1. The Design and Development of an Active Smart Wing Model ATAK Technologies

2. Team Structure Thomas Ayers Thomas Ayers Project Leader Project Leader Assistant Testing Engineer Assistant Testing Engineer Robert Aguirre Robert Aguirre Senior Research Specialist Senior Research Specialist Kevin Mackenzie Kevin Mackenzie Senior Modeling and Design Specialist Senior Modeling and Design Specialist Vu Tran Vu Tran Senior Testing Specialist Senior Testing Specialist Dr. R. O. Stearman Dr. R. O. Stearman University of Texas Faculty Consultant University of Texas Faculty Consultant

3. Presentation Overview Background Information Background Information Aerodynamic Theory Aerodynamic Theory Model Design Model Design Past Group Work Past Group Work Present Group Work Present Group Work Summary Summary Questions Questions

4. Project Background Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Randall Bolding Wrote a master’s thesis in 1978 in which a wing model was used to research the use of a stabilator as an active control to suppress flutter Lockheed Martin Corporation A research project on the benefits that an active wing can provide in contemporary aircraft design

5. High Airspeed Benefits Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions At high airspeeds normally latent aerodynamic forces become powerful enough to affect the flow about the airfoil These changes cause torsional moments on the wing Theoretically, the use of active wing control on the leading edge flaps and ailerons can be used in order to better control these latent aerodynamic forces

6. Low Airspeed Benefits Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions At low speeds airflow about the wing can separate from the wing causing a “stall” In natural flight, resonant flapping is used to sustain flight at low flight speeds Theoretically, oscillating the wings by using the control surfaces would create high lift conditions for short, low airspeed maneuvers

7. Aerodynamic Theory Background Information Background Information Aerodynamic Theory Aerodynamic Theory Model Design Model Design Past Group Work Past Group Work Present Group Work Present Group Work Summary Summary Questions Questions

8. Aerodynamic Force: Lift Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Air flows around the airfoil and create 2 different velocity regions along the top and bottom surfaces of the wing. velocity increases pressure decreases Lift is generated due to pressure gradient along the surfaces of the wing. [2]

9. Lift Coefficient vs. Angle of Attack Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Lift Analysis = Lift Coefficient Analysis The amount of lift generated by the wings depends on the shape of the airfoil and its inclination with respect to the flow direction. The lift varies almost linearly for small angles of attack (within +/- 10 degrees) [1]. http://www.centennialofflight.gov/essay/Dictionary/angle_of_attack/DI5.htmhttp://www.centennialofflight.gov/essay/Dictionary/angle_of_attack/DI5.htm Feb 2003 [2]

10. What is Stall? Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Stall occurs when the boundary layer separates from the surface of the wing, causing the lift dramatically decrease. Wing area exposed to the flow increases, thus increasing drag and decreasing velocity. Flow becomes highly unsteady behind the airfoil – turbulence flow. http://wright.nasa.gov/airplane/incline.htmlhttp://wright.nasa.gov/airplane/incline.html Feb 2003

11. What is Vstall? Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions The velocity of the aircraft when it stalls, which determines the minimum velocity an aircraft can fly. CLmax is the ideal parameter to optimize in order to reduce stall speed How to increase CLmax? - Trailing-edge flaps - Leading edge slats - Oscillating flaps (New)

12. Lift-Enhancing Devices Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Flaps change the pressure distribution around the airfoil by changing its chord length and camber, also increase wing area to decrease stall speed. The effect of camber on lift can be explained qualitatively with Newtonian approach and Thin Airfoil Theory. Newtonian approach: Lift is the result of pressure reactions that oppose the turning of flow – higher lift is caused by greater turning Thin Airfoil Theory: http://www.desktopaero.com/appliedaero/airfoils2/highlift.htmlhttp://www.desktopaero.com/appliedaero/airfoils2/highlift.html Feb 2003[2]

13. Lift-Enhancing Devices Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Slats – an opening at the leading edge of the airfoil allowing high pressure air under the airfoil to pass. The high pressure air mixes with the air at the top surface and increases the energy of the boundary layer. “By increasing the energy of the boundary layer the wing can sustain higher angles of attack and a higher maximum coefficient of lift” [3] [3]

14. Lift-Enhancing Devices Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Oscillating Flap – located near the leading edge of the wing to control the separation of the airflow from the wing – delay the separation or reattach the separated flow onto the surface Vortices are created by oscillating flaps – “enhance the momentum transfer between the free stream and boundary layer, which makes the reattachment of vertices occur more upstream” [3] – the further upstream the vertices are, higher Clmax can be achieved. Moreover, “Clmax is further increased if excitation frequency of flap corresponds to the vortex shedding frequency” [3]

15. Model Design Background Information Background Information Aerodynamic Theory Aerodynamic Theory Model Design Model Design Past Group Work Past Group Work Present Group Work Present Group Work Summary Summary Questions Questions

16. Actuator Designs Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Hydraulic Actuator Electromechanical Actuator Electric Motor

17. Hydraulic Actuator System Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Available – Dr. Stearman had a hydraulic unit for group use Fast response – Can oscillate at required frequency Powerful – Can easily drive the model control surfaces

18. How do Hydraulics Work? Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Force that is applied at one point is transmitted to another point using an incompressible fluid. Varying the area of the pistons changes the force output. In this example, the area of the right piston is 9 times greater than the other piston and the force output is thus 9 times the force input. http://science.howstuffworks.com/hydraulic.htmhttp://science.howstuffworks.com/hydraulic.htm Feb 2003http://science.howstuffworks.com/hydraulic.htmhttp://science.howstuffworks.com/hydraulic.htm Feb 2003

19. Hydraulic System - Drawbacks Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Complex – System requires power source, high pressure motor, fluid and tubing Expensive – Available system lacked power source ($500) Size – System is awkward and not easy to set up Maintenance – Pumps, filters need constant up keep

20. Electromechanical Actuation Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Size – Overall system is much smaller Cost – Motor and controller are available from Dr. Stearman for free Maintenance – Does not require any form of maintenance

21. How does the controller work? Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions A controller drives a motor coupled to a shaft that drives the flaps [2]

22. Electromechanical Drawbacks Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Complexity of controller – Circuit diagram is over 2 pages Size – The controller alone weighs over 35lbs. and would be difficult to mount in the wind tunnel Limited applications – Can only control leading edge flaps [2]

23. ATAK Technologies Design Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Size of Control System – Electric motor and shaft will be half the size of the previous groups Ease of Operation – Does not require understanding of complex controller Able to Test – By taking wind tunnel dimensions into account when designing we make sure that we will be able to mount the wing in order to obtain Cl and Cd measurements Flexibility – Leading and trailing edge flaps will be able to oscillate. Will be able to control angle of deflection and phase between flaps [1]

24. How will our control system work? Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions  Motor mounted to main spar  Shaft drives slider crank assemblies that cause the flaps to oscillate  Hand held tachometer will measure revolutions per minute of the flaps [1] [2]

25. Project Accomplishments Background Information Background Information Aerodynamic Theory Aerodynamic Theory Model Design Model Design Past Group Work Past Group Work Present Group Work Present Group Work Summary Summary Questions Questions

26. Past Accomplishments Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Project has been advanced in past three terms Project has been advanced in past three terms The Active Wing Group (AWG) The Active Wing Group (AWG) Active Wing Technology (AWT) Active Wing Technology (AWT) Active Wing Engineering (AWE) Active Wing Engineering (AWE)

27. The Active Wing Group Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions AWG Work AWG Work Recovered F-111 wing-tail from storage Investigated limit cycle oscillations Provided a strong foundation for Summer 2002 group AWG Suggestions AWG Suggestions Prioritize system hardware recovery

28. Active Wing Technologies Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Research Research Primarily Research on F-111 Limit cycle oscillations Increasing lift on fighter wings Implementation of control surfaces Digital and analog control systems

29. Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions AWT Suggestions Create a mathematical model of control system Create a mathematical model of control system Create model using either Root Locus or Bode Plot in MatLab Create digital schematics of all drawings Create digital schematics of all drawings

30. Research Research Aerodynamic Theory behind oscillating flaps Selected actuation system Selected actuation system Constructed model wing with leading edge flaps Constructed model wing with leading edge flaps Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Active Wing Engineering

31. AWE Suggestions Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Add leading and trailing edge flaps to new design Add leading and trailing edge flaps to new design Create actuation system to control leading and trailing edge flaps Create actuation system to control leading and trailing edge flaps Select wing type Select wing type Swept, tapered; Straight, non-tapered Incorporate Measuring tools for wind tunnel tests Incorporate Measuring tools for wind tunnel tests

32. Progress Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Research Research Aerodynamic forces involved in active wing technologies Control surface effect on lift Model Design Model Design Actuation and controller systems AutoCAD design of wing model AutoCAD design of wing model Lab Maintenance Lab Maintenance Worked to clean WRW 316

33. Remaining Tasks Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions Model Design Model Design Finalize wing model Construct wing model Incorporate testing system Perform wind tunnel test Perform wind tunnel test Reduce data for analysis

34. Projected Schedule Background Background Theory Theory Model Model Work Work Summary Summary Questions Questions

35. Presentation Summary Presentation Summary Background Information Background Information Aerodynamic Theory Aerodynamic Theory Theory Behind the Model and Design Work Theory Behind the Model and Design Work Past Group Work Past Group Work Present Group Work Present Group Work Future work for ATAK Technologies Future work for ATAK Technologies

36. References [1]Aguirre, Robert, Thomas Ayers, Kevin Mackenzie, and Vu Tran. “Design and Development of an Active Wing Model.” ATAK Technologies, Austin, TX, Mar. 2003. [2]Garret, Carlos, Justin Gray, and Kevin Marr. “Design of an Active Controlled Wing Model Using Flap Oscillation.” AWE Engineering, Austin, TX, Dec. 2002. [3]Fuentes, David, Basil Philips, and Naoki Sato. “Design and Control Modeling of an Active Variable Geometry Wing.” Active Wing Technologies, Austin, TX, Aug. 2003.

37. Questions?