75 amperes c. 80 amperes d. 85 amperes Copyright 2008 Ted "Smitty" Smith

9. A 208-volt, three-phase, 50HP, squirrel- cage, continuous duty, Design C, AC motor has a full-load running current of ______. a. 130 amperes b. 143 amperes c. 162 amperes d. 195 amperes Copyright 2008 Ted "Smitty" Smith

10. Which of the following metal piping systems contained in a building is/are required to be bonded? a. A gas pipe for a gas heater b. A bathroom copper water pipe, connected to an electric water heater. c. An air line for compressed air d. All these need to be bonded. Copyright 2008 Ted "Smitty" Smith

11. Determine the MINIMUM trade size electrical metallic tubing (EMT) required to enclose eight size 6 AWG copper conductors with THHW insulation, installed in a 60 foot conduit run. a. 1 inch b. 1 ¼ inch c. 1 ½ inch d. 2 inch Copyright 2008 Ted "Smitty" Smith

12. When a feeder supplies a continuous-load of 240 amperes, in general, the overcurrent protection device protecting this circuit shall have a MINIMUM rating of _____. a. 240 amperes b. 300 amperes c. 250 amperes d. 275 amperes Copyright 2008 Ted "Smitty" Smith

13. In general, liquid-tight flexible metal conduit (LFMC) shall be securely fastened within _____ of each box or other conduit termination. a. 4 ½ feet b. 3 feet c. 12 inches d. 18 inches Copyright 2008 Ted "Smitty" Smith

14. When a pull box contains conductors of size 4 AWG and larger and a straight pull of the conductors is to be made, the length of the box shall NOT be less than _____ times the trade diameter of the largest conduit entering the box. a. Six b. Four c. Eight d. Twelve Copyright 2008 Ted "Smitty" Smith

15. In general, all of the following wiring methods listed are permitted to be used as a feeder for temporary wiring on a construction site EXCEPT _____. a. NM cable b. NMC Cable c. Type PD cord d. Type SJO cord Copyright 2008 Ted "Smitty" Smith

1 6. Determine the MAXIMUM number of size 14 AWG THHN conductors permitted to be installed in a trade size 3/8 inch flexible metal conduit (FMC) that contains a bare size 14 AWG grounding conductor when the flex has external fittings. a. Two b. Three c. Four d. five Copyright 2008 Ted "Smitty" Smith

17. Which of the following listed conduits does the NEC® permit to enclose conductors feeding wet-niche underwater pool lights? a. Electrical metallic tubing (EMT) b. Electrical nonmetallic tubing (ENT) c. Galvanized rigid metal conduit (RMC) d. Schedule 40 rigid polyvinyl chloride conduit (PVC) Copyright 2008 Ted "Smitty" Smith

18. Underground wiring is not permitted under a swimming pool or within _____ of the pool unless the wiring is supplying pool equipment. a. 10 feet b. 6 feet c. 5 feet d. 8 feet Copyright 2008 Ted "Smitty" Smith

19. Which of the following listed types of batteries is NOT permitted for use as a source of power for emergency systems? a. Automotive b. Lead acid type c. Alkali type d. All of these Copyright 2008 Ted "Smitty" Smith

20. The MINIMUM rating for a service disconnecting means for a building, other than a one-family dwelling, consisting of three, two-wire circuits shall be _____. a. 15 amperes b. 30 amperes c. 60 amperes d. 100 amperes Copyright 2008 Ted "Smitty" Smith

End of Drill Click the left mouse button to advance back to the first question. Each question will now be repeated without the timer to give you a chance to review it and find the answer. Clicking the left mouse button will advance the slide to the answer and the code reference. Copyright 2008 Ted "Smitty" Smith