1. Page 1 Sapphire  Fab condition Room temp 23 ±2 ℃ ； △≦ ±1 ℃ /h Humidity have to below: 80%(spec 60 ±10 %)  Cooling system confirmed the first lay-out 12 tools assy main piping stainless ； sub-piping stainless PCW: Inlet 27 ±1 ℃ ;(outlet 33 ±1 ℃ ) ；△≦ ±1 ℃ /h ; △ T ＝～ 6 ℃ (max=40 ℃ ) PCW: Flow rate 10m3/h; pressure 3.5 bar Total 600RT  Power system confirmed the first lay-out 12 tools assy for local power cabinet 3 tools for one group; 400 ±10Vac Power cable tray is need Independent ground below 4Ω  Layout status stilling on going To split management and engineering office Labby and show room lay-out Fab entrance room lay-out 3 rooms for CEO/GM/VP  Facility FDMS facility design management system final confirming  Ar and ex-G and DI system Ar local supply; hot exhaust piping; close loop DI system

2. Page 2 Sapphire 1. 原則上以能控制恆溫恆濕且無持續微塵污染源即可。 2. 潔淨室溫度設計＜製程冷卻水。至少 1 ℃以上為避免冷凝水損害機台。 3. 溫度設計實例 : 濕度需低於 60±10% 。 4. 單一機台供電 :3P4W(400 ±10Vac)60Hz ； R_Gnd ≦ 4Ω 獨立接地 。 5. 規劃 12 台設置容量， 8/E 兩台， 9/E 三台，含二次側。 6. 單一機台用電 :280/280/20A; max=90kw; avg=75kw 。 ( 需三台一組已達相位平衡 ) 7. 每台機台約有 15kw 的能量散失 ( 變壓器 ) ，需要考量潔淨室空調或加裝 exhaust 排風。 8. 製程冷卻水單一流量 10 m3/h(167LPM) inlet:26~29 ℃ ( △≦ ±1/h; △ T=6 ℃ ) 9.Gas system: Ar purity: 99.99% ( 初期單機單鋼瓶供氣，後期為中央統一供氣 ) 。 10.exhaust system: 一般排。  潔淨室條件 vs 機台主要需求 Grower (outlet water ＜ 40 ℃ ) water flow/h inlet water outlet eater room temp 10m32127 20 ℃ 5m32133 20 ℃ 3.5m32139 20 ℃ 10m32632 25 ℃ 5m32638 25 ℃

3. Page 3 Sapphire by pass line  Design Concept of Cooling Water System Tank 2 10 tones Chiller 冰機 -20cm tilt - 5cm distance between growers -Valve close3.5bar -Valve open 2.5 bar -One production line have 12 tools Tank 1 20 tones EMO CT in Pump Need UPS 10m^3/hour Heat Exchanger Pump at least 50cm lower than pipe At least 4m higher than growers △ ≦ ±1 ℃ /h; △ T=6 ℃ -Pipes and Tanks must be made of stainless steel plastic that capable to withstand 4~6 bars and temperature up to 100 centigrade. -Cooling water have to higher than room temp 1 ℃ -ΔT≤+-1 ℃ /h -Add filter is need -Max temp below 40 ℃ S1 2.6bar 35 ℃ S2 2.6bar 30 ℃ S4 1.2bar 33 ℃ S3 1.3bar 28 ℃ by pass line Manual valve control pressure 4 bar To city Water exhaust 1.HH/LL sensor 2.Leak sensor 3.Over flow design Funnel 10 line 冰機冷卻水 製程冷卻水 1.HH/LL sensor 2.Leak sensor 3.Over flow design Funnel 10 line CT refill DI refill EMO CT out by pass line 冷卻水塔

4. Page 4 Sapphire 1.15s mean to next 15s mean vibration ≦ 1 mv 2.Max vibration in 15s ＜ 4 mv 3.Gnd ＜ 4 Ω 4.8~10 V must stable and control limit ＜ 1mv 5.Water out have to less then 40 ℃ else water vapper 6.12 set Grower power : 12*90=1080 kw 7.Chiller = Take out thermal energy = 1080*1.25=1350 kw 8.A group for 3 tools 9.3P4W400~420Vac(min376V)  Design Concept of Power System Heater thyristor 380V AC Spec: 410~390V 380V AC Spec: 0~380V 376V AC Spec: 0~376V 12V AC Spec: 0~12V 10V AC Spec: 0~10V Grower controller 750kva 400 ±10Vac Grower 1 Grower 2 Grower 3 R_Gnd ≦ 4Ω; 機台需獨立接地

5. Page 5 Sapphire

6. Page 6 Sapphire

7. Page 7 Sapphire

8. Page 8 Sapphire