1. Potential Divider Circuits Sometimes elements on circuit need less than the total voltage potential. Circuit that can be adjusted to divide the p.d. (voltage) called potential divide. Which type of circuit divides voltage? Series circuits divide total input voltage between resistors.

2. A simple series circuit divides the voltage among resistors. Sketch the circuit below. Derivation of the potential divider equation. V out

3. To find partial voltage:V 2 = (V tot ) R 2 R 1 + R 2. Basic pd divide equation. Around R 2 I = V 2 /R 2 Sub in & rearrange V 2 = V tot R 2 (R 1 + R 2 ) I = V tot – R eq I = V tot (R 1 + R 2 )

4. The equation: V 2 = (V tot ) R 2 R 1 + R 2. Describes the output voltage of a particular resistor as a fraction of the total current based on the fraction of resistance offered by a particular resistor.

5. Ex 1: 2 resistors are in series to 10V. Use the equation to find V 1 & V 2.around R 1 & R 2. V 1 = 10 V x (3  ) = 2 V 15  3  12  10 V V 2 = V – V 1 = 10 – 2 – 8V. V 2 = (V tot ) R 2 R 1 + R 2.

6. Ex 2: Two resistors are connected to 8V as below. Find V 1 & V 2. 5 k  12 k  8 V V 1 = 2.4 V V 2 = 5.6 V V1V1 V2V2

7. Ex 3: Given 3, 5 k  resistors as below, find the V ab, V bc. Compose an equivalent circuit a b c 8V a b c 5 k  2.5 k  8V

8. Apply the equation V ab = 8 x (5 x 7.5) = 5.3 V. V bc = 8 - 5.3 = 2.7 V.

9. Proportionality Equation for series circuit. Since I = V 1 /R 1 = V 2 /R 2. V 1 /R 1 = V 2 /R 2. V 1 /V 2 = R 1 /R 2. R1R1 R2R2 I V1V1 V2V2

10. Ex 4: Use proportionality to find V 1. 2.5 V 4  8  V1V1 5 V

11. Ex 5: Choose an equation to solve for V on the 10  resistor. Using potential divide equation 50 V 7  10  100 V 3 

12. Potentiometers variable voltage

13. Kerr 145 potentiometer Demo, explanation, problem. Nov 04 pg 15 Kerr pg 150 #32.

14. Use your data booklets to sketch the circuit using the IB symbols.

15. It’s as if wire is many resistors in series. The voltmeter can read the pd around some of the resistance by touching specific points. V 6.0 V

16. Simplest potentiometer has slider contact. At top V = 2 V Halfway V = 1 V At bottom V = 0V. 2V This is equivalent. Why? 2V

17. Ex: If there are 30cm above & 70cm below the contact, what is the voltmeter reading? The reading around70cm. Partial R = 70 cm Total R = 100 cm V = 2V x (70/100) 1.4 V 2V 30cm 70cm

18. Ex: If there are 40cm above & 60cm below the contact, what is the voltmeter reading? The reading around 60cm. Partial R = 60 cm Total R = 100 cm V = 2V x (60/100) 1.2 V 2V 40cm 60cm

20. I can add another resistor to the circuit and determine the reading on the voltmeter.

21. The maximum resistance of this variable resistor is 100 . When the sliding contact, S, is at contact A, what will the voltmeter read? It will read 6V (the resistor is bypassed): the maximum reading of voltage in this circuit. What is the reading of the voltmeter when the sliding contact is moved to B?

22. We have, in effect, the following situation. Therefore, the voltmeter will read 3V. It is not possible to make the reading of the voltmeter vary from zero up to the full voltage of the supply using this circuit.

23. When all 3 connections of the 100  variable resistor are used as below, what will the voltmeter reading be? X is a wire, the contact is at B. Zero. The contact bypasses the bulb like a short circuit. The wire x is in parallel with the bulb.

24. The variable resistor is 100 . What resistance does it supply on this circuit? 50 , since resistance is directly proportional to length.

25. Uses of potentiometers To control volume. To control lights (dimmer switch).

26. Electrical Sensors Devices whose resistance changes with changing physical conditions.

27. Strain Gauge When stretched R increases b/c it gets longer & skinnier. Find symbol put in notes.

28. Light Sensor LDR – light dependent resistor Resistance decreases when light shines on it. See symbol.

29. Thermistor – resistance varies with temperature. Usually the R decreases w/increasing temperature (counter to our wires). Symbol.

30. Using Potential Divide with Sensors 12V LDR - When light stops shining, its resistance increases and V out increases. If it V out gets high enough, the switch will activate perhaps putting on lights. The p.d. divide is needed to create a p.d. to activate switch. switch

31. Use of Sensors Ex: The cell has an emf of 12-V and no internal resistance. The p.d. required to activate the switch is 5-V. Find the value of R 1 that will cause the switch to activate when the resistance of the LDR is 200 k . switch

32. Rearrange: V out = (V in ) R 2 R 1 + R 2. solve for R 1. R 1 = (R 2 ) V in - V out V out.

33. Solve for R 1. 280 k .

34. Which would be a good sensor to use with a fire alarm?

35. What would be a good use for a strain gauge?

36. Hwk. Read Hamper. 115 – 123 do pg 123 #21

37. Nov 04 pg 15