1. Spatial Referencing GIS in the Sciences ERTH 4750 (38031) Xiaogang (Marshall) Ma School of Science Rensselaer Polytechnic Institute Tuesday, February 05, 2013

2. Review of last week’s work In the lecture –Geographic phenomena: fields and objects –Computer representations: raster and vector –Autocorrelation and topology In the lab: MapInfro Professional –Map objects: text, points, lines and polygons –Objects  layers, tables  maps –Analyzing data: queries & thematic Maps Questions?

3. Acknowledgements This lecture is partly based on: –Huisman, O., de By, R.A. (eds.), 2009. Principles of Geographic Information Systems. ITC Press, Enschede, The Netherlands

4. Outline 1.Spatial referencing basics 2.Map projections

5. 1 Introduction Spatial referencing encompasses the definitions, the physical/geometric constructs and the tools required to describe the geometry and motion of objects near and on the Earth’s surface –Some of these constructs and tools are usually itemized in the legend of a published map

6. 1 Introduction Legend of a German topographic map

7. 2 Spatial referencing basics (a)International Terrestrial Reference System – the origin is in the center of the mass of the Earth. This system rotates together with the Earth. Used in extra-terrestrial positioning systems, like GPS (b)International Terrestrial Reference Frame – a set of points with high precision location and speed definition (a triangle-based network). The speed expresses the change of location in time due to geophysical (e.g. tectonic) phenomena

8. 2.1 Basic coordinate systems Geographic coordinates – Two- dimensional coordinate system, referring to locations on (or close to) the surface of the Earth, using angles for defining locations Cartesian coordinates – Rectangular coordinate system, using linear distance for defining locations on a plane

9. 2.2 Shape of the Earth Development of the ideas about the shape of the Earth: –An oyster (The Babylonians before 3000 BC) –A circular disk (early antiquity; approximately 5-300 B.C., but this concept survived till the 19thcentury) –A very round pear (Christopher Columbus in the last years of his life) –A perfect ball  a sphere(Pythagoras in 6thcentury BC) –An ellipsoid, flattened at the poles (Newton around the turn of the 17 th and 18 th centuries) –…but what is it exactly? Modeling the shape of the Earth is needed for spatial referencing. In this sense, topographic differences (e.g., mountains and lowlands) are not taken into account.

10. 2.2 Shape of the Earth The geoid –The surface of the Earth is irregular and continuously changing in shape due to irregularities in mass distribution inside the earth. –Geoid: An equipotential surface in the gravity field of our planet; a ‘potato’ like shape, which is ever changing, although relatively slowly. –Every point on the geoid has the same zero height all over the world.

11. 2.3 Datums For spatial referencing we need a datum: a surface that represents the shape of the earth. Due to practical reasons, two types of spatial positioning are considered: –Computing elevations (related to a vertical datum), –Computing horizontal positions (related to a horizontal datum). Source of clip art: http://www.school-clip-art.com

12. 2.3.1 Vertical datum A reference surface for heights (vertical datum) must be: –a surface of zero height, –measurable (to be sensed with instruments), –level (i.e. horizontal). The geoid is practically the most obvious choice: –the geoid is approximately expressed by the surface of all the oceans of the Earth (mean sea level), –every point on the geoid has the same zero height all over the world.

13. Mean sea level = geoid? Mean Sea Level (MSL) is used as zero altitude –the ocean’s water level is registered at coastal locations over several years Sea level at the measurement location is affected by tidal differences, ocean currents, winds, water temperature and salinity Many of these local vertical datums exist –Different countries, different vertical datums. –E.g.: MSLBelgium-2.34 m = MSLNetherlands Tide table of Isle aux Morts (Canada). Sea surface changes predictably but irregularly. Source: http://www.lau.chs-shc.dfo- mpo.gc.ca/cgi-bin/tide-shc.cgi

14. Vertical datum in the United States The North American Vertical Datum of 1988 (NAVD88) Elevation marker at The Colorado State Capitol Source: http://www.mesalek.com/colo/trivia/elev.html Its inscription reads "State of Colorado / 2003 Mile High Marker / 5280 Feet Above Sea Level / NAVD 88".

15. Highest and lowest points in the US Lowest point: Death Valley, Inyo County, California −282 ft (−86 m) below sea level Highest point: Mount McKinley, Denali Borough, Alaska +20,320 ft (6,194 m) above sea level Source: http://en.wikipedia.org/wiki/Geography_of_the_United_States

16. Elevation measurement from the vertical datum Starting from MSL points, the heights of points on the Earth can be measured using geodetic leveling techniques

17. Geoid versus ellipsoid The geoid surface continuously changes in shape due to changes in mass density inside the earth (i.e. it is a dynamic surface). Due to its dynamics and irregularities, geoid is NOT SUITABLE for defining time- indifferent elevations (as well as it is not a suitable reference surface for the determination of locations, see later). A (regular) mathematical vertical datum is needed. The best approximation of the geoid is an ellipsoid. Note that if a=b then it is a sphere. Rotation of this ellipse around the minor axis gives the ellipsoid

18. Comparison of vertical datums Elevations measured from different datums are different, thus, the datum has to be known for proper georeferencing.

19. 2.3.2 Horizontal datum For local measurements, where the size of the area of interest does not exceed 10 km, a plain is a proper horizontal datum for most of the applications. For applications related to larger areas the curvature of the Earth has to be considered. Mathematically describable surface: ellipsoid (sphere). Note that the ellipsoid is not a plain. A map projection has to be applied (see later in this lesson) to represent the points on the ellipsoid in the plain of the map. ppt

20. Local horizontal datums Countries establish a horizontal datum –an ellipsoid with a fixed position, so that the ellipsoid best fits the surface of the area of interest (the country) –topographic maps are produced relative to this horizontal (geodetic) datum Horizontal datum is defined by the size, shape and position of the selected ellipsoid: –dimensions (a, b) of the ellipsoid –the reference coordinates (φ, λ and h) of the fundamental point –angle from this to fundamental point to another point

21. Hundreds of local horizontal datums do exist Most widely used datum-ellipsoid pairs Courtesy: https://www.navigator.navy.mil

22. Local and global datums Local and global ellipsoids related to the geoid. The shapes are exaggerated for visual clarity.

23. Local and global datums Attempts to come to one single global horizontal AND vertical datum: –Geodetic Reference System 1980 ellipsoid (GRS80) –accurate global geoid in near future? Among difficulties: –accurate determination of one ‘global’height –from hundreds of local datums to one global datum If successful: –GIS users don’t have to bother about spatial referencing and datum transformation any more

24. Commonly used ellipsoids These selected ellipsoids are listed here as an example. There is no contradiction between this list and the figure in slide 18, since in all the regions several ellipsoids are used.

25. Horizontal datums - example Datum: ellipsoid with its location. Note that the above ellipsoids are the same, but their positions are different.

26. 2.3.3 Datum transformations Why ? –For the transformation of map coordinates from one map datum to another What ? –Transformation between two Cartesian spatial reference frames How ? –Transformation parameters (shift and modify ellipsoid) Rotation angles (α, β, γ) Translation (origin shift) factors (X 0, Y 0, Z 0 ) Scaling factor (s)

27. 3 Map projections The curved surface of the Earth (as modeled by an ellipsoid) is mapped on to a flat plane using a map projection. Two reference surfaces are applied: –Ellipsoid for large-scale mapping (e.g. 1:50,000) –Spherefor small-scale mapping (e.g. 1:5,000,000) See also: http://www.bbc.co.uk/history/british/empire_seapower/launch_ani_mapmaking.shtml

28. 3.1 Classes of map projections Surfaces used for projecting the points from the horizontal reference surface (datum) onto are: –plane or –a surface that can be deduced to a plane: cone cylinder Any other (closed) body that consists of planes can be also used (e.g. a cube), but those are mostly of limited practical value.

29. Secant projections In tangent projections the projection surfaces touch the reference surface in one point or along a closed line. In secant projections the projection surface intersect the reference surface in one or two closed lines.

30. A transverse and an oblique projection Normal projection: α=0º Transverse projection: α=90º Oblique projection: 0º<α<90º –Where α is the angle between the symmetry axis of the projection surface and the rotation axis of the Earth

31. Azimuthal projection example Stereographic projection is used frequently for mapping regions with a diameter of a few hundred km. Distortions strongly increase towards the edges at larger areas. Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

32. Cylindrical projection example In this projection, Y coordinates are defined mathematically Conformal projection Mercator projection was used for navigation Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

33. Conic projection example Parallels are conentric unequally spaced circles Conformal projection Used for areas alongated in W-E direction Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

34. 3.2 Properties of projections The following major aspects are used for grouping the projections: –Conformality Shapes/angles are correctly represented (locally) –Equivalence ( or equal-area ) Areas are correctly represented –Equidistance Distances from 1 or 2 points or along certain lines are correctly represented The compromise projections do not have the above properties, but the distortions are optimized.

35. Conformal projection Shapes and angles are correctly presented (locally). This example is a cylindrical projection. Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

36. Equivalent map projection Areas are correctly represented. This example is a cylindrical projection. Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

37. Equidistant map projection Distances starting one or two points, or along selected lines are correctly represented. This example is a cylindrical projection. Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

38. Compromise projection (Robinson) Distortions are optimized. This example is a pseudo- cylindrical projection. Source: http://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj_f.html

39. Projection systems used for topographic mapping in the World UTM: Universal Transverse Mercator TM: Transverse Mercator

40. 3.3 Principle of changing from one projection into another Transformation from one Cartesian coordinate system (with a known Projection A) to another is done by: –1.calculating the geographic coordinates for each point (inverse mapping equation) and then –2.calculating the Cartesian coordinates using the forward mapping equation of the target Projection B.

41. Changing from one projection into another

42. Comparison of projections (an example) Here, two maps of Northern and Central America are overlaid with a practical match of the borders of the USA. The differences between the two geometries are increasing with an increasing distance from the matching central part.

43. 3.4 Classification of map projections There are several ways to classify map projections. Here, you find a set of criteria for classifications, which were discussed before. Note that the last criterium (Inventor) refers to map geometry which are not really geometric projections, but sets of mathematical/logical rules for converting φ and λ into x and y coordinates.  Class Azimuthal Cylindrical Conical  Aspect Normal Oblique Transverse  Property Equivalent (or equal-area) Equidistant Conformal Compromise  Secant or Tangent projection plane  ( Inventor )

44. 3.5 Example of geometric information on a map On a map, the geometric information is presented in the colophon. This example is taken from a Spanish map. Source: Mapa topografico nacional de Espana; IGN; Sheet 1046-III

45. 3.6 A frequently used mapping system: Universal Transverse Mercator (UTM) Transverse secant cylinder (6 o zones)

46. A UTM zone Transverse cylindrical projection: the cylinder is tangent along meridians 60 zones of 6 degrees Zone 1 starts at longitude 180°(in the Pacific Ocean) Polar zones are separately mapped X coordinates – six digits (usually) Y coordinates – seven digits (usually) Source http://www.maptools.com/UsingUTM/UTMdetails.html

47. UTM zones 0o0o 6o6o

48. UTM zone coordinates The origin of the Cartezian coordinate system is translated outside of the zone to ensure positive coordinate values: –Eastings are measured from the central meridian with a 500,000 m False Easting to ensure positive coordinates –Northings are measured from the equator with a 10,000,000 m False Northing for positions South of the equator

49. Two adjacent UTM zones A overlap between the zones facilitates continuous mapping

50. Some stories of normal Mercator projection Greenland (blue) on Africa (red) based on the standard Mercator projection map compared to the actual geographical size Image source: http://www.pratham.name/mercator-projection-africa-vs-greenland.html

51. The true size of Africa Source: http://flowingdata.com/2010/10/18/true-size-of-africa/

52. 4 Summary Spatial referencing basics –Basic coordinate systems –Shape of the Earth: the geoid –Datums: vertical datum, horizontal datum Map projections –Classes of projections –Properties of projections –Projection transformations

53. Reading for this week Map Projection Overview Mercator projection Transverse Mercator projection Universal Transverse Mercator coordinate system 53

54. Next classes Friday class: –MapInfo Professional: Buffering, projection and printing In preparation: –Next Tuesday: Geo-statistical Computing and R 54