1. Transmission Line “Definition” General transmission line: a closed system in which power is transmitted from a source to a destination Our class: only TEM mode transmission lines A two conductor wire system with the wires in close proximity, providing relative impedance, velocity and closed current return path to the source. Characteristic impedance is the ratio of the voltage and current waves at any one position on the transmission line Propagation velocity is the speed with which signals are transmitted through the transmission line in its surrounding medium.

2. Presence of Electric and Magnetic Fields Both Electric and Magnetic fields are present in the transmission lines These fields are perpendicular to each other and to the direction of wave propagation for TEM mode waves, which is the simplest mode, and assumed for most simulators(except for microstrip lines which assume “quasi-TEM”, which is an approximated equivalent for transient response calculations). Electric field is established by a potential difference between two conductors. Implies equivalent circuit model must contain capacitor. Magnetic field induced by current flowing on the line Implies equivalent circuit model must contain inductor.

3. General Characteristics of Transmission Line Propagation delay per unit length (T 0 ) { time/distance} [ps/in] Or Velocity (v 0 ) {distance/ time} [in/ps] Characteristic Impedance (Z 0 ) Per-unit-length Capacitance (C 0 ) [pf/in] Per-unit-length Inductance (L 0 ) [nf/in] Per-unit-length (Series) Resistance (R 0 ) [  /in] Per-unit-length (Parallel) Conductance (G 0 ) [S/in] T-Line Equivalent Circuit lL 0 lR 0 lC 0 lG 0 lL 0 lR 0 lC 0 lG 0

4. Ideal T Line Ideal (lossless) Characteristics of Transmission Line Ideal TL assumes: Uniform line Perfect (lossless) conductor (R 0  0) Perfect (lossless) dielectric (G 0  0) We only consider T 0, Z 0, C 0, and L 0. A transmission line can be represented by a cascaded network (subsections) of these equivalent models. The smaller the subsection the more accurate the model The delay for each subsection should be no larger than 1/10 th the signal rise time. lL 0 lC 0 lL 0 lC 0

5. Signal Frequency and Edge Rate vs. Lumped or T line Models In theory, all circuits that deliver transient power from one point to another are transmission lines, but if the signal frequency(s) is low compared to the size of the circuit (small), a reasonable approximation can be used to simplify the circuit for calculation of the circuit transient (time vs. voltage or time vs. current) response.

6. T Line Rules of Thumb Td <.1 Tx Td <.4 Tx May treat as lumped Capacitance Use this 10:1 ratio for accurate modeling of transmission lines May treat as RC on-chip, and treat as LC for PC board interconnect So, what are the rules of thumb to use?

7. Other “Rules of Thumb” Frequency knee (Fknee) = 0.35/Tr (so if Tr is 1nS, Fknee is 350MHz) This is the frequency at which most energy is below Tr is the 10-90% edge rate of the signal Assignment: At what frequency can your thumb be used to determine which elements are lumped? Assume 150 ps/in

8. When does a T-line become a T-Line? Whether it is a bump or a mountain depends on the ratio of its size (tline) to the size of the vehicle (signal wavelength) When do we need to use transmission line analysis techniques vs. lumped circuit analysis? Tline Wavelength/edge rate Similarly, whether or not a line is to be considered as a transmission line depends on the ratio of length of the line (delay) to the wavelength of the applied frequency or the rise/fall edge of the signal

9. Equations & Formulas How to model & explain transmission line behavior

10. Relevant Transmission Line Equations Propagation equation Characteristic Impedance equation In class problem: Derive the high frequency, lossless approximation for Z0  is the attenuation (loss) factor  is the phase (velocity) factor

11. Ideal Transmission Line Parameters Knowing any two out of Z 0, T d, C 0, and L 0, the other two can be calculated. C 0 and L 0 are reciprocal functions of the line cross- sectional dimensions and are related by constants:  is electric permittivity  0 = 8.85 X 10 -12 F/m (free space)  r i s relative dielectric constant  is magnetic permeability  0 = 4p X 10 -7 H/m (free space)  r is relative permeability.; ;; 1 ;; ;; 00 000 000 0 0 0 00d 0 0 0   rr LCv TZL Z T C CLT C L Z     Don’t forget these relationships and what they mean!

12. Parallel Plate Approximation Assumptions TEM conditions Uniform dielectric (  ) between conductors T C > T D T-line characteristics are function of: Material electric and magnetic properties Dielectric Thickness (T D ) Width of conductor (W C ) Trade-off T D  ; C 0 , L 0 , Z 0  W C  ; C 0 , L 0 , Z 0  To a first order, t-line capacitance and inductance can be approximated using the parallel plate approximation. Base equation

13. Improved Microstrip Formula Parallel Plate Assumptions + Large ground plane with zero thickness effective To accurately predict microstrip impedance, you must calculate the effective dielectric constant. From Hall, Hall & McCall: Valid when: 0.1 < W C /T D < 2.0 and 1 < e r < 15

14. Improved Stripline Formulas Same assumptions as used for microstrip apply here From Hall, Hall & McCall: Symmetric (balanced) Stripline Case T D1 = T D2 Offset (unbalanced) Stripline Case T D1 > T D2 Valid when W C /(T D1 +T D2 ) < 0.35 and T C /(T D1 +T D2 ) < 0.25

15. Refection coefficient Signal on a transmission line can be analyzed by keeping track of and adding reflections and transmissions from the “bumps” (discontinuities) Refection coefficient Amount of signal reflected from the “bump” Frequency domain  =sign(S11)*|S11| If at load or source the reflection may be called gamma (  L or  s ) Time domain  is only defined a location The “bump” Time domain analysis is causal. Frequency domain is for all time. We use similar terms – be careful Reflection diagrams – more later

16. Reflection and Transmission   Incident Reflected Transmitted

17. Special Cases to Remember 1     Zo  0      1 0 0      Vs Zs Zo A: Terminated inZo Vs Zs Zo B: Short Circuit Vs Zs Zo C: Open Circuit

18. Transmission Lines, Reflections, and Termination Short Circuited Line

19. Transmission Lines, Reflections, and Termination Open Circuited Line

20. Transmission Lines, Reflections, and Termination If the source impedance (R src ) does not equal Z 0, then reflections occur at the near end of the line as well as at the far end. Each end of the line has its own value of ρ. The principle of superposition applies, so that voltage at any point on the line and instant in time is the sum of that point’s initial condition and all waves that have passed it so far. The end of a transmission line is said to be matched if it is terminated with its characteristic impedance.

21. Transmission Lines, Reflections, and Termination Mismatched Line

22. Transmission Lines, Reflections, and Termination Matched Line

23. Model http://www.fourier-series.com/rf- concepts/flash_programs/Reflection/inde x.html http://www.fourier-series.com/rf- concepts/flash_programs/Reflection/inde x.html