1. 09/13/20111 Status of high intensity polarized electron gun project at MIT-Bates Evgeni Tsentalovich MIT

2. 2 eRHIC (Linac-ring version) Requires a polarized electron source with an extremely high current ( at least 50 mA). Average current of tens or even hundreds of mA is required Modern state-of-the-art guns produce ~100-200  A Average current of ~ 1 mA achieved in tests at JLab and Mainz; lifetime ~ 20 h Average current of up to 10 mA achieved at Mainz with very short lifetime (needs active cathode cooling) Main problem – ion backbombardment

3. 05/20/20083 Ion damage mostly the center of cathode (Bates results) Laser beam profile Damage pattern

4. High Intensity Polarized Electron Gun The principal points to achieve high average current: Large area cathode. Ions tend to damage the central area of the cathode – ring-shaped emission pattern. Active cathode cooling. Very small beam losses could be allowed near the gun ( ).

5. Phase I results: beam simulations. Three different initial emitting pattern were used: Ring-shapedGaussianFlat The pictures represent the beam shape 400 mm from the cathode.

6. Beam line. Pipe aperture ~±34 mm. Gun Dipoles Solenoidal lenses Beam dump

7. Losses estimates It is difficult to get a correct shape of the tails in regular simulations. Special simulations with electrons emitted only from the edge of the cathode (r>11.8 mm) have been performed. The resulting tail can be approximated by Gaussian distribution: R, mm 10 11 12 13 14 15 1617 Losses.037.012 Results for the ring-shaped beam at the entrance into the first dipole. r0=4.9 mm, σ=1.9 mm. Aperture is about 30 mm. Similar calculations have been performed in several different locations in the beam line with all three initial emitting pattern. No substantial beam losses have been discovered.

8. Ion distribution Electron current profile Ion energy profile Ion current profile Simplification: the cross section ionization was independent of electron energy.

9. Interesting problem - beam dump PUMPS Current monitor Water cooling Beam I~50 mA → P~6 kW !!! Outgasing in the dump could be serious problem.

10. Biased beam dump (energy recovery) -120 kVGun power supply -119 kV Gun Beam line Beam dump Electron energy in the dump drops from 120 kV to 1 kV. Heating power in the dump drops from 10 kW to 100 W 100 W in the dump still needs to be removed, and now dump is at 120 kV ! Needs fluorinert chiller. Isolated 1 kV power supply

11. 11 Cathode Cooling Test Chamber Coolant in Coolant out HV Laser Manipulator Cathode Crystal

12. Cathode – anode assembly Fluorinert (cooling agent)

13. Cathode – anode assembly Fluorinert (cooling agent)

14. Cathode – anode assembly

15. Pack with a crystal

16. Heat exchanger

17. Preparation chamber

18. General assembly – top view GUN PREP. CHAMBER LOAD LOCK SECOND DIPOLE LENSES MANIPULATORS

19. General assembly – top view GUN PREP. CHAMBER LOAD LOCK FIRST DIPOLE

20. Tests results in the cathode cooling chamber -Vacuum manipulations works very well: excellent illumination with internal halogen bulbs, good visibility, reliable pack transfer. -High Voltage: processed the chamber to 125 kV, but electrical discharges happened. The ceramic pipes need better protection from the electrons produced by cold emission. -Temperature control: the pack temperature could be held at below 25 °C even at the maximum laser power available (about 34 W on the crystal)

21. Vacuum features of the gun chamber 100 l/s Ion pump with 400 l/s NEG. 4 additional 400 l/s NEGs (only two are currently installed). The chamber walls are thin (~ 3 mm) to reduce outgasing. The chamber and most of the parts have been prebaked to 400°C before the final assembly. Bake-out at 250°C after the final assembly. RGA readings after bake-out: m216182844 P, mbar

22. HV processing The operating voltage is 120 kV The gun was processed to 150 kV After the processing no activity (measurable dark current, vacuum increase) could be detected at 120 kV The Fluorinert produces virtually zero conductivity (unable to measure).

23. Current status The gun chamber: built and tested. It was vented 3 weeks ago to install the first dipole followed the gate valve and 2 additional NEGs. Rebaked and HV reprocessed. The preparation chamber: design is completed, the main chamber has been manufactured, many parts are already ordered. Load lock – the design is in progress. Beam line – conceptual design is completed, some parts are designed, the dipole vacuum chambers have been manufactured.