Download presentation
Presentation is loading. Please wait.
Published byEmery Pope Modified over 9 years ago
1
1 DAQ for FVTX detector Implementation Mark Prokop Los Alamos National Laboratory
2
Mark Prokop, FVTX Review Nov 20082 Talk Outline Overall Readout System ROC Pre-Production Prototype FEM Pre-Production Prototype Risk Factors Summary
3
Mark Prokop, FVTX Review Nov 2008 Technical Challenges for Readout Challenges –Radiation environment around the detector 10 year Total Integrated Dose - <200 kRad Acute Radiation Effects on FPGA configuration SRAM memory –Data Bandwidth 3.38 Terabits/sec –Number of Data I/O Lines ~17k LVDS Pairs Solutions –Use Radiation Tolerant FPGAs close to the detector ACTEL FLASH based FPGA –IR Data Compression Circuitry Sync word removal –FO Data Transport to FEM 16 - 2.5 Gigabit/sec FO data links 3
4
Mark Prokop, FVTX Review Nov 2008 Overall Readout Strategy ½ of each detector arm is read out independently 6 ROC cards collect and compress the data from the detector Each ROC card sends fiber output to two FEM boards in the Counting House Slow Control fiber sends control data stream up/down the FEM↔ROC Slow Controls link Clock Distribution Board distributes Beam Clock and Start signals to individual ROC boards (the signals are sent over dedicated optical fibers)
5
Mark Prokop, FVTX Review Nov 2008 DAQ ROC board layout started Clock Distribution Board layout started Components, cost, power consumption estimated Electronics supply voltages regulated on ROC Voltages Required: –3.3V: FO Tx/Rx –2.5V: SERDES, ROC I/O, Wedge –1.5V: FPGA Core Total power per ROC board ~ 20 W board + 18 W for V regulators = 38 W Total Power per ½ Arm = 228 W Total Power per Arm = 456 W Total Power for Detector = 912 W 5 12 ROC boards + 2 Clock Distribution boards in a “big wheel”
6
Mark Prokop, FVTX Review Nov 2008 ROC Board - WBS 1.5.2 6 Slow Controls FPGA Gas Seal Area FPGA A FPGA B FPGA C FPGA D 8x FO Tx Slow Controls FO Tx/Rx SERDES Wedge Connectors Power JTAG FPGA SC SERDES 10.2”(W) x 11.75”(L) 30°
7
Mark Prokop, FVTX Review Nov 2008 FEM Board – WBS 1.5.3 7 8x FO Rx Slow Controls FO Tx/Rx Slow Controls FPGA Main FEM FPGA SERDES EEPROM Rotary Switch Power Bus Interface Slow Controls SERDES DCM II SERDES DCM II FO Tx VME 6U Board
8
Mark Prokop, FVTX Review Nov 2008 Risk Factors FVTX DAQ design utilizes well tested, commercially available parts, nothing “state-of-the-art”. Risk – low Design of the ROC requires a significant amount of digital signal tracing and excellent ECAD skills. Risk – moderate FEM board is simple VME board with a few components. Moderate number of I/Os. Risk – low None of the WBS 1.5 items is on the critical path 8
9
Mark Prokop, FVTX Review Nov 20089 Summary WBS 1.5 – Technical Specification DocumentTDR, DAQ overview document Prototype statusROC and FEM pre-production prototypes – started Electronics ComponentsAll available from distributor stock Production Quantities24 + 4(spares) ROC boards 48 + 6(spares) FEM boards Heat load38 W per ROC board 456 W per arm On-project Manpower1 EE + 1 ECAD Institutions InvolvedLANL Infrastructure Defineddraft QA procedures in placeFull QA plans for ROC and FEM
10
Mark Prokop, FVTX Review Nov 2008 DAQ Implementation Backup Slides
11
Mark Prokop, FVTX Review Nov 200811 Summary WBS 1.5 - Schedule PHENIX System Test:1/09-3/09 ROC Pre-prod Proto:10/08-1/09 FEM Pre-Prod Proto:3/09-7/09 ROC Production:10/09-1/10 FEM Production:10/09-1/10
12
Mark Prokop, FVTX Review Nov 2008 Summary WBS 1.5 - Cost ROC Pre-production:$74k FEM Pre-production:$85k ROC Production:$390k FEM Production:$350k Ancillary:$116k Fibers and Lab Equipment:$124k 12
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.