1. Interactive Intelligence Putting you in Control…
Controls
V 1.08
Sebastien Desmottes - Controls Development Engineer @ Plymouth (UK)

2. Controls Product Contents
RBC-RDx-PE: Refrigerant Detection
RBC-FDP1-PE: Fault Display Panel
RBC-CRx-PE: Central Remote Controller
RBC-WG1-PE: Windows Gateway
RBC-WP1-PE: Windows Software
RBC-EM1-PE: Energy Monitoring
RBC-IK1-PE: Internet Kit

3. Refrigerant Detection
Indoor / Outdoor
RBC-RD1-PE / RBC-RD2-PE

4. Refrigerant Detection Contents
Why Refrigerant Detection
Options available
Indoor Unit: RBC-RD1-PE
Outdoor Unit: RBC-RD2-PE
System Layout
Electrical Installation
System Operation
Installation Indoor / Outdoor
Note: RBC-RD1-PE, RBC-RD2-PE

5. Refrigerant Detection Why Refrigerant Detection?
To protect personnel (EN 378)
To prevent environmental damage
To maintain system efficiency
Government Tax Incentives
Note: RBC-RD1-PE, RBC-RD2-PE

6. Refrigerant Detection Options Available
Indoor Unit: RBC-RD1-PE
Interface box with remote refrigerant sensor & audible alarm
Outdoor Unit: RBC-RD2-PE
Interface box with internal sensor
RBC-RDx-PE
Note: RBC-RD1-PE, RBC-RD2-PE

7. Refrigerant Detection Indoor Unit: RBC-RD1-PE
Control box and screw caps
Remote sensor/audible alarm assembly
Front plate
FCU interface cable
Installation instructions
Owners manual
RBC-RD1-PE

8. Refrigerant Detection Outdoor Unit: RBC-RD2-PE
Control box with integral sensor and screw caps
CDU interface cable
Mounting bracket and screw
Installation Instructions
Owners Manual
RBC-RD2-PE

9. Refrigerant Detection RBC-RD1-PE System Layout
FCU Electrical Box
Hotel Room
Metal oxide refrigerant detector. Low level position with audible alarm and 3 alarm set-points
Standard XY communication protocol
Front end PC running Windows control package (RBC-WP1-PE). Displays alarm message and unit location.
Isolating solenoid valves positioned in the gas and liquid lines (supplied by installer).
Interconnecting cable: control and Sensor.
Gateway: RBC-WG1-PE XY PQ
RBC-RD1-PE

10. Refrigerant Detection RBC-RD1-PE System Layout
Liquid Line
Suction Line
To Indoor Network
Communication cable
Sensor located close to the floor monitors room air.Emits audible alarm when 1000ppm refrigerant (R407C) detected.
RD1 box near unit sends signal to solenoid valves and indoor unit.

11. Refrigerant Detection Electrical Installation RBC-RD1-PE
Mount the control box near to the indoor unit in a visible location
Mount the remote sensor assembly low down in the room. Maximum height from the floor surface should be 300mm. Ensure 500mm clearance around the sensor
Connect the remote sensor assembly to the control box using a 6 core cable
Connect the control box to a fused 240V AC 1amp supply
For RAV units connect the FCU interface cable to CN17 on the indoor PCB
For MM units connect the FCU interface cable to CN21 on the indoor PCB
RBC-RD1-PE

12. Refrigerant Detection Electrical Installation RBC-RD2-PE
Mount the control box inside the compressor housing of the outdoor unit
Connect a 3-core supply cable from the control unit to the electrical box on the outdoor unit. Ensure a 1A fuse is fitted
If one outdoor unit is used connect the CDU interface cable from the control unit to the electrical box on the outdoor unit.
Locate the 3 ceramic fuses at the top of the electrical box
From the top fuse remove the small red cable from the right side of the fuse. In its place fit the CDU interface cable
From the small red cable removed from the ceramic fuse place into the crimp butt joint and crimp firmly

13. Refrigerant Detection Electrical Installation RBC-RD2-PE
For multiple outdoor units, each refrigerant detector must be connected in series to the unit in the inverter outdoor unit. The CDU interface cable is only used in the inverter unit
Connect each refrigerant detector using 3-core cable to the L1, N and earth terminals in each CDU. Each detector must be protected by a 1amp 240VAC fuse
Connect the AI terminals in the control units as shown in the diagram
To complete the series circuit connect the CDU interface cable to the inverter electrical box as described in the previous slide
RBC-RD1-PE

14. Refrigerant Detection System Operation
Low Level Alarm – 250ppm (RBC-RD1-PE Only):
When the low level alarm limit is reached:
The Detector Active LED will be “ON”
The amber Low Level Alarm LED will start flashing
After 10 minutes, the Low Level Alarm LED will stop flashing and remain “ON”
B5 fault code will be generated by the indoor unit
The indoor unit will not shut down
RBC-RD1-PE
Note: If the refrigerant concentration drops below 250ppm the control box will self reset

15. Refrigerant Detection System Operation
High Level Alarm – 1000ppm (RBC-RD1/RD2-PE):
When the high level alarm limit is reached:
The Detector Active and the Low Level Alarm LED’s will be “ON”
The red High Level Alarm LED will start flashing
After 10 minutes, the High Level Alarm LED will stop flashing and remain “ON”. The red Shutdown LED will also come “ON”
B5 & B6 fault codes will be generated by the indoor unit, 04 fault code will be generated by the outdoor unit
The indoor unit will shut down and the audible alarm will sound if an RD1 was activated
The outdoor unit will shut down if an RD2 was activated
The alarm volt free contacts will operate to control any suitable external device
RBC-RDx-PE
Note: The system must be manually reset using the reset buttons on the control box

16. Refrigerant Detection System Operation
Spill Alarm – 2200ppm (RBC-RD1/RD2-PE)
When the spill alarm limit is reached:
The Detector Active LED will be “ON”
After 10 seconds at the Spill Alarm limit, the Shutdown LED will come “ON” The Low Level Alarm & the High Level Alarm LED’s will start flashing
B6 fault code will be generated by the indoor unit if the refrigerant is detected in the room by RBC-RD1-PE
04 fault code will be generated by the outdoor unit if the refrigerant is detected in the compressor housing by RBC-RD2-PE
The indoor unit will shut down and the audible alarm will sound if an RD1 was activated
The outdoor unit will shut down if an RD2 was activated
The “alarm” volt free contacts will operate to control any suitable external device connected to the control box
RBC-RDx-PE
Note: The system must be manually reset using the reset buttons on the control box

17. Refrigerant Detection System Operation
Sensor Failure (RBC-RD1/RD2-PE)
When the refrigerant sensor fails:
After 1 minute the Detector Active LED will go “OFF”, and the Low Level Alarm LED will come “ON”
B5 fault code will be generated by the indoor unit. No fault code will be generated by the outdoor unit. The indoor or outdoor unit will not shut down
After 4 hours the Low Level Alarm LED will go “OFF” and the Shutdown LED will come “ON”
B6 fault code will be generated by the indoor unit if the refrigerant leak is detected in the room by RBC-RD1-PE
A 04 fault code will be generated by the outdoor unit if the refrigerant is detected in the compressor housing by RBC-RD2-PE
The indoor or outdoor unit will shutdown
The “alarm” volt free contacts will operate to control any suitable external device connected to the control box
RBC-RDx-PE
Note: The system must be manually reset using the reset buttons on the control box after replacing the sensor

18. Refrigerant Detection Refrigerant Mass Required
RBC-RD1-PE : High Level Alarm
Calculation based on a hotel room 5m x 8m x 2.5m.
Density of R407C vapour at ambient pressure = 3.518kg/m3.
For high level alarm (unit shutdown) at 1000ppm: Ppm concentration = 1000/ = 0.001
Grams of R407C = 5m x 8m x 2.5m x 3.518kg/m3 x ppm/conc
= kg
= 352 g
RBC-RD1-PE : Low Level Alarm
Grams of R407C = 5m x 8m x 2.5m x 3.518kg/m3 x ppm/conc
= kg
= 88 g
RBC-RD1-PE

19. Refrigerant Detection Refrigerant Mass Required
RBC-RD2-PE : High Level Alarm
Calculation based on the volume of the compressor housing = 0.8m3
Density of R407C vapour at ambient pressure = 3.518kg/m3.
For high level alarm (unit shutdown) at 1000ppm:
Ppm concentration = 1000/
= 0.001
Grams of R407C = 0.8m3 x 3.518kg/m3 x ppm/conc
= kg
= 2.8 g
RBC-RD2-PE

20. Refrigerant Detection Installation Indoor / Outdoor
Indoor Installation
Standard Grid Plate (BS 57533:1995)
Standard Front Plate
Integral audible alarm mute button
and refrigerant sensor
RBC-RD1-PE

21. Refrigerant Detection Installation Indoor / Outdoor
Outdoor Installation
RBC-RD2-PE only available with
MMS
RBC-RD2-PE

22. Fault Display Panel
Fault Display Panel
RBC-FDP1-PE

23. Fault Display Panel Contents
Features
Installation

24. Fault Display Panel Features
Detect all Indoor Units faults
Attached in parallel with the Remote Controller (ABC)
LED to indicate activity (flashing at 1s rate)
LED to indicate fault / no fault
Volt-free contact allows external
signalling of the fault
Relay closed under fault free conditions
09 Fault can be optionally filtered
RBC-FDP1-PE

25. Fault Display Panel Installation
No external power supply needed
as it is attached in parallel with
the Remote Controller (ABC).
Fault filter
OFF: 09 faults are treated like any other fault code
ON: 09 faults are only reported after 3 hours
RBC-FDP1-PE

26. Central Remote Controller
RBC-CR1-PE, RBC-CR64-PE

27. Central Remote Controller Contents
Models
Features / Options
Installation

28. Central Remote Controller Models Available
RBC-CR1-PE
Control up to 16 Indoor Units
RBC-CR64-PE
Control up to 64 Indoor Units
RBC-CRx-PE
Note: RBC-CRx-PE cannot be used in conjunction with the Windows Gateway (WG1)

29. Central Remote Controller Options Available
RBC-CR1-PE / RBC-CR64-PE
Compatible with Toshiba MMS and 4 Series Heat Pump
Compatible with 7 Day Timer (RBC-WT1-PE)
RBC-CR64-PE
External switch (Input Shutdown)
External timer
Units can be grouped in Zones
Two central Controllers can be used on the same XY Network
RBC-CRx-PE
Note: RBC-CRx-PE cannot be used in conjunction with the Windows Gateway (WG1)

30. Central Remote Controller Installation (RBC-CR64-PE)
All types of systems (MMS, SMi, Single split) can be connected to the same Central Remote Controller
RBC-CR64-PE
Note: RBC-CR64-PE cannot be used in conjunction with the Windows Gateway (WG1)

31. Interactive Intelligence
Building Management System
RBC-WG1-PE, RBC-WP1-PE,
RBC-EM1-PE, RBC-IK1-PE

32. Interactive Intelligence BMS - Contents
Link Between Products
Windows Gateway
Windows Software
Energy Monitoring
Internet Kit
Note: RBC-WG1-PE, RBC-WP1-PE, RBC-EM1-PE, RBC-IK1-PE

33. Interactive Intelligence Link Between Product ?
Internet / Intranet

34. Link Between Controls Product Windows Gateway 1:64
To control up to 64 Toshiba I./D (MMS or RAV AI) units
Consists of:
One Gateway
One IEC Plug
Installation Instruction
with functional profile
RBC-WG1-PE
Note: RBC-WG1-PE cannot be used in conjunction with any other Central Controller

35. Link Between Controls Product Windows Software 1:1024
To manage on one PC up to 1024 I/D i.e. 16 Gateways
Consists of:
One CD “Interactive
Intelligence”
One hardware key
One owner's manual
PCI Card (Extension)
RBC-WG1-PE
Note: RBC-WG1-PE cannot be used in conjunction with any other Central Controller

36. Link Between Controls Product Energy Monitoring
RBC-EM1-PE is an add-on to RBC-WP1-PE
Consists of:
One power meter
Current Transformers x3
Installation Instructions
RBC-EM1-PE
Note: RBC-EM1-PE must be used in conjunction with RBC-WG1-PE, RBC-WP1-PE

37. Link Between Controls Product Internet Kit 1:5
RBC-IK1-PE is an add-on to RBC-WP1-PE
Consists of:
One key file CD
“Interactive Intelligence”
License for 5
concurrent users
RBC-WP1-PE
Note: RBC-IK1-PE must be used in conjunction with RBC-WG1-PE, RBC-WP1-PE

38. Interactive Intelligence
Windows Gateway
RBC-WG1-PE

39. Interactive Intelligence Windows Gateway 1:64
Gateway using LonWorks Technology
Control up to to 64 I/D
Auto Detect number of I/D automatically
Functions of Central Remote Controller
Ambient & Coil Temperatures available
RBC-WG1-PE
Note: RBC-WG1-PE is not compliant with Echelon.

40. Interactive Intelligence
Windows Software
Interactive Intelligence
RBC-WP1-PE

41. Interactive Intelligence Windows Software 1:1024 Contents
Features
Installation
Navigation (Schematics)
Alarms
Remote Connection
Timed Operation and Optimised Start
Frost Protection Module
Data Logging
Graphical view
Backup / Restore of the complete System
Customisation of Schematics
Website

42. Interactive Intelligence Features
Automated Configuration
Display and retransmission of Intelligent fault code
Unit location can be displayed on PC
Data and alarms logging
Timed operation under several schedule
Navigator (schematics) fully customisable
Hardware key protection and 100 access level configurable
RBC-WP1-PE
Note: Compatible with Win 98 SE, Win NT 4.0, Win 2000 and Win XP.

43. Interactive Intelligence Automatic Installation
BEFORE:
LonMaker / Front End Software
PC & PCLTA20
Systems Integrator
AFTER:
Interactive Intelligence PC
RBC-WP1-PE

44. Interactive Intelligence Automatic Installation
Auto-detect of the number of units on each Windows Gateway
Auto-detect how many Gateways on the network
Auto-detect how many Power Meters if any are present
Generates a Network database
Generates standard schematics for each units
RBC-WP1-PE
Note: The XY network connection must be checked.

45. Interactive Intelligence Automatic Installation
Opening system
Create schematics ?
RBC-WP1-PE

46. Interactive Intelligence Automatic Installation
Commissioned Devices ?
(Windows Gateway /
Power Meter)
Software looking for
devices (Commissioned /
Decommissioned)
RBC-WP1-PE

47. Interactive Intelligence Automatic Installation
Database generated
Able to rename Gateways
Able to rename Indoor Units
Able to decommission Gateways
(right click on the Gateway)
RBC-WP1-PE

48. Interactive Intelligence Navigation / Schematics
Level 1 Schematic
Number of
Gateways
Click here to go to
Level 2 (I/D
attached to this
Gateway)
RBC-WP1-PE
Note: LEVEL 1 Schematic

49. Interactive Intelligence Navigation / Schematics
Level 2 Schematic
Number of
Indoor Units
Click here to go to
Level 3 (details of
the settings)
RBC-WP1-PE
Note: LEVEL 2 Schematic

50. Interactive Intelligence Navigation / Schematics
Level 3 Schematic
Settings of the
Indoor Unit
Able to change the
picture of the Indoor
Unit
RBC-WP1-PE
Note: LEVEL 3 Schematic

51. Interactive Intelligence Navigation / Schematics
All models
RBC-WP1-PE
Note: LEVEL 3 Schematic

52. Interactive Intelligence Alarms
Indication:
Intelligent FaultCode
Gateway/Indoor Unit
RBC-WP1-PE

53. Interactive Intelligence Alarms
Transmission
Print
Audio
Popup Window
Retransmission:
Fax
Remote Site
GSM / Pager
RBC-WP1-PE
Note: Modem Internal / External Required on Supervisor.

54. Interactive Intelligence Remote Connection
Internet Kit
Site: RBC-WP1-PE + RBC-IK1-PE
Office: Internet Explorer
Remote Connection:
Site: RBC-WP1-PE
Office: RBC-WP1-PE
Site Office
WP1 / IK1 IE
RBC-WP1-PE RBC-WP1-PE
RBC-WP1-PE
Note: Modem Internal / External Required on Supervisor.

55. Interactive Intelligence Remote Connection
Able to:
Access system set-up
Edit / Modify schematics
Not able to access:
Driver set-up
Any plug-in (Optimised Start, Frost
Protection Module, Energy Monitoring)
RBC-WP1-PE
Note: Modem Internal / External Required on Supervisor.

56. Interactive Intelligence Timer – Option 1: Local Calendar
Weekly Schedule
300 Items
24 Events in a day
Special Day
RBC-WP1-PE
Note: Local Calendar Option.

57. Interactive Intelligence Timer – Option 2: Optimised Start
Weekly Schedule
RBC-WP1-PE
Note: Optimised Start Option.

58. Interactive Intelligence Timer – Option 2: Optimised Start
Weekly Schedule
Optimised Start Option
User Friendly set-up
RBC-WP1-PE
Note: Optimised Start Option.

59. Interactive Intelligence Timer – Option 2: Optimised Start
Enable a specific
Temperature to be achieved
at a specific time
Learning the room inertia to
determine when to start the
Air Conditioning system
23 °C
20 °C
Setpoint
08: : : time
DAY 1
DAY 2
DAY 3
RBC-WP1-PE
Note: Optimised Start Option.

60. Interactive Intelligence Frost Protection Module
Can enable the A/C and maintain in constant temperature in the event of low temperature being detected
Can stop the A/C when a temperature is achieved
Able to:
Turn On / Off
Change the Set Point
Change the Mode
Conditions can be entered which includes samples times, the trigger and reset points.
RBC-WP1-PE

61. Interactive Intelligence Data Logging
Record any data
SetPoint
Mode
Fan Speed
On / Off
Fault Codes
Demand Data
TA, TC
RBC-WP1-PE
Note: Max Log Time Base = 1 Day.

62. Interactive Intelligence Graphical View
Graphics from
Data logging
Colours and type of
Graphic customisable
Zoom In / Out
Print
RBC-WP1-PE

63. Interactive Intelligence Backup the complete system
Backup system
Notes
Basic Configuration
Schematics
Data logging
Local Calendars
Script
RBC-WP1-PE

64. Interactive Intelligence Restore the complete system
Restore system
Notes
Basic Configuration
Schematics
Data logging
Local Calendars
Script
RBC-WP1-PE

65. Interactive Intelligence Customisation
Site fully customisable
Examples:
United Kingdom Plymouth - Life Test
United Kingdom Leatherhead – UTC House Life Test
United Kingdom Glasgow – Airbels Road
France Nantes - System U
Austria – Office
Diagnostics (16 I/D and 32 I/D)
RBC-WP1-PE

66. Interactive Intelligence Customisation – UK - Plymouth
Level 1 Schematic
4 Gateways
8 Different Systems
RBC-WP1-PE

67. Interactive Intelligence Customisation – UK - Plymouth
Level 2 Schematic
MMS14HP
Energy Consumption
available
RBC-WP1-PE

68. Interactive Intelligence Customisation – UK - Plymouth
Level 2 Schematic
SMI10HP
Top view imported
from AutoCAD
RBC-WP1-PE

69. Interactive Intelligence Customisation – UK - Leatherhead
Level 1 Schematic
UTC House
RBC-WP1-PE

70. Interactive Intelligence Customisation – UK - Leatherhead
Level 2 Schematic
Top view imported
from AutoCAD
Blue and Red button
to specify if the I./D
is cooling or heating
RBC-WP1-PE

71. Interactive Intelligence Customisation – UK - Leatherhead
Level 2 Schematic
Only available for
Service Engineers
RBC-WP1-PE

72. Interactive Intelligence Customisation – UK - Leatherhead
Level 2 Schematic
Outdoor view
imported from
AutoCAD
RBC-WP1-PE

73. Interactive Intelligence Customisation – UK – AirbelsRoad
Level 1 Schematic
2 Gateways
Trend System
(Ventilation, hot water
air handling plant,
water levels, metering)
RBC-WP1-PE

74. Interactive Intelligence Customisation – UK – AirbelsRoad
Level 2 Schematic
Gateway Ground &
First floor
I/D Fault Codes
RBC-WP1-PE

75. Interactive Intelligence Customisation – UK – AirbelsRoad
Level 2 Schematic
Gateway First &
Second floor
I/D Fault Codes
RBC-WP1-PE

76. Interactive Intelligence Customisation – UK – AirbelsRoad
Trend Control
Fan
Heaters
Water Tank
Metering
RBC-WP1-PE

77. Interactive Intelligence Customisation – UK – AirbelsRoad
Air Handling Unit
Global view
RBC-WP1-PE

78. Interactive Intelligence Customisation – UK – AirbelsRoad
Extract Fan
Global view
RBC-WP1-PE

79. Interactive Intelligence Customisation – UK – AirbelsRoad
Heaters
Global view
RBC-WP1-PE

80. Interactive Intelligence Customisation – UK – AirbelsRoad
Metering
RBC-WP1-PE

81. Interactive Intelligence Customisation – FR - Nantes
Level 1
Schematic
Building view
3 Gateways
150 I/D
RBC-WP1-PE

82. Interactive Intelligence Customisation – FR - Nantes
Level 2 Schematic
Top view imported
from AutoCAD
TS, TA reading
Heat / Cool reading
RBC-WP1-PE

83. Interactive Intelligence Customisation – FR - Nantes
Special Schematic
Top view imported
from AutoCAD
Outdoor view
Display outdoor
faults
RBC-WP1-PE

84. Interactive Intelligence Customisation – AT - Adelsberger
Level 2 Schematic
Complete view of the
system
Temperatures reading
from LonWorks sensors
Ventilation controlled
with Interactive Intelligence
I/D will stop if ventilation
off
RBC-WP1-PE

85. Interactive Intelligence Customisation – Diagnostics 16
Special
Schematic
Able to see
I/D data:
01 to 16
17 to 38
39 to 48
49 to 64
RBC-WP1-PE

86. Interactive Intelligence Customisation – Diagnostics 32
Special
Schematic
Able to see
all the data from
the Gateway
RBC-WP1-PE

87. Interactive Intelligence Website - Home
Home (basic
feature of
Interactive
Intelligence)
RBC-WP1-PE

88. Interactive Intelligence Website -Updates
LNS Driver
RGM
NDS
OZM
FPM
Node Utility
Checklist
RBC-WP1-PE

89. Interactive Intelligence Website - FAQ
Commissioning…
RBC-WP1-PE

90. Interactive Intelligence
Energy Monitoring
RBC-EM1-PE

91. Energy Monitoring Contents
Features
Installation of Power Meter
Set-up the system
View data
Set-up the report
RBC-EM1-PE

92. Energy Monitoring Features
Automatic Power Meter configuration
Calculation of Unit Running costs per indoor unit and system
Running costs based on a multiple tariffs
Running report based with different clients
Option for data export to CSV file
(Compatible with Excel)
One Power Meter for one Outdoor Unit
RBC-EM1-PE
Note: Possibility to connect one Power Meter to 2 MMS Outdoor Units.

93. Energy Monitoring Installation of Power Meter
Installation 1: MMS14HP
Inverter Power Meter
Fix Power Meter
Current Transformer x 3
RBC-EM1-PE

94. Energy Monitoring Installation of Power Meter
Installation 2: MMS26HP
Inverter Power Meter
Fix Power Meter
(1 Power Meter for 2 Fix Speed)
Current Transformer x 3
RBC-EM1-PE

95. Energy Monitoring Installation of Power Meter
Installation 3: SMI10HP
Inverter Power Meter
Current Transformer x 3
RBC-EM1-PE

96. Energy Monitoring Set-up the system
Set-up the database
Data Tree
System
Power Meter
Indoor Units
RBC-EM1-PE

97. Energy Monitoring Set-up the system
Set-up Power Meters
and Indoor Units
Link with LonWorks
database
Model names
RBC-EM1-PE

98. Energy Monitoring View Data
System data:
Indoor Unit 1
Indoor Unit 2
Indoor Unit 3
Indoor Unit 4 …
RBC-EM1-PE

99. Energy Monitoring Set-up the report
Select:
Client
Tariff
Layout
Destination ( or
Printer)
Link (System)
Select Indoor Unit
RBC-EM1-PE

100. Energy Monitoring Set-up the report
View the report:
Toshiba Standard
Report with:
Client
Date
System reference
RBC-EM1-PE

101. Energy Monitoring Set-up the report
Modify the report:
Able to change the
complete layout
Able to import
pictures
RBC-EM1-PE

102. Interactive Intelligence
Internet Kit
RBC-IK1-PE

103. Internet Kit Internet Kit is a license which enables a plug-in
Get connected to server
using Internet Explorer
No software need to be
installed on the client PC
Click HERE
RBC-IK1-PE
Note: The license is for 5 concurrent users.

104. Internet Kit 2 Levels of Access: Remote A/C system monitoring
Full remote A/C
system control and
RBC-IK1-PE
Note: The license is for 5 concurrent users.

105. Internet Kit
Internet Kit does not allow to modify the system set-up of Interactive Intelligence
5 concurrent users can be connected in the same time
Each user can be allocated their own unique schematic
Alarms can be viewed remotely
RBC-IK1-PE
Note: The license is for 5 concurrent users.

106. Interactive Intelligence
Any questions ?
Internet / Intranet

107. Interactive Intelligence Putting you in Control…
Thanks for
your time…
Controls
Sebastien Desmottes - Controls Development Engineer @ Plymouth (UK)

108. Interactive Intelligence Putting you in Control…
In Touch with Tomorrow
TOSHIBA
Controls
Sebastien Desmottes - Controls Development Engineer @ Plymouth (UK)