1. General Licensing Class Oscillators & Components Your organization and dates here

2. 2 Amateur Radio General Class Element 3 Course Presentation  ELEMENT 3 SUB-ELEMENTS (Groupings) 1 - Your Passing CSCE 2 - Your New General Bands 3 - FCC Rules 4 - Be a VE 5 - Voice Operations 6 - CW Lives 7 - Digital Operating 8 - In An Emergency 9 - Skywave Excitement

3. 3 Amateur Radio General Class Element 3 Course Presentation  ELEMENT 3 SUB-ELEMENTS (Groupings) 10 - Your HF Transmitter 11 - Your Receiver  12 - Oscillators & Components 13 - Electrical Principles 14 - Circuits 15 - Good Grounds 16 - HF Antennas 17 - Coax Cable 18 - RF & Electrical Safety

4. Oscillators & Components  The basic components of virtually all sine wave oscillators are a filter and an amplifier operating in a feedback loop. (G7B07) Sine wave Square wave Triangle wave Sawtooth wave Voltage waveforms

5. Oscillators & Components  The inductance and capacitance in the tank circuit determines the frequency of an LC oscillator. (G7B09) Tank Circuits Inductors(variable) Capacitors

6. Oscillators & Components  The control grid is the element of a triode vacuum tube is used to regulate the flow of electrons between cathode and plate. (G6B10)  The primary purpose of a screen grid in a vacuum tube is to reduce grid-to-plate capacitance. (G6B12) H=Heater/Filament; C=Cathode; S=Screen Grid; P=Plate

7. Oscillators & Components  A Field Effect Transistor is the solid state device most like a vacuum tube in its general operating characteristics. (G6B11) In the construction of a MOSFET the gate is separated from the channel with a thin insulating layer. The Gate is similar to the grid of a tube, it controls current flow.

8. Oscillators & Components  The cases of some large power transistors must be insulated from ground to avoid shorting the collector or drain voltage to ground. (G6B08) Power Transistors Insulating wafer

9. Oscillators & Components  The stable operating points for a bipolar transistor used as a switch in a logic circuit are its saturation and cut-off regions. (G6B07) Saturation is where the transistor is Base biased for maximum emitter to collector current flow Cut-off is where the transistor is base biased for minimum emitter to collector current flow  In a MOSFET, the gate is separated from the channel with a thin insulating layer. (G6B09)

10. Oscillators & Components  The approximate junction threshold voltage of a germanium diode is 0.3 volts. (G6B03) This is the voltage drop across the diode junction when it is conducting in the forward direction.  The approximate junction threshold voltage of a silicon diode is 0.7 volts. (G6B05) This is the voltage drop across the diode junction when it is conducting in the forward direction  Lower capacitance is an advantage of using a Schottky diode in an RF switching circuit as compared to a standard silicon diode. (G6B06) It is desirable to have low capacity across the diode junction in higher frequencies where the capacitive reactance forms a significant path around the diode when reverse (Back) biased in the non conductive state.

11. Oscillators & Components  High power consumption is one disadvantage of an incandescent indicator compared to a LED. (G6C07)  An LED is forward biased when emitting light. (G6C08) Array of LEDs and resistors

12. Oscillators & Components  LCDs do not emit light. Therefore, a liquid crystal display requires ambient or back lighting. (G6C09)  A microprocessor is a computer on a single integrated circuit. (G6C11) Basic microprocessor

13. Oscillators & Components  The term MMIC means Monolithic Microwave Integrated Circuit. (G6C02)  Analog is also the term that describes an integrated circuit operational amplifier. (G6C06) Schematic symbol Integrated circuit MMIC devices Signal connections

14. Oscillators & Components  The two major ratings that must not be exceeded for silicon-diode rectifiers are peak inverse voltage; average forward current (G6B02)  An advantage of using the binary system when processing digital signals is that binary "ones" and "zeros" are easy to represent with an "on" or "off" state. (G7B02) In digital systems, binary numbers are used to write and keep track of the many possible combinations of the two electrical states

15. Oscillators & Components  For a two input AND gate, the output is high only when both inputs are high. (G7B03) Truth table for AND Gate

16. Oscillators & Components  For a two input NOR gate, the output is low when either or both inputs are high. (G7B04) Truth table for NOR Gate

17. Oscillators & Components  Integrated circuits that provide more complex logic functions, such as counters and shift registers, are also available. A 3-bit binary counter has 8 states. (G7B05) There are 8 states in a 3-bit binary counter.  000 001 010 011  100 101 110 111  A shift register is a clocked array of circuits that passes data in steps along the array. (G7B06) 4-Bit SIPO Shift Register

18. Oscillators & Components  A linear voltage regulator, is an example of an analog integrated circuit. (G6C01) Schematic symbols and actual linear voltage regulators

19. Oscillators & Components  Low power consumption is an advantage of CMOS integrated circuits compared to TTL integrated circuits. (G6C03) CMOS is the most commonly used digital logic family of integrated circuits.  The term ROM means Read Only Memory. (G6C04)  ROM is characterized as “non-volatile,” meaning the stored information is maintained even if power is removed. (G6C05)  Complex digital circuitry can often be replaced by a microcontroller. (G7B01) Intel 8742 DVD Recorder LSI Devices