1. bintec WLAN Controller Overview

2.  Designed for the requirements of organization with up to 100 employees  Suitable for installation from 2 to 24 Access Points  The installation of a new Wireless network must be possible without special training of the administrator.  The Wireless network must be support seamless hand-over for VoWifi phones. The network must be “Voice Ready”. bintec WLAN Controller Target definition

3.  The WLAN Controller requires no dedicated hardware or a server.  For up to 6 APs the WLAN Controller license is running a Master-AP  For 7-24 APs a bintec R1202 router is required a controller hardware.  The WLAN Controller infrastructure requires a DHCP server. The functionality of the DHCP server can provide by the WLAN Controller or via an external DHCP server (i.e. Microsoft Server 2008) bintec WLAN Controller The hardware

4. bintec WLAN Controller Installations with up to 6 APs Switch DHCP Server AP 2AP 3AP 6 WLAN Controller license at a W1002n (AP1) AP 1

5. bintec WLAN Controller Installations with up to 6 APs Switch R1202 WLAN Controller + DHCP Server AP 2AP 3AP 24 WLAN Controller license for up 24 APs at a R1202 AP 1AP 23

6.  Support the Access Points W1002n, WIx40n, WIx65n with SW-Release 7.9.6 or higher  Simple wizard based quick installation allow the installation in only five steps.  Automatic detection and installation of new access points.  Frequency management with automatic channel management  VLAN and Multi-SSID support  Any configuration changing, i. e. the adding of a new SSID, and the setup of the new configuration to all access points requires only a few clicks and is in a few seconds done.  Configuration management, the configuration are stored central at the WLAN controller. In case of power lost the WLAN controller distribute the configuration automatically after the power up.  The monitor support the detection of Neighbor AP und the supervision of clients.  Automatic firmware rollout for all managed access points. bintec WLAN Controller Functionality

7. bintec WLAN Controller WLAN setup in five steps: Step 1 Selection of the interface and definition of the DHCP Servers

8. bintec WLAN Controller WLAN setup in five steps: Step 2 Selection of the frequency band (2,4 or 5 GHz)

9. bintec WLAN Controller WLAN setup in five steps: Step 3 Definition of the SSID details …

10. bintec WLAN Controller WLAN setup in five steps: Step 4 The detected APs are shown. The APs there we want to manage are selected, …. and the installation is started by pressing the START button.

11. bintec WLAN Controller WLAN setup in five steps: Step 5 Finished ! The APs have now a channel definition and the units are managed.

12.  Functionality of the license  The WLAN Controller functionality is available at each R-Serie, W-Serie and WI-Serie with software release 7.9.6 or higher and requires a license.  Up to 6 APs are manageable from one of the Access Points (Master-AP). No dedicated hardware for the controller is required. The Master-AP required the WLAN controller licenses.  If the network contain more than 6 APs, a bintec router i.e. R1202 is required as WLAN controller.  The Slave APs requires no license, but a software release 7.9.6 or higher.  Without WLAN controller license only one AP is manageable. This enables the customer to testing the WLAN controller free of charge.  License  To keep the numbers of different part numbers small only a license for 6 Access Points is available  For the W-Series and the WI-Series only one license are possible to install to support up to 6 Access Points  For the R-Series only up to 4 license are possible to install to support up to 24 Access Points bintec WLAN Controller License model

13. Thank you for your attention