1. PHY 201 (Blum)1 MEMORY Digital Principles, Roger Tokheim Chapter 9

2. PHY 201 (Blum)2 Combinatorial Logic vs. Sequential Logic A circuit is said to be “combinatorial” if its output is determined solely by its inputs. Such a circuit can be realized in terms of logical gates (ANDs, ORs and NOTs). A circuit is said to be “sequential” if its output is in part determined by its history. History dependence here means bits (high or low states) that were previously stored by the circuit. If the sole purpose of the circuit is to store values, it is called memory.

3. PHY 201 (Blum)3 Flip-flops and Registers A circuit that can store a single bit is known as a flip-flop. A group of flip-flops working in parallel as a unit to hold a “word” is known as a register. A group of addressable registers (done with a decoder) is known as memory.

4. PHY 201 (Blum)4 Memory Address Register The Memory Address Register is for holding the address of the memory that is currently being processed. It is the input to the decoder. The decoder in turn connects to a series of registers. At this lowest level, addresses are absolute but at a higher level addresses may be relative or absolute.

5. PHY 201 (Blum)5 Like an Array AddressValue 0000AB 000134 000273 000384 0004CC ……

6. PHY 201 (Blum)6 Reading and Writing The action of placing a value in a memory circuit (a.k.a. a cell) is called writing. Putting a high value into a cell is referred to as “setting.” Putting a low value into a cell is referred to as “resetting.” Accessing the value in a memory cell without affecting it is called reading. Grammatically, the CPU is the subject; the memory is the object The CPU writes to memory. The CPU reads from memory.

7. PHY 201 (Blum)7 The Clock The timing of these actions, especially the “write” are controlled by the clock. One can think of a computer’s clock as something that steadily oscillates betweens the values 0 and 1 Units of memory (flip flops) will can have three types of input: Control: whether or not to write Timing: when to write Data: what to write Sometimes control and timing are combined.

8. PHY 201 (Blum)8 ROM Read Only Memory As the name suggests the user only reads this type of memory; the writing is typically done by the manufacturer. ROM is nonvolatile, that is, a supply of energy is not required to keep the data intact. That is, ROM is not lost when the computer is turned off.

9. PHY 201 (Blum)9 Using ROM Most personal computers contain a small amount of ROM that stores critical programs such as the program that boots the computer. In addition, ROMs are used extensively in calculators and peripheral devices such as laser printers, whose fonts are often stored in ROMs.

10. PHY 201 (Blum)10 Types of ROM ROM: data is written by manufacturer PROM: programmable read-only memory, data is written by user PROMs are manufactured as blank chips on which data can be written with a special device called a PROM programmer (a.k.a. burner) Like burning a CD

11. PHY 201 (Blum)11 Types of PROM PROM usually implies “write once” EPROM erasable programmable read only memory data can be erased and rewritten Some use ultraviolet (UV) light, requires removing it from the computer EEPROM, electrically erasable programmable read-only memory, is erased by electronic means Does not have to be removed from computer

12. PHY 201 (Blum)12 Uses Of ROM Microcode portion of CPU The lowest-level instructions that directly control a microprocessor. A “plus” instruction will be stored in a program in RAM; the code that tells the hardware what to do when it encounters a plus is in ROM Basic Input/Output System (BIOS) Code burned into motherboard’s ROM; it handles interfacing between the operating system and peripherals (IO).

13. PHY 201 (Blum)13 RAM RAM Random Access Memory Data can be accessed (read) Sequentially: you start at the beginning and go through the sequence of locations Like a cassette or video tape Randomly: you can jump to any location without proceeding through all previous locations Like a CD or DVD (no need for fast-forwarding, rewinding, etc.) ROM is also random access, but the term RAM refers to volatile memory, memory requiring an energy source.

14. PHY 201 (Blum)14 Types of RAM SRAM: Static RAM The objective of memory is to hold a value, so being static is good. The value is held without the need for “refreshing.” Fast but expensive. DRAM: Dynamic RAM The value must be “refreshed” or it will become lost or corrupted. Slow but cheap.

15. PHY 201 (Blum)15 Types of DRAM Synchronous DRAM (SDRAM) actually synchronizes itself with the CPU's bus Deals with data in “bursts” so it doesn’t have to go through the addressing process of successive data locations DDR SDRAM – Double Data Rate SDRAM Double data refers to the number of times that data can be sent along the bus connecting processor and memory Also DDR2 and DDR3

16. PHY 201 (Blum)16 Blurring the distinction between RAM and ROM NVRAM: Non-Volatile Random Access Memory, is RAM that does not lose its data when the power goes off. A separate power source such as a battery allows the RAM to hold onto its information until it can be written to more permanent form: to EEPROM or to storage (disk) Some modems use it to keep phone numbers and/or modem profiles.

17. PHY 201 (Blum)17 Blurring the Distinction II Flash memory: A version of EEPROM that can be erased and reprogrammed in blocks rather than one byte at a time. This makes writing (burning) easier/faster. Many PCs use flash memory for their BIOS – a flash BIOS. Flash memory is often used in modems, as it allows the manufacturer to support new protocols as they become standardized.

18. PHY 201 (Blum)18 Cache A generic term used to describe guessing what data will be used next and placing it where it can be accessed more quickly A cache hit is a correct guess A cache miss is an incorrect guess Memory Cache uses SRAM which is faster than DRAM L1: SRAM that is right on the microprocessor chip L2: (originally) not on the chip

19. PHY 201 (Blum)19 Cache When writing to cache, there are different scenarios Write back: updates cache first and memory later (faster) Write through: updates cache and memory together (slower but maintains consistency)

20. PHY 201 (Blum)20 SRAM Pros Speed SRAM is faster than DRAM, because DRAM requires refreshing which takes time Simplicity SRAM is simpler to use than DRAM, again because DRAM requires refreshing

21. PHY 201 (Blum)21 SRAM Cons Size SRAM is a more complicated circuit, it involves more transistors than DRAM, and hence it is larger Cost Again SRAM is more transistors and so it costs more Power Since SRAM involves a constant current, it uses more power than DRAM Heat Again since SRAM involves a constant current, it produces more heat

22. PHY 201 (Blum)22 Error Detection Parity Odd parity: add an extra bit to a word and insist that the total number of 1’s be odd Even parity, ditto but number of 1’s even Example of odd parity 000000001 000000010 000000100 000000111

23. PHY 201 (Blum)23 Vertical parity 000000001 010100010 000001101 010100111 001001001 000001011 000001101 000011010 110100011

24. PHY 201 (Blum)24 Error Detection and Error Correction Code If a parity check reveals a parity error, one can request data be resent Parity CRC (cyclic redundancy check) checksum Error Correction Code: in addition to detecting a mistake can help fix it Hamming code

25. PHY 201 (Blum)25 Virtual memory What if there’s not enough memory for a program? The operating system has a book-keeping scheme called virtual memory. It assigns the program virtual addresses. At any given time, only a part of the program is really in memory. The operating system keeps track of the correspondence between virtual addresses and real addresses (in storage, i.e. the disk).

26. PHY 201 (Blum)26 Virtual memory (cont.) As program runs, different parts of the program need to be in the real memory. The operating systems breaks the code into pieces called pages. Putting the new part of the code into real memory is called swapping or paging. Swapping is slow; it’s why adding memory might improve speed

27. PHY 201 (Blum)27 Shadowing Putting parts of the ROM BIOS which can be slow into RAM which can improve speed. In some sense this is another version of caching.

28. PHY 201 (Blum)28 Memory Packaging SIPP: single inline chip packages (OLD) Little circuit board with memory chip Has pins, hard to install SIMM single inline memory module (OLD) Like SIPP but no pins, easier to install a 32-bit path to the memory DIMM dual in-line memory module, a 64-bit path