Download presentation
Presentation is loading. Please wait.
Published byAutumn Pugh Modified over 11 years ago
1
SADC Course in Statistics Comparing several proportions (Session 15)
2
To put your footer here go to View > Header and Footer 2 Learning Objectives By the end of this session, you will be able to conduct and interpret results from a chi- square test for comparing several proportions explain how results above can be extended to the study of associations in general r x c tables state assumptions underlying the above test and actions to take if assumptions fail
3
To put your footer here go to View > Header and Footer 3 Example with several proportions Below is a 5x2 table of observed frequencies showing animals who did or did not get diseased after inoculation with one of five vaccines. Vaccinediseasedhealthy Total A43237280 B52198250 C25245270 D48212260 E57233290 Total22511251350 Question: Does the proportion of diseased animals vary according to type of vaccine?
4
To put your footer here go to View > Header and Footer 4 Null and alternative hypotheses Translate the above question into a null hypothesis and an alternative hypothesis, i.e. H 0 : proportions are the same for each vaccine H 1 : proportions vary over vaccines If H 0 is true, best estimate of proportion is diseased total divided by grand total = 225/1350 = 0.167 We use this to compute expected values in each row of the table.
5
To put your footer here go to View > Header and Footer 5 Chi-square test Thus the procedure is exactly similar to the case of comparing two proportions. Again we compute the chi-square test-statistic given by If H 0 is true, X 2 follows a 2 distribution with 4 d.f. (number of proportions being compared minus 1). Comparing 16.56 to we get a p-value of 0.0024, a highly significant result.
6
To put your footer here go to View > Header and Footer 6 Conclusions There is strong evidence that the proportions of diseased animals are not all the same for all vaccines. Note: The chi-square value above is nearly the same as that obtained in the previous session with data from a 2x2 table. This is a coincidence, but note the difference in d.f. Previously for 2x2 table, d.f.=1. In above example, d.f.=4. So although the test statistic is the same, p- values are different.
7
To put your footer here go to View > Header and Footer 7 Extensions to r x c tables Survey results are often expressed in terms of 2-way tables. In general, such tables may contain r rows and c columns. Questions of interest in such tables centre on whether these is an association between the two variables that have been tabulated. For example if the table tabulates education level of HH head (none, primary, secondary, tertiary) by poverty levels (not poor, poor, very poor), the question is poverty related to education may be asked.
8
To put your footer here go to View > Header and Footer 8 Chi-square test for an rxc table To answer the above question, the null hypothesis is that the two variables are NOT related, against the alternative that they are. Under the null hypothesis, comparison of expected values with observed values leads to a chi-square test. The d.f. associated with this test = (r-1)(c-1). In the above example, the d.f.=(4-1)(3-1)=6
9
To put your footer here go to View > Header and Footer 9 Assumption underlying the test The chi-square test is approximate –Validity relies on large samples –Small samples of unbalanced data (large and small counts together) may invalidate the approximation Rules of thumb for validity involve the expected values, E –Need large expected values under H 0 –Say, most E5 and none less than 1 –If rule of thumb is not satisfied, may have an unreliable p-value
10
To put your footer here go to View > Header and Footer 10 Actions when assumptions fail (a) Simple approaches: Collect more data if this is possible Collapse rows or columns if the table has more than two rows/columns. But need to recognise that –this leads to loss of information –with some types of variables, there may be no natural way of combining rows/columns
11
To put your footer here go to View > Header and Footer 11 Actions when assumptions fail (b) Use a continuity correction This method is often called Yates correction and is applicable just to 2x2 tables. First we show the standard chi-square value corresponding to a table with cell counts a, b, c, d as below. (Verify later that this is correct) col1col2 row1abr1r1 row2cdr2r2 n1n1 n2n2 N
12
To put your footer here go to View > Header and Footer 12 Actions when assumptions fail (b) Continuity correction (continued)… The approximation of X 2 to the chi-square is improved by reducing the absolute value of O-E by ½ before calculating X 2. This results in the X 2 taking the value below. Note: The equivalent when comparing two proportions using an z-test is to reduce by ½, the r value for the first p=r/n and increase by ½ the r value for the second proportion.
13
To put your footer here go to View > Header and Footer 13 Example of use of continuity corr n Whether smoker? Job Driver ConductorTotal No 40 67.8% 52 78.8% 92 73.6% Yes 19 32.2% 14 21.2% 33 26.4% Total59 100.0% 66 100.0% 125 (100%) Above is the example on Bus data used during the practical sessions. Question of interest is whether the proportion of smokers are different across job types.
14
To put your footer here go to View > Header and Footer 14 Example of use of continuity corr n The usual chi-square test leads to X 2 =1.937 Applying the continuity correction, we get X 2 = 1.412 Here, there is little difference because the sample sizes are reasonably large. More important to apply the continuity correction for small sample sizes.
15
To put your footer here go to View > Header and Footer 15 Actions when assumptions fail (ctd) (c) Using an Exact Test When actions suggested in (a) or (b) are not possible, consider using an Exact Test. Details of such tests are beyond the scope of this module. However, the basic approach is to compute all possible tables having the same marginal totals, and examine how extreme the observed table is, in comparison. Some software packages (e.g. Stata) have the facility to perform Fishers exact test. SPSS does this only for 2x2 tables. Special software also exist for such tests, e.g. StatXact.
16
To put your footer here go to View > Header and Footer 16 Limitations Chi-square tests are limited, in that only two factors are examined at a time. This may cause erroneous inferences to be made (see Practical 15 for an example). The inter-relations between more than two factors can be investigating using more sophisticated statistical techniques, e.g. log-linear modelling.
17
To put your footer here go to View > Header and Footer 17 References Altman, D.G., Machin, D., Bryant, T.N., and Gardner, M.J. (2000) Statistics with confidence. (2nd Edition). BMJ Books, Bristol, UK. pp 240. Armitage, P., Matthews J.N.S. and Berry G. (2002). Statistical Methods in Medical Research. 4th edn. Blackwell.
18
To put your footer here go to View > Header and Footer 18 Some practical work follows…
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.