1. © 1999, Cisco Systems, Inc. 7-1 Chapter 7 Extending Switched Networks with Virtual LANs

2. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-2 Objectives Upon completion of this chapter, you will be able to perform the following tasks: Configure a VLAN Configure VLAN Trunking Protocol (VTP) Configure a switch for trunking Verify VLAN connectivity Verify spanning-tree operations

3. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-3 VLAN Overview Segmentation Flexibility Security 3rd floor 2nd floor 1st floor SALESHRENG A VLAN = A broadcast domain = Logical network (subnet)

4. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-4 VLAN Operations Switch A Green VLAN Black VLAN Red VLAN Each logical VLAN is like a separate physical bridge

5. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-5 VLAN Operations Switch A Green VLAN Black VLAN Red VLAN Switch B Green VLAN Black VLAN Red VLAN Each logical VLAN is like a separate physical bridge VLANs can span across multiple switches

6. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-6 VLAN Operations Switch A Green VLAN Black VLAN Red VLAN Switch B Green VLAN Black VLAN Red VLAN Trunk Each logical VLAN is like a separate physical bridge VLANs can span across multiple switches Trunks carries traffic for multiple VLANs Fast Ethernet

7. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-7 VLAN Membership Modes VLAN5 Static VLANDynamic VLAN MAC = 1111.1111.1111 Trunk VMPS 1111.1111.1111 = vlan 10 VLAN10 Port e0/9 Port e0/4

8. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-8 ISL Tagging Performed with ASIC Not intrusive to client stations, client does not see the ISL header Effective between switches, routers and switches, switches and servers with ISL network interface cards ISL trunks enable VLANs across a backbone VLAN Tag added by incoming port VLAN Tag stripped by forwarding port Inter-Switch Link carries VLAN identifier

9. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-9 ISL Encapsulation ISL Header 26 bytes Encapsulated Ethernet frame CRC 4 bytes Frames encapsulated with ISL header and CRC Support for many VLANs (1024) VLAN field BPDU bit DATypeUserSALEN VLAN AAAA03 BPDU HSAVLAN BPDU INDEXRES

10. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-10 VLAN Trunking Protocol (VTP) A messaging system that advertises VLAN configuration information Maintains VLAN configuration consistency throughout a common administrative domain VTP sends advertisements on trunk ports only Support mixed media trunks (Fast Ethernet, FDDI, ATM) 1.“new vlan added” 3.Sync to the latest vlan information 2 VTP Domain “ICND”

11. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-11 VTP Modes Server Client Transparent Sends/forwards advertisements Synchronize Not saved in NVRAM Create vlans Modify vlans Delete vlans Sends/forwards advertisements Synchronize Saved in NVRAM Create vlans Modify vlans Delete vlans Forwards advertisements Does not synchronize Saved in NVRAM

12. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-12 How VTP Works VTP advertisements are sent as multicast frames VTP servers and clients synchronized to latest revision number VTP advertisement are sent every five minutes or when there is a change

13. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-13 VTP advertisements are sent as multicast frames VTP servers and clients synchronized to latest revision number VTP advertisement are sent every five minutes or when there is a change How VTP Works 1.Add new VLAN 2.Rev 3 --> Rev 4 Server Client 4.Rev 3 --> Rev 4 5.Sync new vlan info 33 4.Rev 3 --> Rev 4 5.Sync new vlan info

14. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-14 VTP Pruning Increases available bandwidth by reducing unnecessary flooded traffic Example: Station A sends broadcast, broadcast is only flooded toward any switch with ports assigned to the red VLAN Switch 4 Switch 2 Switch 6Switch 3Switch 1 Port 2 Flooded traffic is pruned Red VLAN Port 1 Switch 5 A B

15. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-15 VLAN Configuration Guidelines Maximum number of VLANs is switch-dependent Catalyst 1900 supports 64 VLANs with a separate spanning tree per VLAN VLAN1 is One of the factory default VLANs CDP and VTP advertisements are sent on VLAN1 Catalyst 1900 IP address is in the VLAN1 broadcast domain Must be in VTP server or transparent mode to create, add, or delete VLANs

16. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-16 VLAN Configuration Steps Enable VTP (optional) Enable trunking Create VLANs Assign VLAN to ports

17. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-17 VTP domain name VTP mode (server/client/transparent)—VTP server mode is the default VTP pruning VTP password VTP trap VTP Configuration Guidelines Use caution when adding a new switch into an existing domain. A new switch should be added in client mode to prevent the new switch from propagating incorrect VLANs information Use the delete vtp command to reset the VTP revision number

18. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-18 Creating a VTP Domain vtp [server | transparent] [domain domain-name] [trap {enable | disable}] [password password] [pruning {enable | disable} wg_sw_a(config)#

19. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-19 Creating a VTP Domain wg_sw_a#conf terminal Enter configuration commands, one per line. End with CNTL/Z wg_sw_a(config)#vtp transparent wg_sw_a(config)#vtp domain switchlab vtp [server | transparent] [domain domain-name] [trap {enable | disable}] [password password] [pruning {enable | disable} wg_sw_a(config)#

20. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-20 Verifying VTP Configurations wg_sw_a#show vtp

21. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-21 Verifying VTP Configurations wg_sw_a#show vtp VTP version: 1 Configuration revision: 4 Maximum VLANs supported locally: 1005 Number of existing VLANs: 6 VTP domain name : switchlab VTP password : VTP operating mode : Transparent VTP pruning mode : Enabled VTP traps generation : Enabled Configuration last modified by: 10.1.1.40 at 00-00-0000 00:00:00 wg_sw_a#show vtp

22. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-22 Defining a Trunk trunk [on | off | desirable | auto | nonegotiate] wg_sw_a(config-if)# On = Set trunk on and negotiate with other side Off = Set trunk off and negotiate with other side Desirable = Negotiate with other side. Trunk on if other side is on, desirable, or auto Auto = Will be a trunk only if the other side is on or desirable Non-negotiate = Set trunk on and will not negotiate

23. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-23 Defining a Trunk wg_sw_a#conf terminal Enter configuration commands, one per line. End with CNTL/Z wg_sw_a(config)#interface f0/26 wg_sw_a(config-if)#trunk on First trunk port(Port A) On = Set trunk on and negotiate with other side Off = Set trunk off and negotiate with other side Desirable = Negotiate with other side. Trunk on if other side is on, desirable, or auto Auto = Will be a trunk only if the other side is on or desirable Non-negotiate = Set trunk on and will not negotiate trunk [on | off | desirable | auto | nonegotiate] wg_sw_a(config-if)#

24. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-24 Verifying a Trunk wg_sw_a#show trunk [A | B]

25. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-25 Verifying a Trunk wg_sw_a#show trunk a DISL state: On, Trunking: On, Encapsulation type: ISL wg_sw_a#show trunk [A | B]

26. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-26 Adding a VLAN vlan vlan# [name vlan-name] wg_sw_a(config)#

27. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-27 Adding a VLAN wg_sw_a#conf terminal Enter configuration commands, one per line. End with CNTL/Z wg_sw_a(config)#vlan 9 name switchlab2 vlan vlan# [name vlan-name] wg_sw_a(config)#

28. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-28 Verifying a VLAN wg_sw_a#show vlan [vlan#]

29. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-29 Verifying a VLAN wg_sw_a#sh vlan 9 VLAN Name Status Ports ------------------------------------------------- 9 switchlab2 Enabled ------------------------------------------------- VLAN Type SAID MTU Parent RingNo BridgeNo Stp Trans1 Trans2 ------------------------------------------------------------------------------------------------------- 9 Ethernet 100009 1500 0 1 1 Unkn 0 0 -------------------------------------------------------------------------------------------------------- wg_sw_a#show vlan [vlan#]

30. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-30 Modifying a VLAN Name vlan vlan# name vlan-name wg_sw_a#conf terminal Enter configuration commands, one per line. End with CNTL/Z wg_sw_a(config)#vlan 9 name switchlab90 wg_sw_a#show vlan 9 VLAN Name Status Ports ------------------------------------------------ 9 switchlab90 Enabled ------------------------------------------------ wg_sw_a(config)#

31. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-31 Assigning Switch Ports to a VLAN vlan-membership {static {vlan#} | dynamic} wg_sw_a(config-if)#

32. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-32 Assigning Switch Ports to a VLAN wg_sw_a#conf terminal Enter configuration commands, one per line. End with CNTL/Z wg_sw_a(config)#interface ethernet 0/8 wg_sw_a(config-if)#vlan-membership static 9 vlan-membership {static {vlan#} | dynamic} wg_sw_a(config-if)#

33. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-33 Verifying VLAN Membership wg_sw_a#show vlan-membership

34. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-34 Verifying VLAN Membership wg_sw_a#show vlan-membership Port VLAN Membership Type Port VLAN Membership Type -------------------------------------------- ----------------------------------------- 1 5 Static 13 1 Static 2 1 Static 14 1 Static 3 1 Static 15 1 Static 4 1 Static 16 1 Static 5 1 Static 17 1 Static 6 1 Static 18 1 Static 7 1 Static 19 1 Static 8 9 Static 20 1 Static Note: port 1=e0/1, port 2=e0/2..... wg_sw_a#show vlan-membership

35. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-35 Verifying Spanning Tree wg_sw_a#show spantree {vlan number}

36. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-36 Verifying Spanning Tree wg_sw_a#show spantree 1 VLAN1 is executing the IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, address 0050.F037.DA00 Configured hello time 2, max age 20, forward delay 15 Current root has priority 0, address 00D0.588F.B600 Root port is FastEthernet 0/26, cost of root path is 10 Topology change flag not set, detected flag not set Topology changes 53, last topology change occured 0d00h17m14s ago Times: hold 1, topology change 8960 hello 2, max age 20, forward delay 15 Timers: hello 2, topology change 35, notification 2 Port Ethernet 0/1 of VLAN1 is Forwarding Port path cost 100, Port priority 128 Designated root has priority 0, address 00D0.588F.B600 Designated bridge has priority 32768, address 0050.F037.DA00 Designated port is Ethernet 0/1, path cost 10 Timers: message age 20, forward delay 15, hold 1 wg_sw_a#show spantree {vlan number}

37. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-37 Visual Objective core_ server 10.x.x.1 wg_sw_a 10.1.1.10 wg_sw_l 10.1.1.120 wg_pc_a 10.2.2.12 wg_pc_l 10.13.13.12... e0/1 fa0/26 (port A) e0/1 fa0/26 (port A) fa0/1fa0/12 fa0/24 core_sw_a 10.1.1.2 ISL SUBNETVLANPOD 10.1.1.01wg_ro_x, wg_sw_x, core_sw_a 10.2.2.02wg_pc_a, core_server 10.3.3.03wg_pc_b, core_server 10.4.4.04wg_pc_c, core_server 10.5.5.05wg_pc_d, core_server 10.6.6.06wg_pc_e, core_server 10.7.7.07wg_pc_f, core_server 10.8.8.0 8 wg_pc_g, core_server 10.9.9.09wg_pc_h, core_server 10.10.10.010wg_pc_i, core_server 10.11.11.011wg_pc_j, core_server 10.12.12.012wg_pc_k, core_server 10.13.13.013wg_pc_l, core_server VLAN2 VLAN13 wg_ro_a 10.1.1.11 e0/2e0 wg_ro_l 10.1.1.121 e0e0/2

38. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-38 Visual Objective core_ server wg_sw_a 10.1.1.10 wg_sw_l 10.1.1.120... e0/1 fa0/26 (port A) e0/1 fa0/26 (port A) fa0/1 fa0/12 fa0/24 core_sw_a 10.1.1.2 core_sw_b 10.1.1.4 fa0/12 fa0/1 fa0/13 fa0/27 (port B) fa0/27 (port B) wg_pc_a 10.2.2.12 wg_pc_l 10.13.13.12 ISL 10.x.x.1 VLAN2 VLAN13 SUBNETVLANPOD 10.1.1.01wg_ro_x, wg_sw_x, core_sw_a, core_sw_b 10.2.2.02wg_pc_a, core_server 10.3.3.03wg_pc_b, core_server 10.4.4.04wg_pc_c, core_server 10.5.5.05wg_pc_d, core_server 10.6.6.06wg_pc_e, core_server 10.7.7.07wg_pc_f, core_server 10.8.8.0 8 wg_pc_g, core_server 10.9.9.09wg_pc_h, core_server 10.10.10.010wg_pc_i, core_server 10.11.11.011wg_pc_j, core_server 10.12.12.012wg_pc_k, core_server 10.13.13.013wg_pc_l, core_server fa0/14...

39. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-39 Summary After completing this chapter, you should be able to perform the following tasks: Configuring VLAN Configuring VTP Configuring a trunk Verifing Spanning Tree Operations

40. © 1999, Cisco Systems, Inc. www.cisco.com ICND—7-40 Review Questions 1. What are the three VTP modes? 2. Over what type of port can VTP advertisements be sent? 3. VLAN ID is carried in the ________ header. 4. How do we assign a VLAN to a port?