1. USB DAQ Product USB DAQ Product Κώστας Γρηγορίου Sales Engineer Ιούνιος 26, 2007

2. USB-enabled Device Forecast  With continued adoption of USB in the consumer electronics and communications segments, and the rapid introduction of high- speed USB into PCs and PC peripherals, the total market for USB-enabled devices will experience 18.3% annual growth between 2003 and 2008.

3. Why USB-based DA&C Module?  Standard I/F on most new computers  Becoming a new industry standard  Easy Installation: hot-swappable, plug-and-play  Connect up to 127 devices to a single USB host  Compact size, economic packaging  Plugable terminal blocks for easy connection  One cable supplies both power & signal connection. No external power or battery is required (may <5m)  High-performance 480Mbps transmission  Isolated shielded box & direct I/O connection from sensors, useful for portable AP & noisy environment

4. What’s Advantech Design Concept ?  Keep the same specification and driver as our existed PCI-bus DA&C cards, for R&D easy to develop and diagnostic the system. –The same H/W and S/W between development and run-time –Save time and effort on simulation and trouble shooting –Portable and plug-and-play

5. USB Data Acquisition Series USB-4711USB-4718USB-4716 12-bit, 100kS/s 16 AI/ 2AO 8DI/ 8DO TTL 16-bit counter x 1 High Speed USB 2.0 No need for external power 12-bit, 100kS/s Multifunction Module 16-bit, 100kS/s Multifunction Module 8-Ch Thermocouple Input Module 16-bit, 100kS/s 16 AI/ 2AO 8DI/ 8DO TTL 16-bit counter x 1 USB 2.0 No need for external power 8-Ch thermocouple J,R,K,S,T,B,E type 3000V DC isolation USB 2.0 No need for external power

6. USB-4711 USB-4711 - 100kS/s, 12-bit Multifunction Module Targeting Positioning Segmentation Hand-carry data acquisition applications  Embedded System For Harsh Environment Portable multi-function device Lab users Laptop Application Features Support High-Speed USB 2.0 16AI / 2AO / 8DI / 8DO Channels No need for external power supply Removable screw terminal block 145 mm 30 mm 100mm Weight: 150g 100 mm

7. 16 S.E. Channels AI 8-Ch DI/ 8-Ch DO 2 Channels AO USB-4711 USB-4711 - 100kS/s, 12-bit Multifunction Module 12 bits resolution 100kS/s sampling rate 1K FIFO memory External trigger source applicable with GATE control Auto Calibration 0~5, 0~10, +/-5, +/-10 V multiple output range 5mA driving capability TTL Compatible 1 Counter

8. Fast USB 2.0 Bus Support 480Mbps Data Rate USB-4711 can operate at up to 480Mbps to fulfill the fast data transfer and realize the high speed data acquisition No need for external power Because of the low power consumption, USB-4711 can work under the internal USB 500mA power supply, which means users don’t have to worry about the power source even when they are in the outdoors. Hot swapable and P&P function Users can install or remove USB-4711 without reboot or shut down there system. Give them the quick and convenient operation USB 2.0

9. Thoughtful mechanism design for your on-to- go application Removable screw terminal for easy wiring You can just switch the screw terminals for various kind of wiring diagrams without any re-wiring efforts. Pre-marked pin assignment index makes your wiring work quick and straight. Removable terminal P/N: 1652610101 LED indicator LED indicator gives you the guide of the current status of the device. Skid-proof rubber feet 4 rubber feet let your device stands firm and soundly LED Status DescriptionOn Ready for work Off Not ready for work Slow blinking Device installation Fast Blinking Working On-module pin assignment index

10. Installation of USB-4711  Support both USB 2.0 and USB 1.1 –USB 1.1 speed: 12M bits/s –USB 2.0 speed: 480M bits/s Note: The AI can only up to 2kS/s when using USB 1.1

11. Operation of USB-4711 (I)  Fully support the same driver with DA&C card (ADSAPI32 DLL, ActiveDAQ & LabVIEW)

12. Operation of USB-4711 (II)  Easily update the firmware of USB-module in dedicated Utility for upgrading.

13. Target Applications  Automated test and measurement  Data logging  Temperature measurement  Environmental monitoring and control  Process monitoring and control  Quality control  Laboratory automation  Portable data acquisition  Production test  Electronics test  Semiconductor test  Telecommunications  Calibration  Research and development

14. WaveScan Utility – Setting

15. WaveScan Utility – Waveform Scan

16. WaveScan Utility – Storage

17. WaveScan Utility – Scaling

18. Overview DAQ wherever you like (portable DAQ solution without programming)  USB-4711: 100kS/s Multifunction Module (USB-based, no external power is needed)  Wavescan utility: to display the acquired signals, also can save to HDD for further analysis Wavescan utility

19. Thank You