Download presentation
Presentation is loading. Please wait.
Published byRalph Bailey Modified over 9 years ago
1
Physical Transmission Media Chapter 8
2
Objectives In this chapter, you will learn to: Identify the characteristics of wireline transmission Describe the properties and uses of coaxial cable Describe the properties and uses of different types of twisted- pair wire Identify the characteristics of lightwave transmission Describe the properties and uses of fiber optic cable Identify factors to consider when selecting a telecommunications medium Explain and apply cabling standards Describe best practices for installing wire and fiber optic cabling Identify techniques for testing the continuity and performance of physical transmission media
3
Characteristics of Wireline Transmission Impedance: expressed in Ohms, is the combined effect of a circuit’s inductance and capacitance. Propagation Delay and Latency: the difference in time between a data packet’s transmission and its reception over a specific route. Distortion: the unintended and undesirable modification of at least one signal component, which makes the signal different from how it was originally transmitted. Noise: any unwanted interference from external sources.
4
Example graph of a waveform and some distorted versions of the same waveform
5
Crosstalk In electronics, crosstalk is any phenomenon by which a signal transmitted on one circuit or channel of a transmission system creates an undesired effect in another circuit or channel. Crosstalk is usually caused by undesired capacitive, inductive, or conductive coupling from one circuit, part of a circuit, or channel, to another.
6
Crosstalk cont..
7
Impulse Noise
8
Thermal Noise
9
IQ TEST1 1.What is impedance expressed in? Answer: Ohms 2. The type of loss caused by impedance mismatches is known as _____. Answer: return loss 3. The difference in time between a data packet’s transmission and it reception over a specific route is known as _____. Answer: propagation delay 4. _____ refers to the amount of time it takes a bit of data to traverse a network link. Answer: latency 5. _____ occurs when a signals traveling on one wire infringe on a nearby wire’s signal. Answer: Crosstalk
10
Coaxial Cable
11
Non-twisted Wire
12
Level 1 Terminations
13
Twisted Pair (TP)
14
Shielded Twisted Pair (STP)
15
Unshielded Twisted Pair (UTP)
16
Category 3 (CAT3)
17
Category 5 (CAT5)
18
Fiber Optic Cable
20
Popular Uses for Fiber Optic Cable Includes connecting: Regional and local cable TV facilities Internet NAPs with other large telecommunications exchange point Central offices with other central offices Main feeders with central offices A telecommunication’s network with private LANs A telecommunication’s network with private switching systems, such as PBX
21
Selecting Appropriate Media When selecting telecommunications media consider: Existing infrastructure Throughput potential Cost of installation Noise immunity Security Size and scalability
22
Comparison of Physical Media
24
Structured Cabling
25
Backbone Wiring
26
Telecommunications Closet
28
Horizontal Wiring
29
Work Area
31
Installing UTP
32
Crossover Cable
33
Installation Tips for CAT5 UTP Do not untwist twisted-pair cables more than one-half inch before inserting them into the punch-down block or connector. Pay attention to the bend radius limitations for the type of cable you are installing. Test each segment of cabling as you install it with a cable tester. Use only cable ties to cinch groups of cables together
34
Installation Tips for CAT5 UTP When pulling cable, do not exert more than 25 pounds of pressure on the cable. Avoid laying cable across the floor where it might sustain damage from rolling chairs or foot traffic. Install cable at least three feet away from fluorescent lights or other sources of EMI. Always leave slack in cable runs.
35
Installing Fiber Splice - the physical joining of two facing and aligned pieces of wire or fiber. Mechanical splicing - the two ends of a fiber optic cable are fixed in position within a tube so that they form one continuous communications channel. Fusion splicing - a connection between fibers is accomplished through the application of heat and the resulting melting and fusion of two fiber strands.
36
Mechanical and Fusion Splicing
37
ST and SC Fiber Connectors
38
Cable Installation Tips for Fiber Optic Cable When pulling fiber optic cable, do not exert pressure on the cable. Fiber optic cable should be installed within a conduit whenever you are concerned about the potential for environmental damage. Do not exceed the minimum bend radius.
39
Troubleshooting Connectivity Problems Identify the symptoms Identify the scope of the problem Establish what has changed on the network Determine the most probable cause of the problem Implement a solution Test the solution Recognize the potential effects of the solution Document the solution
40
Troubleshooting Tools Crossover Cable - allows you to quickly and easily verify that a node’s network adapter is transmitting and receiving signals properly. Tone Generator - a small electronic device that issues a signal on a wire pair. Tone Locator - a type of amplifier that can detect the inductive energy emitted by the tone (current) on a wire.
41
Tone Generator and Tone Locator
42
Continuity Tester
43
Performance Testers Provides the following functions: Measures the length of each wire pair Ensures that the cable does not exceed recommended maximum lengths Measures the distance from the tester to a cable fault Measures attenuation along a cable Measures crosstalk between wires
44
Performance Testers
45
Fiber Optic Cable Testers
46
Time Domain Reflectometers
47
Telephone Test Set
48
IQ TEST 2 1.The extent to which a lightwave signal weakens along a length of Answer: optical loss 2. In the context of fiber optic cable, a physical joining of two facing and aligned pieces of wire or fiber is known as a(n) _____. Answer: splice 3. In _____, the two ends of a fiber optic cable are fixed in position within a tube so that they form one continuous communications channel. Answer: Mechanical splicing 4. In _____, a connection between fibers is accomplished through the application of heat and the resulting melting and fusion of two fiber strands. Answer: fusion splicing 5. _____ refers to the splicing of multiple fiber optic strands at once, whether by fusion or mechanical means. Answer: Mass splicing
49
Summary Characteristics that affect wireline transmission include impedance changes, latency, delay distortion, and noise. Traditional four-pair, non-twisted copper telephone wiring is known as Level 1 cable or quad wire. Category (CAT3) UTP cable is the minimum grade of unshielded twisted-pair cabling for use in telephone systems. To identify the source of cabling infrastructure problems, follow a logical troubleshooting methodology and have the appropriate testing tools handy.
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.