1. Propulsiometer Instrumented Wheelchair Wheel Prepared by: Seri Mustaza (BME) Siti Nor Wahida Fauzi (BME) Ahmad Shahir Ismail (EECE) Hafizul Anwar Raduan (CompE) Advisor: Dr. W Mark Richter (PhD, Director of Research and Development, MAXmobility)

2. MAXmobility Accessible wheelchair treadmill Basically, working with ergonomic wheelchair:  Propulsiometer instrumented wheelchair wheel  Transfer friendly wheelchair  Variable Compliance Hand-Rim Prototype (VCHP)  Effective ways to propel the wheel

3. Propulsiometer Located on tubular hoop that can be mounted on different sizes of wheelchair’s wheel. To access the load applied by manual wheelchair user. Consist of DAQ, load cell, wireless transmitter, battery, DC/DC converter, sensor. Mainly use as research tool in lab. Ex: Calculating metabolic rate

4. Propulsiometer

5. Viasat MiniDAT™ Battery Sensor Load Cell DC/DC Converter

6. Data collected from propulsiometer to the PC Force, Torque & Wheel Angle

7. Load Cell signals Each of the 6 signals ranges from -5 V to +5 V 12 bit A/D converter Resolution = range/# of states (10/4096) For each step size, would equals to 2.4412mV.

8. MiniDAT™  16-bit resolution  16 single ended or 8 differential analog inputs  8 digital I/O lines  IEEE 802.11 wireless LAN  Uses 15V DC voltage  7.9 x 4.2 x 1.42 inches (LWH)  Weight = 1.5lb  Cost = $4,625.00

9. Problem MiniDAT is no longer available Bulky Use too much power Cost = $4,625.00 Have to wait about 20 minutes to reboot

10. Main GOAL Replacing MiniDAT™

11. Specific Goals Size: 4 x 4 x 0.5 inches (LWH) Weight= ~0.25lb Cost= less than $1000.00 Low power consumption

12. Target Specification 7 analog channels and 1 digital channel A/D with 12 bit resolution 1 quadrature encoder input Wireless capability Sampling rate of at least 10 kHz Accepts voltage signal of -5/+5 volts Power consumption ~5 watts Small and compact

13. Circuit Diagram

14. Circuit Schematic

15. Components (Development Kit) BASIC Stamp® Discovery Kit  Basic Stamp 2 Module (microcontroller) Speed = 20MHz RAM = 32 Bytes Size = 1.2 x 0.6 x 0.4 inches (LWH)  Uses 9V to operate  Manual and software (PBasic)

16. Components (A/D converter) MAX1270  8 channel single-ended  12-bit resolution  Programmable input range ( 10V, 5V, 5V, 0V)  Sampling rate of 110ksps  Operates at 5V

17. Components (Quadrature Decoder Chip) LS7166  8-bit tri-state I/O bus  No external clock required  Operates at 5V

18. Components (Wireless Serial Adapter) Socket Cordless Serial Adapter (CSA)  Uses RS232 (Serial Port)  Has a class 2 Bluetooth  Range up to 10m  Simple plug, install, and play

19. Interfacing with the computer The BASIC Stamp module is connected to the computer wirelessly BASIC Stamp Windows Editor version 2.2.5 will be used to program the module Programming is performed in the PBASIC language

20. Programming: A/D Two main portions:  Retrieving the 6 readings from the load cell  Sending the data to a spreadsheet file Since MAX1270 has only one T/H circuit, each readings has to be retrieved separately Maximum of 18µs to retrieve all 6 readings

21. Programming: Quadrature Decoder Three main parts:  Initializing the chip  Reading position and direction  Sending data to a spreadsheet file The LS7166 chip has to be properly initialized Then the position and direction can be read and sent to a file

22. Example code (A/D): ReadSensorData s/r: ReadSensorData: controlbyte = basiccontrol ^ (channel << 4) bytea = 0 byteb = 0 shiftout outputpin, clockpin, msb, [controlbyte \ 8] … Main loop: top: for channel = 0 to 7 gosub ReadSensorData gosub SendSensorData next pause sleeptime goto top

23. Current Status Finalizing the circuit layout on the wheel Finishing the programming portion Testing the program