1. Seventh Edition By David A. Madsen, Terence M. Shumaker, and David P. Madsen Civil Drafting Technology Chapter 13 Civil Engineering Detail Drawings

2. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 2 Figure 13 – 1: A vicinity map places a project site within an area of several square miles and provides a good overview of the site relative to the surrounding area. (Courtesy Lee-Pace Engineering, Inc.)

3. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 3 Figure 13 – 2: A subdivision composite utility site plan shows the utilities layout of the project on the land. (Courtesy Lee-Pace Engineering, Inc.)

4. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 4 Figure 13 – 3: This site plan shows the proposed layout of water and sanitary sewer systems. (Courtesy Lee-Pace Engineering, Inc.)

5. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 5 Figure 13 – 4: A section symbol shown on a plan view. This is section A, shown on sheet 6, and the view is to the right. (Courtesy Lee-Pace Engineering, Inc.)

6. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 6 Figure 13 – 5: This is section A, and it was cut on sheet 6 and is also shown on sheet 6. It is not to scale (N.T.S.). (Courtesy Lee-Pace Engineering, Inc.)

7. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 7 Figure 13 – 6: A typical cross section common to any location along the street of a subdivision project. (Courtesy Lee-Pace Engineering, Inc.)

8. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 8 Figure 13 – 7: A profile is a section that is cut along the length of a linear feature, such as this sewer line, and normally has different horizontal and vertical scales. (Courtesy Lee-Pace Engineering, Inc.)

9. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 9 Figure 13 – 8: This detail illustrates how the new water lines are to be deflected around the proposed sewer line. (Courtesy Lee-Pace Engineering, Inc.)

10. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 10 Figure 13 – 9: This detail drawing provides minimum standards for a cul-de-sac layout. (Courtesy Lee- Pace Engineering, Inc.)

11. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 11 Figure 13 – 10: Sidewalks, planter strips, and street width are shown in this cross section. (Courtesy Lee-Pace Engineering, Inc.)

12. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 12 Figure 13 – 11: Detail of sidewalk curb cut for handicap access. (Courtesy Lee-Pace Engineering, Inc.)

13. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 13 Figure 13 – 12: Street speed hump plan, sections, and detail. (Courtesy Lee-Pace Engineering, Inc.)

14. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 14 Figure 13 – 13: This detail provides plan and sections of sidewalk ramps and planter strip. (Courtesy Lee-Pace Engineering, Inc.)

15. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 15 Figure 13 – 14: Plan, section, and isometric view of a storm sewer drain. (Courtesy Lee-Pace Engineering, Inc.)

16. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 16 Figure 13 – 15: This plan and section details a 72 ” manhole. (Courtesy Lee-Pace Engineering, Inc.)

17. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 17 Figure 13 – 16: Plan and two sections of catch basin details. (Courtesy Lee-Pace Engineering, Inc.)

18. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 18 Figure 13 – 17: Manhole with storm sewer connections. (Courtesy Lee-Pace Engineering, Inc.)

19. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 19 Figure 13 – 18: Plan and section of sanitary sewer cleanout. (Courtesy Lee-Pace Engineering, Inc.)

20. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 20 Figure 13 – 19: Elevation detail of sanitary sewer cleanout with lateral connection to main sewer. (Courtesy Lee-Pace Engineering, Inc.)

21. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 21 Figure 13 – 20: Detail of metal catch basin for sanitary sewer line. (Courtesy Lee-Pace Engineering, Inc.)

22. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 22 Figure 13 – 21: This table provides the bearing areas for concrete thrust blocks at fittings. Thrust blocks provide structural support and integrity for pressurized water lines. (Courtesy Lee-Pace Engineering, Inc.)

23. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 23 Figure 13 – 22: Standard fire hydrant and valve box detail. (Courtesy Lee-Pace Engineering, Inc.)

24. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 24 Figure 13 – 23: Water meter installation detail. (Courtesy Lee-Pace Engineering, Inc.)

25. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 25 Figure 13 – 24: Valve box detail for a fire hydrant. (Courtesy Lee-Pace Engineering, Inc.)

26. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 26 Figure 13 – 25: Detail of floor-mounted pipe support. (Courtesy Lee-Pace Engineering, Inc.)

27. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 27 Figure 13 – 26: Detail of valve and blow-off line for water line. (Courtesy Lee-Pace Engineering, Inc.)

28. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 28 Figure 13 – 27: Air release valve detail for water main. (Courtesy Lee-Pace Engineering, Inc.)

29. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 29 Figure 13 – 28: Concrete masonry unit detail at footing and slab connections. (Courtesy Lee-Pace Engineering, Inc.)

30. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 30 Figure 13 – 29: Concrete masonry unit detail at wall and roof connections. (Courtesy Lee-Pace Engineering, Inc.)

31. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 31 Figure 13 – 30: Concrete masonry units and reinforcing bar detail at footing. (Courtesy Lee-Pace Engineering, Inc.)

32. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 32 Figure 13 – 31: Detail of structural steel column base plate connection to concrete. (Courtesy Lee-Pace Engineering, Inc.)

33. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 33 Figure 13 – 32: Steel reinforcing bar detail at wall-to-floor slab connection. (Courtesy Lee-Pace Engineering, Inc.)

34. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 34 Figure 13 – 33: Welded and bolted connection of steel beam to column. (Courtesy Lee-Pace Engineering, Inc.)

35. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 35 Figure 13 – 34: Structural steel column connections at column and roof canopy. (Courtesy Lee-Pace Engineering, Inc.)

36. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 36 Figure 13 – 35: Wood post, beam, and porch connection at concrete pier. (Courtesy Lee-Pace Engineering, Inc.)

37. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 37 Figure 13 – 36: Overhead door header details, with connection to concrete footing. (Courtesy Lee-Pace Engineering, Inc.)

38. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 38 Figure 13 – 37: Laminated beam connection and beam connection to steel column. (Courtesy Lee- Pace Engineering, Inc.)

39. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 39 Figure 13 – 38: Tabular dimension for typical header framing around an opening. (Courtesy Lee-Pace Engineering, Inc.)

40. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 40 Figure 13 – 39: Section details of materials and installation in a typical sidewall for a residence. (Courtesy Lee-Pace Engineering, Inc.)

41. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 41 Figure 13 – 40: Aluminum framing installation details for a fixed window. (Courtesy Lee-Pace Engineering, Inc.)

42. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 42 Figure 13 – 41: Section and fabrication details for a steel stair installation. (Courtesy Lee-Pace Engineering, Inc.)

43. Civil Drafting Technology, Seventh Edition David A. Madsen, Terence M. Shumaker, David P. Madsen © 2010 Pearson Higher Education, Upper Saddle River, NJ 07458. All Rights Reserved. 43 Figure 13 – 42: A legend is usually an arrangement of symbols located on one side of a drawing. This legend shows existing and new utility symbols.